Particle size distribution of 12-500 nm was measured at Mt. Waliguan, China Global Atmosphere Watch Baseline Observatory, from Aug. in 2005 to May in 2007.72-hr back-trajectories at 100-m arrival height above ground l...Particle size distribution of 12-500 nm was measured at Mt. Waliguan, China Global Atmosphere Watch Baseline Observatory, from Aug. in 2005 to May in 2007.72-hr back-trajectories at 100-m arrival height above ground level for the same period were calculated at 6：00, 12：00, and 21：00 （Beijing Time） for each day using the Hybrid Single-Particle Lagrangian Integrated Trajectory （HYSPLIT-4） model developed by NOAA/ARL. It was found that air mass sources significantly impact particle number concentration and size distribution at Mt. Waliguan. Cluster analysis of back-trajectories show that higher Aitken mode particle number concentration was observed when air masses came from or passed by the northeastern section of Mt. Waliguan, with short trajectory length. High number concentration of nucleation mode was associated with air masses from clean regions, with long trajectory length.展开更多
This paper presents a modified method of discontinuous deformation analysis(DDA). In the presented method, open-close iteration may not be needed, small penetration is permitted among blocks, and springs are added bet...This paper presents a modified method of discontinuous deformation analysis(DDA). In the presented method, open-close iteration may not be needed, small penetration is permitted among blocks, and springs are added between contacting block pairs only when a penetration takes place. The three contact patterns(i.e. sliding, locking and opening) in original DDA method are not involved, and the recognition of these contact patterns and treatment of transformation among patterns are not required either,signi fi cantly saving the computing time. In a convex to concave contact, there are two candidate entrance edges which may cause uncertainty. In this case, we propose the angle bisector criterion to determine the entrance edge. The spring stiffness is much larger than Young's modulus in the original DDA, however we fi nd that the correct results can still be obtained when it is much smaller than Young's modulus. Finally,the penetrations by using penalty method and augmented Lagrangian method are compared. Penetration of the latter is 1/4 of the former. The range of spring stiffness for the latter is wider than the former,being 0.01-1 of the former. Both methods can lead to correct contact forces.展开更多
基金sponsored by National Key Development Program for Fundamental Research (973 Program) Project(Nos.2006CB403703 and 2006CB403701)
文摘Particle size distribution of 12-500 nm was measured at Mt. Waliguan, China Global Atmosphere Watch Baseline Observatory, from Aug. in 2005 to May in 2007.72-hr back-trajectories at 100-m arrival height above ground level for the same period were calculated at 6：00, 12：00, and 21：00 （Beijing Time） for each day using the Hybrid Single-Particle Lagrangian Integrated Trajectory （HYSPLIT-4） model developed by NOAA/ARL. It was found that air mass sources significantly impact particle number concentration and size distribution at Mt. Waliguan. Cluster analysis of back-trajectories show that higher Aitken mode particle number concentration was observed when air masses came from or passed by the northeastern section of Mt. Waliguan, with short trajectory length. High number concentration of nucleation mode was associated with air masses from clean regions, with long trajectory length.
基金supported by CRSRI Open Research Program (No.CKWV2014206/KY)the National Basic Research Program of China (No.2011CB710603)
文摘This paper presents a modified method of discontinuous deformation analysis(DDA). In the presented method, open-close iteration may not be needed, small penetration is permitted among blocks, and springs are added between contacting block pairs only when a penetration takes place. The three contact patterns(i.e. sliding, locking and opening) in original DDA method are not involved, and the recognition of these contact patterns and treatment of transformation among patterns are not required either,signi fi cantly saving the computing time. In a convex to concave contact, there are two candidate entrance edges which may cause uncertainty. In this case, we propose the angle bisector criterion to determine the entrance edge. The spring stiffness is much larger than Young's modulus in the original DDA, however we fi nd that the correct results can still be obtained when it is much smaller than Young's modulus. Finally,the penetrations by using penalty method and augmented Lagrangian method are compared. Penetration of the latter is 1/4 of the former. The range of spring stiffness for the latter is wider than the former,being 0.01-1 of the former. Both methods can lead to correct contact forces.
