铁浴条件下电炉粉尘球团的熔融与分离行为

为了提高对含锌电弧炉粉尘(EAFD)的利用效率,实验研究EAFD球团在铁浴条件下的还原熔化行为。定义铁液滴球形度作为判断其凝聚的标准,然后探讨铁液滴直径和球形度之间随时间变化的关系。根据实验最终建立EAFD颗粒的熔化和分离行为。结果表明,在铁浴条件下,EAFD球团的Zn去除率在5.0 min时达到99%以上,但在15.0 min时金属渣分离还没有完成。由于成分的波动,在EAFD球团中形成几个区域的液态渣,然后液态渣不断增加,直到球团完全熔化。球形度>65%、直径>500μm的Fe液滴的数量随着时间的推移而减少,大直径的Fe液滴先完成分离。渣铁分离过程如下:在布朗运动下Fe液滴在渣中形成,之后Fe液滴直径在马兰戈尼效应下增加,Fe液滴在渣中下降速度符合斯托克斯定律。

Effect of carbon species on the reduction and melting behavior of boron-bearing iron concentrate/carbon composite pellets

Iron nugget and boron-rich slag can be obtained in a short time through high-temperature reduction of boron- bearing iron concentrate by carbonaceous material, both of which are agglomerated together as a carbon composite pellet. This is a novel flow sheet for the comprehensive utilization of boron-bearing iron concentrate to produce a new kind of man-made boron ore. The effect of reducing agent species （i.e., carbon species） on the reduction and melting process of the composite pellet was investigated at a laboratory scale in the present work. The results show that, the reduction rate of the composite pellet increases from bituminite, anthracite, to coke at temperatures ranging from 950 to 1300~C. Reduction temperature has an important effect on the microstructure of reduced pellets. Carbon species also affects the behavior of reduced metallic iron particles. The anthracite-bearing composite pellet melts faster than the bituminite- bearing composite pellet, and the coke-bearing composite pellet cannot melt due to the high fusion point of coke ash. With anthracite as the reducing agent, the recovery rates of iron and boron are 96.5% and 95.7%, respectively. This work can help us get a further understanding of the new process mechanism.

Basic properties of steel plant dust and technological properties of direct reduction

Basic physicochemical properties of the dust from Laiwu Iron and Steel Co. Ltd. were studied. It is found that C, Zn, K, Na, etc. exist in the fabric filter dust, off gas （OG） sludge, fine ash in converter, and electrical field dust in sinter. Among these, OG sludge gives the finest particle, more than 90% of which is less than 2.51 mm. The dust can lead to a serious negative influence on the production of sintering and blast furnaces （BF） if it is recycled in sintering. The briquette and reduction experimental results showed that the qualified strength could be obtained in the case of 8wt% molasses or 4wt% QT-10 added as binders. Also, more than 75% of metallization ratio, more than 95% of dezincing ratio, as well as more than 80% of K and Na removal rates were achieved for the briquettes kept at 1250℃ for 15 min during the direct reduction process. SEM observation indicated that the rates of indirect reduction and carbonization became dominating when the bri-quettes were kept at 1250℃ for 6 min.

The mechanism and products for co-thermal extraction of biomass and low-rank coal with NMP

The high-value utilization of low-rank coal would allow for expanding energy sources,improving energy efficiencies,and alleviating environmental issues.In order to use low-rank coal effectively,the hypercoals(HPCs)were co-extracted from two types of low-rank coal and biomass via N-methyl-2-purrolidinone(NMP)under mild conditions.The structures of the HPCs and residues were characterized by proximate and ultimate analysis,Raman spectra,and Fourier transform infrared(FT-IR)spectra.The carbon structure changes within the raw coals and HPCs were discussed.The individual thermal dissolution of Xibu(XB)coal,Guandi(GD)coal,and the biomass demonstrated that the biomass provided the lowest thermal dissolution yield Y1 and the highest thermal soluble yield Y2 at 280℃,and the ash content of three HPCs decreased as the extraction temperature rose.Co-thermal extractions in NMP at various coal/biomass mass ratios were performed,demonstrating a positive synergic effect for Y2 in the whole coal/biomass mass ratios.The maximum value of Y2 was 52.25wt% for XB coal obtained with a XB coal/biomass of 50wt% biomass.The maximum value of Y2 was 50.77wt% for GD coal obtained with a GD coal/biomass of 1:4.The difference for the optimal coal/biomass mass ratios between XB and GD coals could be attributed to the different co-extraction mechanisms for this two type coals.

