The design of remediation works for the mitigation and prevention of the associated risk is needed where these geological hazards affect anthropized areas. Remedial measures for landslides commonly include slope resha...The design of remediation works for the mitigation and prevention of the associated risk is needed where these geological hazards affect anthropized areas. Remedial measures for landslides commonly include slope reshaping, plumbing, drainage, retaining structures and internal slope reinforcement, while debris flow control works consist in open or closed control structures. The effectiveness of the remedial works implemented must be assessed by evaluating the reduction of the risk over time. The choice of the most appropriate and cost-effective intervention must consider the type of hazard and environmental issues, and selects, wherever possible, naturalistic engineering operations that are consequently implemented according to the environmental regulations or the design and specification standards imposed by the competent public administrations. The mitigation procedures consist of five basic steps:(a) acquisition of the knowledge of the hazard process;(b) risk assessment with identification of possible disaster scenarios;(c) planning and designing of specific remedial measures to reduce and/or eliminate the potential risk;(d) slope monitoring after application of remedial measures,(e) transfer of knowledge to the stakeholders. This paper presents two case studies describing the practice for the design of the mitigation measures adopted for debris flow and active landslide sites in North-Eastern Italy. The first case study is a debris flow site, for which, based on observation of past events and numerical simulations using the software FLOW-2D, the most suitable mitigation measures were found to be the construction of a debris basin, barriers and breakers. The second case study deals with an active landslide threatening a village. Based on the landslide kinematics and the results of numerical simulations performed with the code FLAC, hard engineering remedial works were planned to reduce the driving forces with benching and by increasing the available resisting forces using jet grout piles and deep drainage.展开更多
The aim of this research is to deepen the knowledge of the role of friction on the dynamics of granular media; in particular the friction angle is taken into consideration as the physical parameter that drives stabili...The aim of this research is to deepen the knowledge of the role of friction on the dynamics of granular media; in particular the friction angle is taken into consideration as the physical parameter that drives stability, motion and deposition of a set of grains of any nature and size. The idea behind this work is a question: is the friction angle really that fundamental and obvious physical parameter which rules stability and motion of granular media as it seems from most works which deal with particle dynamics? The experimental study tries to answer this question with a series of laboratory tests, in which different natural and artificial granular materials have been investigated in dry condition by means of a tilting flume. The characteristic friction angles, both in deposition(repose) and stability limit(critical) conditions, were measured and checked against size, shape, density and roughness of the considered granular material. The flume tests have been preferred to "classical" geotechnical apparatuses(e.g. shear box) since the flume experimental conditions appear closer to the natural ones of many situations of slope stability interest(e.g. a scree slope). The results reveal that characteristic friction angles depend on size and shape of grains while mixtures of granules of different size show some sorting mechanism with less clear behaviour.展开更多
文摘The design of remediation works for the mitigation and prevention of the associated risk is needed where these geological hazards affect anthropized areas. Remedial measures for landslides commonly include slope reshaping, plumbing, drainage, retaining structures and internal slope reinforcement, while debris flow control works consist in open or closed control structures. The effectiveness of the remedial works implemented must be assessed by evaluating the reduction of the risk over time. The choice of the most appropriate and cost-effective intervention must consider the type of hazard and environmental issues, and selects, wherever possible, naturalistic engineering operations that are consequently implemented according to the environmental regulations or the design and specification standards imposed by the competent public administrations. The mitigation procedures consist of five basic steps:(a) acquisition of the knowledge of the hazard process;(b) risk assessment with identification of possible disaster scenarios;(c) planning and designing of specific remedial measures to reduce and/or eliminate the potential risk;(d) slope monitoring after application of remedial measures,(e) transfer of knowledge to the stakeholders. This paper presents two case studies describing the practice for the design of the mitigation measures adopted for debris flow and active landslide sites in North-Eastern Italy. The first case study is a debris flow site, for which, based on observation of past events and numerical simulations using the software FLOW-2D, the most suitable mitigation measures were found to be the construction of a debris basin, barriers and breakers. The second case study deals with an active landslide threatening a village. Based on the landslide kinematics and the results of numerical simulations performed with the code FLAC, hard engineering remedial works were planned to reduce the driving forces with benching and by increasing the available resisting forces using jet grout piles and deep drainage.
文摘The aim of this research is to deepen the knowledge of the role of friction on the dynamics of granular media; in particular the friction angle is taken into consideration as the physical parameter that drives stability, motion and deposition of a set of grains of any nature and size. The idea behind this work is a question: is the friction angle really that fundamental and obvious physical parameter which rules stability and motion of granular media as it seems from most works which deal with particle dynamics? The experimental study tries to answer this question with a series of laboratory tests, in which different natural and artificial granular materials have been investigated in dry condition by means of a tilting flume. The characteristic friction angles, both in deposition(repose) and stability limit(critical) conditions, were measured and checked against size, shape, density and roughness of the considered granular material. The flume tests have been preferred to "classical" geotechnical apparatuses(e.g. shear box) since the flume experimental conditions appear closer to the natural ones of many situations of slope stability interest(e.g. a scree slope). The results reveal that characteristic friction angles depend on size and shape of grains while mixtures of granules of different size show some sorting mechanism with less clear behaviour.