Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent...Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.展开更多
Yielding support is often used in the squeezing tunnel to prevent damage to the lining induced by large deformation of the surrounding rock.Highly Deformable Elements(HDE)which is often installed along the circumferen...Yielding support is often used in the squeezing tunnel to prevent damage to the lining induced by large deformation of the surrounding rock.Highly Deformable Elements(HDE)which is often installed along the circumferential direction of the shotcrete lining is a common type of yielding support.To determine the yield parameters of HDE,the support characteristic of the lining using HDE and the ground pressure considering strain-softening of soft rock were analyzed by an analytical method.The analytical solution showed that when considering the strain-softening of squeezing ground,the ground pressure has a non-zero minimum value.The minimum value of ground stress can be used to determine the constant yield stress of the HDE,and the corresponding deformation of the minimum ground pressure can be used to determine the deformation capacity of the HDE.Based on the variation in the design constant yield stress and yield displacement of HDE with the in-situ stress and the mechanical parameters of the soft rock,equations were proposed for determining of the yield parameters of the HDE.展开更多
基金the support of the National Natural Science Foundation of China(Grant Nos.42207199,52179113,42272333)Zhejiang Postdoctoral Scientific Research Project(Grant Nos.ZJ2022155,ZJ2022156)。
文摘Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.
基金the support of the National Natural Science Foundation of China(Grant Nos.52179113,51991392 and 52279119)the Second Comprehensive Scientific Expedition on the Tibetan Plateau(No.2019QZKK0904)。
文摘Yielding support is often used in the squeezing tunnel to prevent damage to the lining induced by large deformation of the surrounding rock.Highly Deformable Elements(HDE)which is often installed along the circumferential direction of the shotcrete lining is a common type of yielding support.To determine the yield parameters of HDE,the support characteristic of the lining using HDE and the ground pressure considering strain-softening of soft rock were analyzed by an analytical method.The analytical solution showed that when considering the strain-softening of squeezing ground,the ground pressure has a non-zero minimum value.The minimum value of ground stress can be used to determine the constant yield stress of the HDE,and the corresponding deformation of the minimum ground pressure can be used to determine the deformation capacity of the HDE.Based on the variation in the design constant yield stress and yield displacement of HDE with the in-situ stress and the mechanical parameters of the soft rock,equations were proposed for determining of the yield parameters of the HDE.
