期刊文献+
共找到8篇文章
< 1 >
每页显示 20 50 100
工艺与微量元素对镍基合金焊接热影响区液化裂纹影响的研究进展 被引量:6
1
作者 栗卓新 王恒 +2 位作者 李杨 kim hee jin TILLMANN Wolfgang 《机械工程学报》 EI CAS CSCD 北大核心 2016年第6期37-45,共9页
镍基合金因其优异的耐高温和耐腐蚀性,广泛地应用在航空航天、核电及海洋采油等行业。基于镍基合金的重要性,研究其焊接热影响区(Heat-affected zone,HAZ)液化裂纹问题对于促进该问题的解决具有重要意义。焊接工艺的好坏直接影响到镍基... 镍基合金因其优异的耐高温和耐腐蚀性,广泛地应用在航空航天、核电及海洋采油等行业。基于镍基合金的重要性,研究其焊接热影响区(Heat-affected zone,HAZ)液化裂纹问题对于促进该问题的解决具有重要意义。焊接工艺的好坏直接影响到镍基合金焊接性能,是导致其HAZ液化裂纹的重要因素之一。采用热处理工艺,可以获得预期的组织和性能,以降低液化裂纹敏感性。同时,合金母材中微量元素影响晶界非平衡偏析行为,会导致HAZ液化裂纹的产生。从焊接工艺、热处理工艺及微量元素三个方面综述镍基合金焊接HAZ液化裂纹的最新进展,并对液化裂纹的测试方法进行总结,对未来的研究趋势进行展望。 展开更多
关键词 镍基合金 热影响区 液化裂纹 焊接 热处理 微量元素
下载PDF
不锈钢焊缝铁素体含量测试方法与精度的现状及进展 被引量:7
2
作者 栗卓新 焦俊 kim hee jin 《机械工程学报》 EI CAS CSCD 北大核心 2014年第12期89-96,共8页
铁素体含量对不锈钢焊缝的耐蚀、韧性、强度等性能有重要影响,准确测量或预测十分重要.铁素体含量的测试与预测方法有很多种,最常使用的是图谱法和磁测法,介绍这两种方法的最新进展.在不同实验室制备及测量试样、试样表面是否进行处理... 铁素体含量对不锈钢焊缝的耐蚀、韧性、强度等性能有重要影响,准确测量或预测十分重要.铁素体含量的测试与预测方法有很多种,最常使用的是图谱法和磁测法,介绍这两种方法的最新进展.在不同实验室制备及测量试样、试样表面是否进行处理等都会影响测试与预测结果的精度.铁素体数(Ferrite number,FN)小于5时,不同实验室之间图谱法预测结果的波动是平均值的±60%,铁素体数在15~35时,图谱法预测结果的波动是平均值的±30%.磁测法测量的波动是平均值的±20%,小于图谱预测法,是目前较精确的测试方法.新的预测方法考虑了元素之间相互作用和冷却速度等因素对铁素体含量的影响,提高了预测的精度.针对铁素体数测试结果不可避免的波动问题,提出目标范围这一概念来解决焊材设计者与使用者对测试结果产生的分歧. 展开更多
关键词 不锈钢焊缝 铁素体含量 铁素体数 波动
下载PDF
690 MPa级以上高强钢焊接熔敷金属微观组织及其联合贝氏体的研究进展 被引量:3
3
作者 栗卓新 苏小虎 +1 位作者 李红 kim hee jin 《中国材料进展》 CAS CSCD 北大核心 2019年第12期1169-1176,共8页
690 MPa级以上高强钢的发展和工程应用受限于缺乏与其强韧性相匹配的焊接材料,其根本原因是以针状铁素体为主的690 MPa级以下高强钢熔敷金属的强韧化理论已经不能指导新一代高强钢焊接熔敷金属的设计。因此,解决该问题的关键是寻求最佳... 690 MPa级以上高强钢的发展和工程应用受限于缺乏与其强韧性相匹配的焊接材料,其根本原因是以针状铁素体为主的690 MPa级以下高强钢熔敷金属的强韧化理论已经不能指导新一代高强钢焊接熔敷金属的设计。因此,解决该问题的关键是寻求最佳的熔敷金属微观组织结构。综述了690 MPa级以上高强钢焊接熔敷金属中出现的联合贝氏体和其它各类微观组织对其强韧性的影响。其中,由不同形貌贝氏体相和针状铁素体相组成的复相分割结构可使焊接熔敷金属实现良好的强韧性匹配;然而,联合贝氏体作为下贝氏体的一种,其大尺寸的特点会显著降低高强钢焊接熔敷金属的强韧性;此外,可以通过物理冶金改善高强钢焊接熔敷金属的性能。 展开更多
关键词 高强钢 微观组织 联合贝氏体 焊接熔敷金属 强韧性
下载PDF
熔化极气体保护焊导电嘴载流磨损及使用寿命的研究进展 被引量:1
4
作者 栗卓新 丛兴 +1 位作者 李红 kim hee jin 《材料导报》 EI CAS CSCD 北大核心 2020年第19期19128-19133,19151,共7页
现代制造业要求焊接技术向智能化、连续化、绿色化发展,目前熔化极气体保护焊焊接过程中焊丝对导电嘴的磨损率过大,频繁地停工更换和清理零部件限制了熔化极气体保护焊自动化焊接的发展。电接触条件下的载流磨损是导致材料磨损率过大的... 现代制造业要求焊接技术向智能化、连续化、绿色化发展,目前熔化极气体保护焊焊接过程中焊丝对导电嘴的磨损率过大,频繁地停工更换和清理零部件限制了熔化极气体保护焊自动化焊接的发展。电接触条件下的载流磨损是导致材料磨损率过大的重要原因,主要体现在两个方面:(1)电接触产生焦耳热,使环境温度大幅提高,局部温度甚至超过500℃,造成电接触材料发生软化;(2)电接触点的不断运动和变化导致产生微观电弧,造成局部材料的剧烈熔融和氧化。因电接触造成的电气磨损与机械磨损相互加剧,大幅缩短了导电嘴器件的使用寿命。