期刊文献+
共找到2篇文章
< 1 >
每页显示 20 50 100
Electrochemical hydriding performance of Mg-TM-Mm (TM=transition metals,Mm=mischmetal) alloys for hydrogen storage 被引量:5
1
作者 V.KNOTEK d.vojtech 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2013年第7期2047-2059,共13页
Eighteen as-cast binary Mg-Ni, Mg-Mm and ternary Mg-Ni-Mm and Mg-Ni-TM (TM=transition metals (Cu, Zn, Mn and Co); Mm = mischmetal containing Ce, La, Nd and Pr) alloys were hydrided by an electrochemical process to... Eighteen as-cast binary Mg-Ni, Mg-Mm and ternary Mg-Ni-Mm and Mg-Ni-TM (TM=transition metals (Cu, Zn, Mn and Co); Mm = mischmetal containing Ce, La, Nd and Pr) alloys were hydrided by an electrochemical process to determine the alloys with the most potential for electrochemical hydrogen storage. The alloys were hydrided in a 6 mol/L KOH solution at 80 °C for 480 min and at 100 A/m2. To assess the electrochemical hydriding performance of alloys, maximum hydrogen concentrations, hydrogen penetration depths and total mass of absorbed hydrogen in the alloys were measured by glow discharge spectrometry. In addition, the structures and phase compositions of the alloys both before and after hydriding were studied by optical and scanning electron microscopy, energy dispersive spectrometry and X-ray diffraction. It was determined that the highest total amount of hydrogen was absorbed by the Mg-25Ni-12Mm and Mg-26Ni (mass fraction, %) alloys. The maximum hydrogen concentrations in the Mg-25Ni-12Mm and Mg-26Ni alloys were 1.0% and 1.6%, respectively. The main hydriding product was the binary MgH2 hydride, and the ternary Mg2NiH4 hydride was also detected in the Mg-25Ni-12Mm alloy. The electrochemical hydriding parameters achieved are discussed in relation to the structures of alloys, alloying elements and hydriding mechanisms. 展开更多
关键词 hydrogen storage MAGNESIUM nickel rare earths electrochemical hydriding
下载PDF
Microstructure and mechanical properties of the micrograined hypoeutectic Zn–Mg alloy 被引量:3
2
作者 J. Kubasek d.vojtech +2 位作者 I.Pospisilova A.Michalcova J.Maixner 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2016年第10期1167-1176,共10页
A biodegradable Zn alloy, Zn-1.6Mg, with the potential medical applications as a promising coating material for steel components was studied in this work. The alloy was prepared by three different procedures: gravity... A biodegradable Zn alloy, Zn-1.6Mg, with the potential medical applications as a promising coating material for steel components was studied in this work. The alloy was prepared by three different procedures: gravity casting, hot extrusion, and a combination of rapid solidification and hot extrusion. The samples prepared were characterized by light microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction analysis. Vickers hardness, tensile, and compressive tests were performed to determine the samples' mechanical properties. Structural examination reveals that the average grain sizes of samples prepared by gravity casting, hot extrusion, and rapid solidification followed by hot extrusion are 35.0, 9.7, and 2.1 μm, respectively. The micrograined sample with the finest grain size exhibits the highest hardness(Hv = 122 MPa), compressive yield strength(382 MPa), tensile yield strength(332 MPa), ultimate tensile strength(370 MPa), and elongation(9%). This sample also demonstrates the lowest work hardening in tension and temporary softening in compression among the prepared samples. The mechanical behavior of the samples is discussed in relation to the structural characteristics, Hall-Petch relationship, and deformation mechanisms in fine-grained hexagonal-close-packed metals. 展开更多
关键词 zinc magnesium alloys extrusion rapid solidification microstructure mechanical properties
下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部