Friction stir processing(FSP)is a novel solid state technique to synthesize metal matrix composites.In the present work,an attempt has been made to synthesize AZ31/TiC magnesium matrix composites using FSP and to anal...Friction stir processing(FSP)is a novel solid state technique to synthesize metal matrix composites.In the present work,an attempt has been made to synthesize AZ31/TiC magnesium matrix composites using FSP and to analyze the microstructure using scanning electron microscopy.A groove was prepared on 6 mm thick AZ31 magnesium alloy plates and compacted with TiC particles.The width of the groove was varied to result in four different volume fraction of TiC particles(0,6,12 and 18 vol.%).A single pass FSP was carried out using a tool rotational speed of 1200 rpm,traverse speed of 40 mm/min and an axial force of 10 kN.Scanning electron microscopy was employed to study the microstructure of the synthesized composites.The results indicated that TiC particles were distributed uniformly in the magnesium matrix without the formation of clusters.There was no interfacial reaction between the magnesium matrix and the TiC particle.TiC particles were properly bonded to the magnesium matrix.展开更多
Utilizing fly ash(FA)as reinforcement for magnesium matrix composites(MMCs)brings down the production cost and the land pollution.Magnesium alloy AZ31 was reinforced with FA particles(10 vol.%)successfully by two diff...Utilizing fly ash(FA)as reinforcement for magnesium matrix composites(MMCs)brings down the production cost and the land pollution.Magnesium alloy AZ31 was reinforced with FA particles(10 vol.%)successfully by two different processing methods namely conventional stir casting and friction stir processing(FSP).The microstructural features were observed using optical microscope,scanning electron microscope and electron backscatter diffraction.The sliding wear behavior was tested using a pin-on-disc wear apparatus.The stir cast composite showed inhomogeneous particle dispersion and coarse grain structure.Some of the FA particles decomposed and reacted with the matrix alloy to produce undesirable compounds.Conversely,FSP composite showed superior particle dispersion and fine,equiaxed grains by dynamic recrystallization.FA particles encountered disintegration but there was no interfacial reaction.FSP composite demonstrated higher strengthening and wear resistance to that of stir cast composite.The morphology of the worn surface and the wear debris were studied in detail.展开更多
The influence of overlap multi-pass friction stir processing on the microstructure and the mechanical properties, in particular, strength, ductility and hardness of die cast A1-7Si-3Cu aluminum alloy was investigated....The influence of overlap multi-pass friction stir processing on the microstructure and the mechanical properties, in particular, strength, ductility and hardness of die cast A1-7Si-3Cu aluminum alloy was investigated. It was observed that increase in the number of overlap passes friction stir processing resulted in significant refinement and redistribution of aluminum silicon eutectic phase and elimination of casting porosities. The microstructural refinement by the friction stir processing not only increases the ultimate tensile strength from 121 to 273 MPa, but also increases the ductility as observed by the increase in fracture strain from 1.8% to 10%. Analysis of the fractured surface reveals that the microstructural refinement obtained by friction stir processing plays a vital role in transforming the fracture mode from completely mixed mode to the ductile mode of the fracture with increasing number of passes. The change in the size, shape, morphology and distribution of eutectic silicon particles and elimination of the porosities are the main reasons for the increases in tensile strength and ductility due to friction stir processing.展开更多
文摘Friction stir processing(FSP)is a novel solid state technique to synthesize metal matrix composites.In the present work,an attempt has been made to synthesize AZ31/TiC magnesium matrix composites using FSP and to analyze the microstructure using scanning electron microscopy.A groove was prepared on 6 mm thick AZ31 magnesium alloy plates and compacted with TiC particles.The width of the groove was varied to result in four different volume fraction of TiC particles(0,6,12 and 18 vol.%).A single pass FSP was carried out using a tool rotational speed of 1200 rpm,traverse speed of 40 mm/min and an axial force of 10 kN.Scanning electron microscopy was employed to study the microstructure of the synthesized composites.The results indicated that TiC particles were distributed uniformly in the magnesium matrix without the formation of clusters.There was no interfacial reaction between the magnesium matrix and the TiC particle.TiC particles were properly bonded to the magnesium matrix.
文摘Utilizing fly ash(FA)as reinforcement for magnesium matrix composites(MMCs)brings down the production cost and the land pollution.Magnesium alloy AZ31 was reinforced with FA particles(10 vol.%)successfully by two different processing methods namely conventional stir casting and friction stir processing(FSP).The microstructural features were observed using optical microscope,scanning electron microscope and electron backscatter diffraction.The sliding wear behavior was tested using a pin-on-disc wear apparatus.The stir cast composite showed inhomogeneous particle dispersion and coarse grain structure.Some of the FA particles decomposed and reacted with the matrix alloy to produce undesirable compounds.Conversely,FSP composite showed superior particle dispersion and fine,equiaxed grains by dynamic recrystallization.FA particles encountered disintegration but there was no interfacial reaction.FSP composite demonstrated higher strengthening and wear resistance to that of stir cast composite.The morphology of the worn surface and the wear debris were studied in detail.
文摘The influence of overlap multi-pass friction stir processing on the microstructure and the mechanical properties, in particular, strength, ductility and hardness of die cast A1-7Si-3Cu aluminum alloy was investigated. It was observed that increase in the number of overlap passes friction stir processing resulted in significant refinement and redistribution of aluminum silicon eutectic phase and elimination of casting porosities. The microstructural refinement by the friction stir processing not only increases the ultimate tensile strength from 121 to 273 MPa, but also increases the ductility as observed by the increase in fracture strain from 1.8% to 10%. Analysis of the fractured surface reveals that the microstructural refinement obtained by friction stir processing plays a vital role in transforming the fracture mode from completely mixed mode to the ductile mode of the fracture with increasing number of passes. The change in the size, shape, morphology and distribution of eutectic silicon particles and elimination of the porosities are the main reasons for the increases in tensile strength and ductility due to friction stir processing.