Carbothermic reduction characteristics of ludwigite and boron–iron magnetic separation

Ludwigite is a kind of complex iron ore containing boron, iron, and magnesium, and it is the most promising boron resource in China. Selective reduction of iron oxide is the key step for the comprehensive utilization of ludwigite. In the present work, the reduction mechanism of ludwigite was investigated. The thermogravimetry and differential scanning calorimetry analysis and isothermal reduction of ludwigite/coal composite pellet were performed. Ludwigite yielded a lower reduction starting temperature and a higher final reduction degree compared with the traditional iron concentrates. Higher specific surface area and more fine cracks might be the main reasons for the better reducibility of ludwigite. Reducing temperature highly affected the reaction fraction and microstructure of the reduced pellets, which are closely related to the separation degree of boron and iron. Increasing reducing temperature benefited the boron and iron magnetic separation. Optimum magnetic separation results could be obtained when the pellet was reduced at 1300°C. The separated boron-rich non-magnetic concentrate presented poor crystalline structure, and its extraction efficiency for boron reached 64.3%. The obtained experimental results can provide reference for the determination of the comprehensive utilization flow sheet of ludwigite.

Mathematical model of the direct reduction of dust composite pellets containing zinc and iron

Direct reduction of dust composite pellets containing zinc and iron was examined by simulating the conditions of actual production process of a rotary hearth furnace （RHF） in laboratory. A mathematical model was constructed to study the reduction kinetics of iron oxides and ZnO in the dust composite pellets. It was validated by comparing the calculated values with experimental results. The effects of furnace temperature, pellet radius, and pellet porosity on the reduction were investigated by the model. It is shown that furnace temperature has obvious influence on both of the reduction of iron oxides and ZnO, but the influence of pellet radius and porosity is much smaller. Model calculations suggest that both of the reduction of iron oxides and ZnO are under mixed control with interface reactions and Boudouard reaction in the early stage, but only with interface reactions in the later stage.

Preparation of CaO-containing carbon pellets from coking coal and calcium oxide:Effects of temperature,pore distribution and carbon structure on compressive strength in pyrolysis furnace

CaO-containing carbon pellets(CCCP)were successfully prepared from well-mixed coking coal(CC)and calcium oxide(CaO)and roasted at different pyrolysis temperatures.The effects of temperature,pore distribution,and carbon structure on the compressive strength of CCCP was investigated in a pyrolysis furnace(350-750℃).The results showed that as the roasting temperature increased,the compressive strength also increased and furthermore,structural defects and imperfections in the carbon crystallites were gradually eliminated to form more organized char structures,thus forming high-ordered CC.Notably,the CCCP preheated at 750℃exhibited the highest compressive strength.A positive relationship between the compressive strength and pore-size homogeneity was established.A linear relationship between the com-pressive strength of the CCCP and the average stack height of CC was observed.Additionally,a four-stage caking mechanism was developed.

Innovative method for boron extraction from iron ore containing boron

A novel process for boron enrichment and extraction from ludwigite based on iron nugget technology was proposed. The key steps of this novel process, which include boron and iron separation, crystallization of boron-rich slag, and elucidation of the boron extraction be- havior of boron-rich slag by acid leaching, were performed at the laboratory. The results indicated that 95.7% of the total boron could be en- riched into the slag phase, thereby forming a boron-rich slag during the iron and slag melting separation process. Suanite and kotoite were observed to be the boron-containing crystalline phases, and the boron extraction properties of the boron-rich slag depended on the amounts and grain sizes of these minerals. When the boron-rich slag was slowly cooled to 1100℃, the slag crystallized well and the efficiency of ex- traction of boron （EEB） of the slag was the highest observed in the present study. The boron extraction property of the slow-cooled bo- ron-rich slag obtained in this study was much better than that of szaibelyite ore under the conditions of 80% of theoretical sulfuric acid amount, leaching time of 30 min, leaching temperature of 40℃ ,and liquid-to-solid ratio of 8 mL/g.