接触电阻是产生焦耳热和微观电弧的关键因素,镀铜钢焊丝与导电嘴之间的接触电阻值约为1.6 mΩ,而对于无镀铜钢焊,该值提高到约2.5 mΩ。导电嘴使用寿命随接触电阻、焊接电流、送丝速度增大而缩短;法向接触载荷一方面增大机械磨损,另一方面减少电气磨损,因此对导电嘴寿命有着复杂影响。高强度、高导电性导电嘴材料有利于延长导电嘴使用寿命,利用双相析出沉淀强化的Cu-Cr-Zr系铜合金能在显著提高材料强度的同时尽可能地减少因合金固溶导致的电导率损失,与此同时,石墨基、粉末冶金及复合材料导电嘴也有一定的实用性和研究价值。光洁平整的焊丝表面有利于延长导电嘴使用寿命,在无镀铜焊丝表面制备润滑性涂层能进一步提升导电嘴磨损性能。由于焊接条件的特殊性,表面涂层需兼具高温稳定性、高导电性等特征,具有表面效应和小尺寸效应的固体润滑剂在这方面具有极大的优势和应用前景。本文综述了熔化极气体保护焊导电嘴载流磨损机理的研究进展,从工艺参数、导电嘴材料、焊丝表面状态等方面分析了影响导电嘴载流磨损的因素和延长导电嘴寿命的可行方法,对减少导电嘴磨损,延长其寿命,推动机器人自动化焊接和无镀铜实心焊丝研发制造具有一定的指导意义。 展开更多
关键词 熔化极气体保护焊 工艺性能 导电嘴寿命 载流磨损
下载PDF
氧含量及夹杂物对高强钢金属芯焊丝E120C-K4熔敷金属冲击韧性的影响 被引量:1
5
作者 苏小虎 栗卓新 +3 位作者 马思鸣 李红 张天理 kim hee jin 《材料导报》 EI CAS CSCD 北大核心 2020年第11期11049-11052,共4页
本工作通过改变保护气体配比和Zr-Ti、Ti-B微合金化研究了金属芯焊丝E120C-K4熔敷金属中的氧含量及夹杂物对其微观组织和冲击韧性的影响。研究表明:在金属芯焊丝E120C-K焊接熔敷金属中,随着氧含量的增加,熔敷金属组织晶粒尺寸增大,粒状... 本工作通过改变保护气体配比和Zr-Ti、Ti-B微合金化研究了金属芯焊丝E120C-K4熔敷金属中的氧含量及夹杂物对其微观组织和冲击韧性的影响。研究表明:在金属芯焊丝E120C-K焊接熔敷金属中,随着氧含量的增加,熔敷金属组织晶粒尺寸增大,粒状贝氏体含量增加,夹杂物尺寸增大、含量增加,熔敷金属的冲击韧性明显降低;添加微量Zr-Ti微合金的熔敷金属中夹杂物面积在单位面积所占比例降低,夹杂物的平均粒径减小,尺寸集中于0.4~0.7μm之间,为针状铁素体(AF)形核提供了潜在质点,从而提高了熔敷金属的冲击吸收功。 展开更多
关键词 氧含量 微合金化 夹杂物 熔敷金属 冲击韧性
下载PDF
Feasibility assessment of phenotyping cotton fiber maturity using infrared spectroscopy and algorithms for genotyping analyses 被引量:1
6
作者 kim hee jin LIU Yongliang +1 位作者 FANG David D. DELHOM Christopher D. 《Journal of Cotton Research》 2019年第1期44-55,共12页
Background:Cotton fiber maturity is an important property that partially determines the processing and performance of cotton.Due to difficulties of obtaining fiber maturity values accurately from every plant of a gene... Background:Cotton fiber maturity is an important property that partially determines the processing and performance of cotton.Due to difficulties of obtaining fiber maturity values accurately from every plant of a genetic population,cotton geneticists often use micronaire(MIC) and/or lint percentage for classifying immature phenotypes from mature fiber phenotyp es although they are complex fiber traits.The recent development of an algorithm for determining cotton fiber maturity(MIR)from Fourier transform infrared(FT-IR)spectra explores a novel way to measure fiber maturity efficiently and accurately.However,the algorithm has not been tested with a genetic population consisting of a