The unsupported sleeper can change the load characteristics of ballast particles and thus affect the dynamic stability of a ballasted bed.In this work,a laboratory test was constructed on a ballasted track containing ...The unsupported sleeper can change the load characteristics of ballast particles and thus affect the dynamic stability of a ballasted bed.In this work,a laboratory test was constructed on a ballasted track containing unsupported sleepers.The ballasted track was excited by a wheelset,and the influence of unsupported sleepers on the dynamic stability of a ballasted bed was studied.The results show that the main frequency of the sleeper vibration appeared at 670 Hz,and the first-order rigid vibration mode at the frequency of 101 Hz had a significant effect on the condition without the unsupported sleeper.When the sleepers were continuously unsupported,the vibration damping effect of ballasted bed within the frequency range of 0–450 Hz was better than that at higher frequencies.Within the frequency range of 70–250 Hz,the vibration damping effect of the ballasted bed with unsupported sleepers was better than that without the unsupported sleeper.Owing to the excitation from the wheelset impact,the lateral resistance of the ballasted bed with unsupported sleepers whose hanging heights were 30,60,and 90 mm increased by 37.43%,12.25%,and 18.23%,respectively,while the lateral resistance of the ballasted bed without the unsupported sleeper remained basically unchanged.The unsupported sleeper could increase the difference in the quality of the ballasted bed between two adjacent sleepers.In addition,test results show that the hanging height of the unsupported sleeper had little effect on the lateral resistance of a ballasted bed without external excitation,but had an obvious effect on the rate of change of the lateral resistance of a ballasted bed and the acceleration amplitude of the sleeper vibration under the wheelset impact.展开更多
The technology of continuously welded rails (CWRs) is important in modern railway track structures. To measure rail stress, resistance strain gauges are preferred due to their good stability, sensitivity, and esist...The technology of continuously welded rails (CWRs) is important in modern railway track structures. To measure rail stress, resistance strain gauges are preferred due to their good stability, sensitivity, and esistance to external interference. Based on the bi-directional strain method, we present a new method for measuring longitudinal rail stress using resistance strain gauges and develop a monitoring device for rail stress to realize long-term and multi-point measurement. Also relevant experimental verification and analysis are conducted. Results indicate that under various constraints the rail stress–strain values can be calculated just with the measured total longitudinal strain and total vertical strain. Considering the measurement error caused by sectional feature of sensors, we put forward a correction equation applicable to different stress conditions. Although the temperature values of the four full-bridge stress gauges can offset each other, the measurement error caused by rail flexural strain can also be eliminated to a certain extent at the same time, the nonuniform distribution of rail cross section temperature and unbalanced flexural strain still affect the measurement error. The experimental results also show that the developed rail-stress-monitoring sensor is suitable for measuring rail stress with reliable working performance.展开更多
基金The present work was supported by the National Natural Science Foundation of China(No.52008395).
文摘The unsupported sleeper can change the load characteristics of ballast particles and thus affect the dynamic stability of a ballasted bed.In this work,a laboratory test was constructed on a ballasted track containing unsupported sleepers.The ballasted track was excited by a wheelset,and the influence of unsupported sleepers on the dynamic stability of a ballasted bed was studied.The results show that the main frequency of the sleeper vibration appeared at 670 Hz,and the first-order rigid vibration mode at the frequency of 101 Hz had a significant effect on the condition without the unsupported sleeper.When the sleepers were continuously unsupported,the vibration damping effect of ballasted bed within the frequency range of 0–450 Hz was better than that at higher frequencies.Within the frequency range of 70–250 Hz,the vibration damping effect of the ballasted bed with unsupported sleepers was better than that without the unsupported sleeper.Owing to the excitation from the wheelset impact,the lateral resistance of the ballasted bed with unsupported sleepers whose hanging heights were 30,60,and 90 mm increased by 37.43%,12.25%,and 18.23%,respectively,while the lateral resistance of the ballasted bed without the unsupported sleeper remained basically unchanged.The unsupported sleeper could increase the difference in the quality of the ballasted bed between two adjacent sleepers.In addition,test results show that the hanging height of the unsupported sleeper had little effect on the lateral resistance of a ballasted bed without external excitation,but had an obvious effect on the rate of change of the lateral resistance of a ballasted bed and the acceleration amplitude of the sleeper vibration under the wheelset impact.
基金the fund support by the National Natural Science Foundation of China (No. 51425804, No. U1234201 and No. U1334203)
文摘The technology of continuously welded rails (CWRs) is important in modern railway track structures. To measure rail stress, resistance strain gauges are preferred due to their good stability, sensitivity, and esistance to external interference. Based on the bi-directional strain method, we present a new method for measuring longitudinal rail stress using resistance strain gauges and develop a monitoring device for rail stress to realize long-term and multi-point measurement. Also relevant experimental verification and analysis are conducted. Results indicate that under various constraints the rail stress–strain values can be calculated just with the measured total longitudinal strain and total vertical strain. Considering the measurement error caused by sectional feature of sensors, we put forward a correction equation applicable to different stress conditions. Although the temperature values of the four full-bridge stress gauges can offset each other, the measurement error caused by rail flexural strain can also be eliminated to a certain extent at the same time, the nonuniform distribution of rail cross section temperature and unbalanced flexural strain still affect the measurement error. The experimental results also show that the developed rail-stress-monitoring sensor is suitable for measuring rail stress with reliable working performance.