Reduction–melting behaviors of boron-bearing iron concentrate/carbon composite pellets with addition of CaO

Although the total amount of boron resources in China is high, the grades of these resources are low. The authors have already proposed a new comprehensive utilization process of boron-bearing iron concentrate based on the iron nugget process. The present work describes a further optimization of the conditions used in the previous study. The effects of CaO on the reduction-melting behavior and properties of the boron-rich slag are presented. CaO improved the reduction of boron-bearing iron concentrate/carbon composite pellets when its content was less than lwt%. Melting separation of the composite pellets became difficult with the CaO content increased. The sulfur content of the iron nugget gradually decreased from 0.16wt% to 0.046wt% as the CaO content of the pellets increased from 1wt% to 5wt%. CaO negatively affected the iron yield and boron extraction efficiency of the boron-rich slag. The mineral phase evolution of the boron-rich slag during the reduction-melting separation of the composite pellets with added CaO was also deduced.

Carbothermic reduction behaviors of Ti–Nb-bearing Fe concentrate from Bayan Obo ore in China

To support the development of technology to utilize low-grade Ti-Nb-bearing Fe concentrate, the reduction of the concentrate by coal was systematically investigated in the present paper. A liquid phase formed when the Ti Nb-bearing Fe concentrate/coal composite pel- let was reduced at temperatures greater than 1100℃. The addition of CaCO3 improved the reduction rate when the slag basicity was less than 1.0 and inhibited the formation of the liquid phase. Mechanical milling obviously increased the metallization degree compared with that of the standard pellet when reduced under the same conditions. Evolution of the mineral phase composition and microstructure of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet at 1100~C were analyzed by X-ray diffraction and scanning electron microsco- py-energy-dispersive spectroscopy. The volume shrinkage value of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet with a basicity of 1.0 was approximately 35.2% when the pellet was reduced at 1100℃ for 20 min, which enhanced the external heat transfer to the lower layers when reduced in a practical rotary hearth furnace. The present work provides key parameters and mechanism understanding for the development of carbothermic reduction technology of a Ti-Nb-bearing Fe concentrate incorporated in a pyrometallurgical utilization flow sheet.

A New Post-hoc Flat Field Measurement Method for the Solar X-Ray and Extreme Ultraviolet Imager Onboard the FengYun-3E Satellite

Extreme ultraviolet(EUV)observations are widely used in solar activity research and space weather forecasting since they can observe both the solar eruptions and the source regions of the solar wind.Flat field processing is indispensable to remove the instrumental non-uniformity of a solar EUV imager in producing high-quality scientific data from original observed data.FengYun-3E(FY-3E)is a meteorological satellite operated in a Sunsynchronous orbit,and the routine EUV imaging data from the Solar X-ray and Extreme Ultraviolet Imager(X-EUVI)onboard FY-3E has the characteristic of concentric rotation.Taking advantage of the concentric rotation,we propose a post-hoc flat field measurement method for its EUV 195A channel in this paper.This method removes the small-scale and time-varying component of coronal activities by taking the median value for each pixel along the time axis of a concentric rotation data cube,and then derives the large-scale and invariable component of the quiet coronal radiation,and finally generates a flat field image.The flat field can be generated with cadences from hundreds of minutes(one orbit)to several days.Higher flat field accuracy can be achieved by employing more data.Further analysis shows that our method is able to measure the instrumental spot-like nonuniformity possibly caused by contamination on the detector,which mostly disappears after the in-orbit selfcleaning process.It can also measure the quasi-periodic grid-like non-uniformity,possibly from the obscuration of the support mesh on the rear filter.After flat field correction,these instrumental non-uniformities from the original data are effectively removed.Moreover,the X-EUVI 195A data after dark and flat field corrections are consistent with the 193A imaging data from the Atmospheric Imaging Assembly onboard the Solar Dynamics Observatory,verifying the suitability of the method.The post-hoc method does not occupy observation time,which is advantageous for space weather operations.Our method is not only suitable for FY-3E/X-EUVI but also a candidate method for the flat field measurement of future solar EUV telescopes.

A Collaborative Filtering Recommendation Algorithm Based on the Difference and the Correlation of Users’Ratings

The traditional similarity algorithm in collaborative filtering mainly pay attention to the similarity or correlation of users’ratings,lacking the consideration of difference of users’ratings.In this paper,we divide the relationship of users’ratings into differential part and correlated part,proposing a similarity measurement based on the difference and the correlation of users’ratings which performs well with non-sparse dataset.In order to solve the problem that the algorithm is not accurate in spare dataset,we improve it by prefilling the vacancy of rating matrix.Experiment results show that this algorithm improves significantly the accuracy of the recommendation after prefilling the rating matrix.

