Design and preparation of Al-Fe-Ce ternary aluminum alloys with high thermal conductivity

Ce element was introduced to modify Al−2%Fe(mass fraction)binary alloy.The microstructures,crystallization behavior,electrical/thermal conductivities and mechanical properties of these alloys were systematically investigated.The results indicated that the appropriate Ce addition decreased the recalescence temperature and growth temperature of Al−Fe eutectic structure,improved the morphology and distribution of Fe-containing phase,and simultaneously increased the conductivity and mechanical properties.The annealed treatment improved the thermal conductivity of these alloys due to the decreasing concentration of point defects.Rolling process further broke up the coarser Fe-containing phases into finer particles and made the secondary phases uniformly distributed in theα(Al)matrix.After subsequent annealing treatment and rolling deformation,the thermal conductivity,ultimate tensile strength and hardness of the Al−2%Fe−0.3%Ce(mass fraction)alloy reached 226 W/(m·K),(182±1.4)MPa and HBW(49.5±1.7),respectively.

Chemical components of Dendrobium crepidatum and their neurite outgrowth enhancing activities

15 compounds,including two new ones crepidatuols A(1)and B(2)were isolated from the stems of Dendrobium crepidatum.The planar structures of these compounds were elucidated by spectroscopic methods(NMR,MS,UV,and IR)and comparison with those from literatures.10 compounds were send for enhancing activities on nerve growth factor(NGF)medicated neurite outgrowth in PC12 cells and the results indicated that crepidatuol A(1),confusarin and 3-(2-acetoxy-5-methoxy)-phenylpropanol showed enhancing activities at the concentration of 10.0μM.

Grain refinement of Mg−Al binary alloys inoculated by in-situ oxidation

Utilizing oxide inclusion to induce heterogeneous nucleation event is an available method to achieve grain refinement.In this study,Mg−Al binary alloys were refined by inoculation of in-situ oxidation process.Results show that MgO and MgAl_(2)O_(4) phases are primary oxide products for Mg−xAl alloys inoculated by in-situ oxidation.For pure Mg and Mg−1Al alloy,MgO is the only oxide product.MgAl_(2)O_(4) is another oxide product for Mg−xAl alloy as Al content increases to 3 wt.%.For Mg−3Al alloy,average grain size significantly decreases from 1135 to 237μm,with a high grain refining ratio of 79.1%.Both MgO and MgAl_(2)O_(4) possess nucleating potency forα-Mg grain.MgAl_(2)O_(4) exhibits a higher nucleating potency due to the lower misfit withα-Mg.The grain refinement of Mg−xAl alloys inoculated by in-situ oxidation process is attributed to heterogeneous nucleation events ofα-Mg grains on MgO or MgAl_(2)O_(4) particles.

Influence of particle packing structure on sound velocity

The anisotropy in the particle systems of different packing structures affects the sound velocity. The acoustic propagation process in four kinds of packing structures（denoted as S45, H60, S90, and D） of two-dimensional granular system is simulated by the discrete element method. The velocity vtof obtained by the time of flight method and the velocity vc obtained from the stiffness tensor of the system are compared. Different sound velocities reflect various packing structures and force distributions within the system. The compression wave velocities of H60 and S90 are nearly the same, and transmit faster than that of D packing structure, while the sound velocity of S45 is the smallest. The shear wave velocities of S45 and H60 are nearly the same, and transmit faster than that of D packing structure. The compression wave velocity is sensitive to the volume fraction of the structure, however, the shear wave velocity is more sensitive to the geometrical structure itself. As the normal stress p is larger than 1 MPa, vtof and vc are almost equal, and the stiffness tensors of various structures explain the difference of sound velocities. When the normal stress is less than 1 MPa, with the coordination number unchanged, the law vtof ∝ p^1/4 still exists. This demonstrates that apart from different power laws between force and deformation as well as the change of the coordination number under different stresses, there are other complicated causes of vtof∝ p^1/4, and an explanation of the deviation from vtof ∝ p^1/6 is given from the perspective of dissipation.