A magnesium alloy containing essential,non-toxic,biodegradable elements such as Ca and Zn has been fabricated using a novel twin-roll casting process(TRC).Microstructure,mechanical properties,in vivo corrosion and bio...A magnesium alloy containing essential,non-toxic,biodegradable elements such as Ca and Zn has been fabricated using a novel twin-roll casting process(TRC).Microstructure,mechanical properties,in vivo corrosion and biocompatibility have been assessed and compared to the properties of the rare earth(RE)element containing WE43 alloy.TRC Mg-0.5 wt% Zn-0.5 wt% Ca exhibited fine grains with an average grain size ranging from 70 to 150μm.Mechanical properties of a TRC Mg-0.5Zn-0.5Ca alloy showed an ultimate tensile strength of 220 MPa and ductility of 9.3%.The TRC Mg-0.5Zn-0.5Ca alloy showed a degradation rate of 0.51±0.07 mm/y similar to that of the WE43 alloy(0.47±0.09 mm/y)in the rat model after 1 week of implantation.By week 4 the biodegradation rates of both alloys studied were lowered and stabilized with fewer gas pockets around the implant.The histological analysis shows that both WE43 and TRC Mg-0.5Zn-0.5Ca alloy triggered comparable tissue healing responses at respective times of implantation.The presence of more organized scarring tissue around the TRC Mg-0.5Zn-0.5Ca alloys suggests that the biodegradation of the RE-free alloy may be more conducive to the tissue proliferation and remodelling process.展开更多
The microstructure, hardness, and precipitate free zones(PFZ) of V55Ti30Ni15 alloys during heat treatment have been investigated in this study. The microstructure resulting from different heat treatment conditions h...The microstructure, hardness, and precipitate free zones(PFZ) of V55Ti30Ni15 alloys during heat treatment have been investigated in this study. The microstructure resulting from different heat treatment conditions has a great influence on hardness. The microstructure resulting from different heat treatment conditions has a great influence on hardness. Fine Ni Ti particles precipitate from the supersaturated V-matrix solid solution at 750 °C, increase in quantity until 800 °C, and then dissolve back into the V-matrix at 850 °C. The resultant hardness decreases with temperature until 800 °C, and then increases from 800 to 850 °C. The microstructure containing small Ni Ti precipitates resulting from the treatment of 18 h at800 °C has a good soft condition for workability. PFZ formed at the grain boundary of V-matrix during heat treatment was observed. Vacancies depletion in V-matrix maybe led to the formation of PFZ.展开更多
基金the support of the Australian Research Council through the ARC Research Hub for Advanced Manufacturing of Medical Devices(IH150100024).
文摘A magnesium alloy containing essential,non-toxic,biodegradable elements such as Ca and Zn has been fabricated using a novel twin-roll casting process(TRC).Microstructure,mechanical properties,in vivo corrosion and biocompatibility have been assessed and compared to the properties of the rare earth(RE)element containing WE43 alloy.TRC Mg-0.5 wt% Zn-0.5 wt% Ca exhibited fine grains with an average grain size ranging from 70 to 150μm.Mechanical properties of a TRC Mg-0.5Zn-0.5Ca alloy showed an ultimate tensile strength of 220 MPa and ductility of 9.3%.The TRC Mg-0.5Zn-0.5Ca alloy showed a degradation rate of 0.51±0.07 mm/y similar to that of the WE43 alloy(0.47±0.09 mm/y)in the rat model after 1 week of implantation.By week 4 the biodegradation rates of both alloys studied were lowered and stabilized with fewer gas pockets around the implant.The histological analysis shows that both WE43 and TRC Mg-0.5Zn-0.5Ca alloy triggered comparable tissue healing responses at respective times of implantation.The presence of more organized scarring tissue around the TRC Mg-0.5Zn-0.5Ca alloys suggests that the biodegradation of the RE-free alloy may be more conducive to the tissue proliferation and remodelling process.
基金China Scholarship Council for the financial support for Peng Jiang’s study at CSIRO
文摘The microstructure, hardness, and precipitate free zones(PFZ) of V55Ti30Ni15 alloys during heat treatment have been investigated in this study. The microstructure resulting from different heat treatment conditions has a great influence on hardness. The microstructure resulting from different heat treatment conditions has a great influence on hardness. Fine Ni Ti particles precipitate from the supersaturated V-matrix solid solution at 750 °C, increase in quantity until 800 °C, and then dissolve back into the V-matrix at 850 °C. The resultant hardness decreases with temperature until 800 °C, and then increases from 800 to 850 °C. The microstructure containing small Ni Ti precipitates resulting from the treatment of 18 h at800 °C has a good soft condition for workability. PFZ formed at the grain boundary of V-matrix during heat treatment was observed. Vacancies depletion in V-matrix maybe led to the formation of PFZ.