Exploring a new path of green and efficient utilization of sinter return fine to produce composite pellets

Efficient utilization of sinter return fine is an important measure to reduce cost,increase efficiency,save energy and reduce emission.A new path of green and efficient utilization of return fine was proposed to produce composite pellets.The metallurgical properties of composite pellets under the condition of hydrogen-rich blast furnace were studied.The experimental results indicate that the coated concentrate was consolidated for the composite pellets through normal Fe_(2)O_(3) recrystallization.Near the surface of core return fine,the liquid phase formed due to its low-melting point,assimilated the adjacent concentrate,and then consolidated with the temperature decreasing.Compared with regular pellets,the com-pressive strength and reduction swelling index of composite pellets were decreased,but the reducibility index and softening-melting properties were improved.In addition,the reduction degradation index of composite pellets was sig-nificantly higher than that of sinter.Therefore,adding composite pellets was conducive to indirect reduction in blast furnace,reducing fuel ratio and improving production efficiency.According to the effect of the roasting system on the metallurgical properties,the roasting temperature and time were determined as 1250℃and 30 min,respectively.The composite pellets can be produced under the traditional pelletizing process.

Improving mathematical model of burden distribution and correcting chute angle to cope with fluctuation of stock line

Accurate evaluations of the burden distribution are of critical importance to stabilize the operation of blast furnace.The mathematical model and discrete element method(DEM)are two attractive methods for predicting burden distribution.Based on DEM,the initial velocities of the pellet,sinter,and coke were calculated,and the velocity attenuations of the above three particles between the burden and the chute were analyzed.The initial velocity and velocity attenuation were applied to a mathematical model for improving the accuracy.Additionally,based on the improved model,a scheme for rectifying the chute angles was proposed to address the fluctuation of the stock line and maintain a stable burden distribution.The validity of the scheme was confirmed via a stable burden distribution under different stock lines.The mathematical model has been successfully applied to evaluate the online burden distribution and cope with the fluctuation of the stock line.

Effect of atmosphere and basicity on softening-melting behavior of primary slag formation in cohesive zone

The softening-melting characteristics of ferrous burden play a crucial role in the thickness and position of the cohesive zone.The influence of the basicity and experimental atmosphere on the softening-melting behavior of primary slag under slag-coke interaction was investigated using in situ visualization method.The mechanism was analyzed using the FactSage software,X-ray diffraction,and electron probe microanalysis.The softening and melting temperatures of the samples increased with increasing basicity under different atmospheres.The difference between softening and melting temperatures is smaller in a H_(2) atmosphere than in a CO atmosphere;in H_(2) atmosphere,the range of softening zone in the cohesive zone was significantly thinner.The formed low-melting-point FeO-bearing phases decrease when H_(2) was used as the reducing agent.In addition,according to FactSage calculations,the high content of metallic iron reduced in the H_(2) atmosphere raised the softening temperature of the primary slag.It also narrowed and moved downward the cohesive zone due to an increase in softening and melting temperatures.Meanwhile,the increase in basicity promoted the decrease in liquid ratio and improved the permeability of cohesive zone.

Mathematical model of burden distribution in bell-less top blast furnace

The burden distribution in the shaft of blast furnace is known to affect the gas distribution,heat transfer,and chemical reactions inside the furnace.However,the internal layer structure of burden in the shaft cannot be directly measured.Hence,a mathematical model for evaluating burden profile and layer structure was established.A sensitivity analysis based on the model was implemented to elucidate the effect of some factors on the burden distribution,including the stockline height and the mass of central coke.The results show that the width of funnel zone widens with the increase in stockline height,and the mass percentage of ore to coke in this zone slightly increases.Besides,the mass of central coke shows a significant influence on the width of coke channel,and 2%of batch mass of coke is recommended to implement central coke charging operation.The model has been indirectly verified by the gas temperature in operating blast furnace and successfully applied to online evaluate burden distribution.

