The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The beh...The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The behavior of the seal’s rubber material was taken into account by a large-strain viscoelastic, so called generalized Maxwell model, based on Dynamic Mechanical Thermal Analyses (DMTA) and tensile measurements. The pre-loaded garter spring was modelled with a bilinear material model and the shaft was assumed to be linear elastic. The density, coefficient of thermal expansion and the thermal conductance of the materials were taken into consideration during simulation. The friction between the rotary shaft seal and the shaft was simplified and modelled as a constant parameter. The iterative algorithm was evaluated at two different times, right after assembly and 1 h after assembly, so that rubber material’s stress relaxation effects are also incorporated. The results show good correlation with the literature data, which state that the permissible temperature for NBR70 (nitrile butadiene rubber) material contacting with ~80 mm shaft diameter, rotating at 2600/min is 100°C. The results show 107°C and 104°C for the two iterations. The effect of friction induced temperature, changes the width of the contact area between the seal and the shaft, and significantly reduces the contact pressure.展开更多
In this paper the behavior of an O-ring made of NBR rubber was investigated under extreme conditions. The effect of the extreme initial compression, operating pressure and extreme temperature conditions were examined....In this paper the behavior of an O-ring made of NBR rubber was investigated under extreme conditions. The effect of the extreme initial compression, operating pressure and extreme temperature conditions were examined. The rubber material was tested in simple tension, pure shear and equibiaxial tension modes complemented with a Dynamic Mechanical Thermal Analysis (DMTA) to capture the viscoelastic behavior of the material. For the investigation, a large-strain viscoelastic material model was developed by the authors, to take into account the large deformations caused by extreme conditions. Insufficient space during installation causes extreme initial compression consequently leading the material to crack on the contacting outer surfaces. It was found that the excessive strain and friction induced shear stress contributes primarily to this phenomenon. Extreme operating pressure causes the seal to penetrate into the gap between the shaft and the housing. This behavior damages the material and cracks appear on the seal. High strain areas were found in the proximity of the gap in the material. The analysis of the extreme operating temperature showed that during cooling the O-ring can completely loose its ability to seal at -70°C. There are three contributing factors: the speed of cooling, the temperature and the coefficient of thermal expansion.展开更多
文摘The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The behavior of the seal’s rubber material was taken into account by a large-strain viscoelastic, so called generalized Maxwell model, based on Dynamic Mechanical Thermal Analyses (DMTA) and tensile measurements. The pre-loaded garter spring was modelled with a bilinear material model and the shaft was assumed to be linear elastic. The density, coefficient of thermal expansion and the thermal conductance of the materials were taken into consideration during simulation. The friction between the rotary shaft seal and the shaft was simplified and modelled as a constant parameter. The iterative algorithm was evaluated at two different times, right after assembly and 1 h after assembly, so that rubber material’s stress relaxation effects are also incorporated. The results show good correlation with the literature data, which state that the permissible temperature for NBR70 (nitrile butadiene rubber) material contacting with ~80 mm shaft diameter, rotating at 2600/min is 100°C. The results show 107°C and 104°C for the two iterations. The effect of friction induced temperature, changes the width of the contact area between the seal and the shaft, and significantly reduces the contact pressure.
文摘In this paper the behavior of an O-ring made of NBR rubber was investigated under extreme conditions. The effect of the extreme initial compression, operating pressure and extreme temperature conditions were examined. The rubber material was tested in simple tension, pure shear and equibiaxial tension modes complemented with a Dynamic Mechanical Thermal Analysis (DMTA) to capture the viscoelastic behavior of the material. For the investigation, a large-strain viscoelastic material model was developed by the authors, to take into account the large deformations caused by extreme conditions. Insufficient space during installation causes extreme initial compression consequently leading the material to crack on the contacting outer surfaces. It was found that the excessive strain and friction induced shear stress contributes primarily to this phenomenon. Extreme operating pressure causes the seal to penetrate into the gap between the shaft and the housing. This behavior damages the material and cracks appear on the seal. High strain areas were found in the proximity of the gap in the material. The analysis of the extreme operating temperature showed that during cooling the O-ring can completely loose its ability to seal at -70°C. There are three contributing factors: the speed of cooling, the temperature and the coefficient of thermal expansion.
