Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to...Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site.The roof behavior in the headgate near the face was carefully observed during longwall retreat.Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.展开更多
Longwall mining has a significant influence on gas wells located within longwall chain pillars.Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in ga...Longwall mining has a significant influence on gas wells located within longwall chain pillars.Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings.If the gas well casings are compromised or ruptured,natural gas could migrate into the mine workings,potentially causing a fire or explosion.By the current safety regulations,the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars.The current regulations for gas well pillar design are based on the 1957 Pennsylvania gas well pillar study.The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars.As the guidelines were developed for room-andpillar mining under shallow cover,they are no longer applicable to modern longwall coal mining,particularly,under deep cover.Gas well casing of failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study,conducted by the National Institute for Occupational Safety and Health(NIOSH),presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh Coal Seam.The study results indicate that overburden depth and pillar size are not the only determining factors for gas well stability.The other important factors include subsurface ground movement,overburden geology,weak floor,as well as the type of the construction of gas wells.Numerical modeling was used to model abutment pressure,subsurface deformations,and the response of gas well casings.The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above,within,and below the chain pillars,and the potential location and modes of gas well failures,thereby providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.展开更多
Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground fall fatalities in underground coal mines in the United States.The risk of ground falls during pillar recov...Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground fall fatalities in underground coal mines in the United States.The risk of ground falls during pillar recovery increases in multiple-seam mining conditions.The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave.When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction.This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 21 m of interburden under about 305 m of depth of cover.The study finds that, for interburden thickness of 21 m, the multiple-seam mining influence zone in the lower seam is directly under the barrier pillar within about 30 m from the gob edge of the upper seam.The peak stress in the interburden transfers down at an angle of approximately 20°away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat.The study also suggests that, for full pillar recovery in close-distance multiple-seam scenarios,it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars.If the entries and/or crosscuts in the lower seam are developed outside the gob line of the upper seam,additional roof and rib support needs to be considered to account for the elevated stress in the multiple-seam influence zone.展开更多
文摘Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site.The roof behavior in the headgate near the face was carefully observed during longwall retreat.Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.
文摘Longwall mining has a significant influence on gas wells located within longwall chain pillars.Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings.If the gas well casings are compromised or ruptured,natural gas could migrate into the mine workings,potentially causing a fire or explosion.By the current safety regulations,the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars.The current regulations for gas well pillar design are based on the 1957 Pennsylvania gas well pillar study.The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars.As the guidelines were developed for room-andpillar mining under shallow cover,they are no longer applicable to modern longwall coal mining,particularly,under deep cover.Gas well casing of failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study,conducted by the National Institute for Occupational Safety and Health(NIOSH),presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh Coal Seam.The study results indicate that overburden depth and pillar size are not the only determining factors for gas well stability.The other important factors include subsurface ground movement,overburden geology,weak floor,as well as the type of the construction of gas wells.Numerical modeling was used to model abutment pressure,subsurface deformations,and the response of gas well casings.The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above,within,and below the chain pillars,and the potential location and modes of gas well failures,thereby providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.
文摘Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground fall fatalities in underground coal mines in the United States.The risk of ground falls during pillar recovery increases in multiple-seam mining conditions.The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave.When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction.This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 21 m of interburden under about 305 m of depth of cover.The study finds that, for interburden thickness of 21 m, the multiple-seam mining influence zone in the lower seam is directly under the barrier pillar within about 30 m from the gob edge of the upper seam.The peak stress in the interburden transfers down at an angle of approximately 20°away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat.The study also suggests that, for full pillar recovery in close-distance multiple-seam scenarios,it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars.If the entries and/or crosscuts in the lower seam are developed outside the gob line of the upper seam,additional roof and rib support needs to be considered to account for the elevated stress in the multiple-seam influence zone.