Softening and melting behaviors of ferrous burden in hydrogen-rich blast furnace cohesive zone

The changes in the softening and melting behaviors of ferrous burden in the cohesive zone and the characteristics of the slag–iron–coke interface in a blast furnace were investigated by simulating an actual blast furnace under hydrogen-rich conditions.According to the variation in the transient shrinkage of the burden under different atmospheres,the shrinkage start temperature of the sinter was higher than that of the pellets.The negative shrinkage rate of the pellets was greater than that of the sinter.Additionally,the softening start temperature in the blast furnace decreased under hydrogen-rich conditions,giving the blast furnace a broader range of softening zones.The softening start temperatures of the pellets and sinter decreased from 1102 to 949℃ and 1152 to 1080℃,respectively.The hydrogen-rich traditional blast furnace conditions narrowed the melting zone temperature range and shifted it toward the high-temperature zone,significantly improving the burden layer permeability.However,under the hydrogen-rich oxygen blast furnace conditions,there were a decrease in the melting start temperature,a shift of the melting zone location to the low-temperature zone,and an increase in the burden layer permeability and pressure difference.A comparison of the slag–iron–coke interface characteristics under different atmospheric conditions showed that the carbon content in metallic iron decreased under hydrogen-rich traditional blast furnace conditions compared with traditional blast furnace conditions.Contrastingly,under hydrogen-rich oxygen blast furnace conditions,the carbon content in metallic iron increased compared with oxygen blast furnace conditions.These findings provide guidance for the development of low-carbon ironmaking processes in blast furnaces.

Removal Mechanism of Zn,Pb and Alkalis from Metallurgical Dusts in Direct Reduction Process

The high-temperature tube furnace was applied to simulate the rotary hearth furnace （RHF） for the direct reduction of zinc-bearing dusts from steel plants. The removal mechanism of Zn, Pb and alkalis from cold bonded briquettes made by mixing metallurgical wastes, such as dust from bag house filter, OG sludge, fine converter ash and dust from the third electric field precipitator of the sinter strand, in various proportions was investigated. More than 70% of metallization rate, more than 95% of zinc removal rate, 80% of lead removal, as well as more than 80M of K and Na removal rates were achieved for the briquettes kept at 1473-1603 K for 15 min during the direct reduction process respectively. The soot generated in the direct reduction process was studied by chromatography, X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results suggested that the main phases of the soot were ZnO, KC1, NaC1 and 4ZnO · ZnC12 · 5H20. Furthermore, the content of Zn reached 64.2 %, which could be used as secondary resources for zinc making. It was concluded that KC1 and NaC1 in secondary dust resulted from the volatilization from the briquettes, whilst ZnO and PbO were produced by the oxidation of Zn or lead vapour from briquettes by direct reduction.

Softening and Melting Behavior of Ferrous Burden under Simulated Oxygen Blast Furnace Condition

The softening and melting behavior of sinter, pellet and mixed burden was researched through high tem- perature reaction tests under load simulating traditional blast furnace （T-BF） and oxygen blast furnace （OBF） condi- tions. The results indicated that compared with T-BF, the softening zone of sinter and pellet became wide, but the melting zone became narrow in OBF. The permeabilities of both sinter and pellet were improved in OBF. Under the condition of OBF, the temperature of softening zone of mixed burden was increased by 63 K, but the temperature of melting zone was decreased by 76 K. Therefore, the permeability of material layer was significantly improved. This was mainly caused by the change of the melting behavior of pellet. In addition, the quality Of dripping iron in OBF was much better than that of T-BF.

Microstructure evolution of coke under CO2 and H2O atmospheres

The microstructure of coke has an important influence on its thermal properties.The solution loss reactions of coke in CO2 and H2O atmospheres were investigated by in situ observation.The results showed that the isotropic components had a more vigorous reaction than the anisotropic components,and the solution loss reaction of the fine-grained mosaic structure was faster than that of the coarse-grained mosaic structure under the CO2 and H2O atmospheres.The coarse-grained mosaic structure and the flowing structure had a relatively higher anti-erosion ability in the CO2 atmosphere than in the H2O atmosphere,and there was no distinct difference in the solution loss of the isotropic structure under the CO2 and H2O atmospheres.The electron probe microanalysis showed that the Al-Si-Fe compounds in the carbon matrix had positive influence on the solution loss reaction of the anisotropic structure.The iron compounds were able to destroy the pore walls of coke and accelerate the solution loss rate of coke.