This paper investigates the effects of tool holder materials on chatter vibration in turning operations.The study uses a complex dynamic turning model with two degrees of freedom for the orthogonal cutting system.Tool...This paper investigates the effects of tool holder materials on chatter vibration in turning operations.The study uses a complex dynamic turning model with two degrees of freedom for the orthogonal cutting system.Tool holders made from different materials,including Al 5083,Al 6082,Al 7012,and a standard 4140 material,were subjected to chatter vibration to investigate their process damping capabilities.The study found that the standard tool holder 4140 allows for higher stable depths of cut and produces similar process damping values compared to the other tool holders.Finite element analyses(FEA)were performed to verify the experimental results,and the modal and FEA analyses produced very similar results.The study concludes that future research should investigate the effects of tool holders made from high alloy steel alloys on process damping.Overall,this paper provides important insights into the effects of tool hold-er materials on chatter vibration and process damping in turning operations,which can help in the design of more effi-cient and effective cutting systems.展开更多
The drilling process in orthopedic surgery can sometimes lead to an undesired increase in temperature,which can cause serious damage to bones and soft tissues.This overheating is typically identified as a temperature ...The drilling process in orthopedic surgery can sometimes lead to an undesired increase in temperature,which can cause serious damage to bones and soft tissues.This overheating is typically identified as a temperature above 47℃,known as the critical limit,and can result in the condition known as osteonecrosis.This study aims to develop a new control system,using a proportional-integral-derivative(PID)controller,to prevent overheating and the resulting osteonecrosis.The bone temperature is constantly measured using a thermocouple and,when it reaches the critical temperature of 47℃,the cooling device is activated by the PID-controlled system.This new control system makes the drill machine with cooling device more user-friendly and allows surgeons to set a desired temperature level manually.展开更多
In this study,the reason for erosion-corrosion of drinking or mains water in the faucet was investigated by computational fluid dynamics.Pipes used in homes,the service sector,and industry are responsible for transpor...In this study,the reason for erosion-corrosion of drinking or mains water in the faucet was investigated by computational fluid dynamics.Pipes used in homes,the service sector,and industry are responsible for transporting different types of fluids from one place to another.Considering the faucet design,the SolidWorks program was used for 3D studies.In-faucet flow analyses were performed using Ansys Fluent,a computational fluid dynamics program based on the finite volume method.In the analyses,lime particles were chosen.At the end of the analysis,the amount of erosion in the faucet was obtained.展开更多
基金This study was supported by the Scientific Research Coordination Unit of Pamukkale University under the project number 2011BSP020.
文摘This paper investigates the effects of tool holder materials on chatter vibration in turning operations.The study uses a complex dynamic turning model with two degrees of freedom for the orthogonal cutting system.Tool holders made from different materials,including Al 5083,Al 6082,Al 7012,and a standard 4140 material,were subjected to chatter vibration to investigate their process damping capabilities.The study found that the standard tool holder 4140 allows for higher stable depths of cut and produces similar process damping values compared to the other tool holders.Finite element analyses(FEA)were performed to verify the experimental results,and the modal and FEA analyses produced very similar results.The study concludes that future research should investigate the effects of tool holders made from high alloy steel alloys on process damping.Overall,this paper provides important insights into the effects of tool hold-er materials on chatter vibration and process damping in turning operations,which can help in the design of more effi-cient and effective cutting systems.
基金supported by the Department of Scientific Research Project Unit at Kocaeli University under the project number of 2012/44.
文摘The drilling process in orthopedic surgery can sometimes lead to an undesired increase in temperature,which can cause serious damage to bones and soft tissues.This overheating is typically identified as a temperature above 47℃,known as the critical limit,and can result in the condition known as osteonecrosis.This study aims to develop a new control system,using a proportional-integral-derivative(PID)controller,to prevent overheating and the resulting osteonecrosis.The bone temperature is constantly measured using a thermocouple and,when it reaches the critical temperature of 47℃,the cooling device is activated by the PID-controlled system.This new control system makes the drill machine with cooling device more user-friendly and allows surgeons to set a desired temperature level manually.
文摘In this study,the reason for erosion-corrosion of drinking or mains water in the faucet was investigated by computational fluid dynamics.Pipes used in homes,the service sector,and industry are responsible for transporting different types of fluids from one place to another.Considering the faucet design,the SolidWorks program was used for 3D studies.In-faucet flow analyses were performed using Ansys Fluent,a computational fluid dynamics program based on the finite volume method.In the analyses,lime particles were chosen.At the end of the analysis,the amount of erosion in the faucet was obtained.
