Effect of Defects at the Buffer Layer CdS/Absorber CIGS Interface on CIGS Solar Cell Performance

This scientific paper presents a study investigating the effects of defects at the CdS/CIGS and CdS/SDL interfaces on the performance of CIGS solar cells. The objective of this study is to analyze the influence of defects at the interface between the CdS buffer layer and the CIGS absorber, as well as the surface defect layer (SDL), on CIGS solar cell performance. The study explores three key aspects: the impact of the conduction band offset (CBO) at the CdS/CIGS interface, the effects of interface defects and defect density on performance, and the combined influence of CBO and defect density at the CdS/ SDL and SDL/CIGS interfaces. For interface defects not exceeding 1013 cm-2, we obtained a good efficiency of 22.9% when -0.1 eV analyzing the quality of CdS/SDL and SDL/CIGS junctions, it appears that defects at the SDL/CIGS interface have very little impact on the performances of the CIGS solar cell. By optimizing the electrical parameters of the CdS/SDL interface defects, we achieved a conversion efficiency of 23.1% when -0.05 eV < CBO < 0.05 eV.

Influence of Defect Density, Band Gap Discontinuity and Electron Mobility on the Performance of Perovskite Solar Cells

In this manuscript, we used the SCAPS-1D software to perform numerical simulations on a perovskite solar cell. These simulations were used to study the influence of certain parameters on the electrical behavior of the cell. We have shown in this study that electron mobility is strongly influenced by the thickness of the absorber, since electron velocity is reduced by thickness. The influence of the defect density shows that above 1016 cm-3 all the electrical parameters are affected by the defects. The band discontinuity at the interface generally plays a crucial role in the charge transport phenomenon. The importance of this study is to enable the development of good quality perovskite solar cells, while taking into account the parameters that limit solar cell performance.

High Performance for Cu(In,Ga)Se2 Quaternary System-Based Solar Cells with Alternative Buffer Layers

In this study, the authors investigated the performance of different buffer layers through the electrical parameters such as Jsc, Voc, QE and η of the quaternary system Cu(In,Ga)Se2 solar cells. The performance of Cu(In,Ga)Se2solar cells has been modeled and numerically simulated by using the SCAPS- 1D device simulation tool. The cells with a ZnSe, Zn(O,S) and (Zn,Mg)O buffer layers were compared with the reference CdS buffer layer. The investigation of ZnSe, Zn(O, S) and (Zn,Mg)O-based cells to substitute the traditional CdS in the future shows that the ZnSe-buffer layer is a potential material to replace CdS, which revealed the best efficiency of 20.76%, the other electrical parameters are: JSC = 34.6 mA/cm2, VOC = 0.76 V and FF = 79.6%. The losses as a function of the temperature are estimated at 0.1%/K, among all kinds of buffer layers studied. We have also shown that the use of a high band-gap buffer layer is necessary to obtain a better short-circuit current density JSC. From our results, we note that the chalcogenide solar cells with Zn-based alternative buffer layer have almost the same stability thatthe traditional CdS buffer layer solar cells have.

Renewable Energies in Africa, Context and Socio-Economic Challenge

In this paper, we have shown that Africa has an enormous wealth of renewable energy resources among the most important in the world such as the strong sunshine, Congo and Nile Rivers respectively among the most powerful and the longest in the world. We have underlined the presence of important forests, rich subsoil in mineral elements, and strong winds. In addition to a rapidly growing human capital, Africa, therefore, has at its disposal all the factors enabling it to initiate sustainable and inclusive socio-economic development. We have shown that the transformation of these renewable energies is an opportunity for Africa to reach its socio-economic challenges. The development of renewable energies in Africa will be a source of many financial benefits and advantages both in terms of improving living conditions and carrying out activities. The electrical supply of rural areas of Africa represents a considerable issue, which can be a propellant factor in long-term socio-economic development if the conditions of use of clean fuel and cooking technologies, especially sanitary are taken into account. The provision of modern energy services can contribute to the creation of jobs for young people upstream. Among other things, we can note the development of local skills, the creation of income-generating activities, and the improvement of hygiene and health measures which are necessary conditions for family and social well-being. This requires a policy focused, on research in general and in particular on semiconductors that participate in the transformation of photovoltaic solar energy. We have stressed that Africa which is currently experiencing a period of economic growth and sustained transformation must be very looking at in its energy policy and give pride of place to renewable energies to initiate sustainable socio-economic development, equitable and inclusive different social strata both in rural areas and urban areas.