large number of progeny pla,nts.Results:The merits and limits of the MIC-or lint percentage-bas ed phenotyping method were demonstrated by comparing the observed phenotypes with the predicted phenotypes based on their DNA marker genotypes in a genetic population consisting of 708 F2 plants with various fiber maturity.The observed MIC-based fiber phenotypes matched to the predicted phenotypes better than the observed lint percenta ge-based fiber phenotypes.The lint percentage was obtained from each of F2 plants,whereas the MIC values were unable to be obtained from the entire population since certain F2 plants produced insufficient fiber mass for their measurements.To test the feasibiility of cotton fiber infrared maturity(MIR)as a viable phenotyping tool for genetic analyses,we me asured FT-IR spectra from the second population composed of 80 F2 plants with various fiber maturities,determined MIR values using the algorithms,and compared them with their genotypes in addition to other fiber phenotypes.The results showed that MIR values were successfully obtained from each of the F2 plants,and the observed MIR-based phenotypes fit well to the predicted phenotypes based on their DNA marker genotypes as well as the observed phenotypes based on a combination of MIC and lint percentage.Conclusions:The M,R value obtained from FT-IR spectra of cotton fibers is able to accurately assess fiber maturity of all plants of a population in a quantitative way.The technique provides an option for cotton geneticists to determine fiber maturity rapidly and efficiently. 展开更多
关键词 Attenuated total reflection Fourier transform infrared spectroscopy Cotton FIBER MATURITY CRYSTALLINITY IMMATURE FIBER (im) mutant
下载PDF
Fourier transform infrared spectral features of plant biomass components during cotton organ development and their biological implications
7
作者 HE Zhongqi LIU Yongliang +2 位作者 kim hee jin TEWOLDE Haile ZHANG Hailin 《Journal of Cotton Research》 2022年第2期130-142,共13页