Comprehensive Analysis of CuIn_1-xGa_xSe₂Based Solar Cells with Zn_1-yMg_yO Buffer Layer

The development of cadmium-free CIGS solar cells with high conversion efficiency is crucial due to the toxicity of cadmium. Zinc-based buffer layers seem to be the most promising. In this paper, a numerical analysis using SCAPS-1D software was used to explore the Zn(Mg,O) layer as an alternative to the toxic CdS layer. The effect of several properties such as thickness, doping, Mg concentration of the Zn(Mg,O) layer on the current-voltage parameters was explored and their optimal values were proposed. The simulation results reveal that the optimal value of the ZMO layer thickness is approximately 40 nm, the doping at 1017 cm-3 and an Mg composition between 0.15 and 0.2. In addition, the effect of Gallium (Ga) content in the absorber as well as the Zn(Mg,O)/CIGS interface properties on the solar cell’s performance was examined. The results show that contrary to the CdS buffer layer, the best electrical characteristics of the ZMO/CIGS heterojunction are obtained using a Ga-content equal to 0.4 and high interface defect density or unfavorable band alignment may be the causes of poor performances of Zn(Mg,O)/CIGS solar cells in the case of low and high Mg-contents.

Required CIGS and CIGS/Mo Interface Properties for High-Efficiency Cu(In, Ga)Se<SUB>2</SUB>Based Solar Cells

In this work, we have modeled and simulated the electrical performance of CIGS thin-film solar cell using one-dimensional simulation software (SCAPS-1D). Starting from a baseline model that reproduced the experimental results, the properties of the absorber layer and the CIGS/Mo interface have been explored, and the requirements for high-efficiency CIGS solar cell were proposed. Simulation results show that the band-gap, acceptor density, defect density are crucial parameters that affect the performance of the solar cell. The best conversion efficiency is obtained when the absorber band-gap is around 1.2 eV, the acceptor density at 1016 cm−3 and the defect density less than 1014 cm−3. In addition, CIGS/Mo interface has been investigated. It appears that a thin MoSe2 layer reduces recombination at this interface. An improvement of 1.5 to 2.5 mA/cm2 in the current density (Jsc) depending on the absorber thickness is obtained.

Optimization of Mo/Cu(In,Ga)Se2/CdS/ZnO Hetero-Junction Solar Cell Performance by Numerical Simulation with SCAPS-1D

The paper presents a one-dimensional simulation study of chalcopyrite Cu(In,Ga)Se2(CIGS)solar cells,where the effects of the variation of CIGS,CdS,and ZnO layers are presented.Additionlly the influence of the variation of doping and the defects density of shallow uniform donors and acceptors types are also presented.The analyse of the simulation results shows that recombination inside the space charge region(SCR)decrease more our CIGS solar cell model performance.We also found that the electrical parameters increase with increasing CIGS absorber doping density exception of JSC values that reach their maximum at 1016cm-3 and decrease due to recombination of charge carriers in the p-n junction particularly the recombination inside the SCR.We also stressed the fact that the effects of shallow uniforme donor density is very low on the performance of our CIGS solar cell model is important because it will allow to control the width of space charge region from shallow uniform acceptors defect density that has a strong influence on the different electrical parameters.Yet,good optimization of performance of the CIGS-based solar cell necessarily passes though a good control of the space charge region width and will constitute a boosting perspective for the preparation of our next paper.We contact that the results obtained of the numerical simulation with SCAPS-1D show a good agreement comparatively of the literature results.The simulation of our CIGS solar cell presents best performances if the values of the absorber layer thickness is in the range of 0.02 to 0.03μm,the buffer layer thickness is in the range of 0.02 to 0.06μm and the defects density of shallow uniform acceptors types is in the range of 1015 to 1017cm-3.