Background:The majority of attenuated total reflection Fourier transform infrared(ATR FT-IR)investigations of cotton are focused on the fiber tissue for biological mechanisms and understanding of fiber development and... Background:The majority of attenuated total reflection Fourier transform infrared(ATR FT-IR)investigations of cotton are focused on the fiber tissue for biological mechanisms and understanding of fiber development and maturity,but rarely on other cotton biomass comp on ents.This work examined in detail the ATR FT-IR spectral features of various cott on tissues/organs at reproductive and maturation stages,an a lyzed and discussed their biological implications.Results:The ATR FT-IR spectra of these tissues/organs were an a lyzed and compared with the focus on the lower wavenumber fingerprinting range.Six outstanding FT-IR bands at 1730,1620,1525,1235,1050 and 895 cm^(-1) represented the major C=O stretching,protein Amide I,Amide II,the O-H/N-H deformation,the total C-O-C stretching and the β-glycosidic linkage in celluloses,respectively,and impacted differently between these organs with the two growth stages.Furthermore,the band intensity at 1620,1525,1235,and 1050 cm^(-1) were exclusively and significantly correlated to the levels of protein(Amide I bond),protein(Amide II bond),cellulose,and hemicellulose,respectively,whereas the band at 1730 cm^(-1) was negatively correlated with ash content.Conclusions:The resulting observations indicated the capability of ATR FT-IR spectroscopy for monitoring changes,transportation,and accumulation of the major chemical components in these tissues over the cotton growth period.In other words,this spectral technology could be an effective tool for physiological,biochemical,and morphological research related to cotton biology and development. 展开更多
关键词 COTTON Fourier transform infrared spectroscopy FIBER CELLULOSE PROTEIN Plant tissue
下载PDF
药芯组成及工艺参数对ENiCrMo3T0-4药芯焊丝气孔敏感性的影响 被引量:4
8
作者 王恒 栗卓新 +1 位作者 Wolfgang Tillmann kim hee jin 《稀有金属材料与工程》 SCIE EI CAS CSCD 北大核心 2018年第4期1205-1209,共5页
采用体式显微镜、优化设计软件研究了ENiCrMo3T0-4药芯焊丝中药芯组成及工艺参数对气孔敏感性的影响。结果表明:随着焊丝药芯组成中SiO_2/ZrO_2、TiO_2/ZrO_2、(TiO_2+ZrO_2+SiO_2)/MnO的减小,气孔敏感性降低;气体流量的改变对焊缝表面... 采用体式显微镜、优化设计软件研究了ENiCrMo3T0-4药芯焊丝中药芯组成及工艺参数对气孔敏感性的影响。结果表明:随着焊丝药芯组成中SiO_2/ZrO_2、TiO_2/ZrO_2、(TiO_2+ZrO_2+SiO_2)/MnO的减小,气孔敏感性降低;气体流量的改变对焊缝表面针眼气孔数的影响不大,但气体流量过小会产生条虫状气孔;当焊接电压25 V、焊接电流160 A、干伸长量20 mm时,焊缝金属针眼气孔数最少,焊丝气孔敏感性最低;增大固液相温度区间及氢在高温熔渣中的溶解度,可以降低焊缝金属气孔敏感性。 展开更多
关键词 镍基药芯焊丝 药芯组成 工艺参数 气孔敏感性
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部