In order to deeply study the leaf-stripping principle for corn stalk, the hexagon-enveloping leaf-stripping experimental device was designed. To achieve higher leaf-stripping percent and provide important references f...In order to deeply study the leaf-stripping principle for corn stalk, the hexagon-enveloping leaf-stripping experimental device was designed. To achieve higher leaf-stripping percent and provide important references for the separation equipment for corn stalk, it is necessary to fired out the laws of leaf-stripping of such mechanism and to select the main influencing factors of separation performance from a number of factors. Through the study on hexagon-enveloping leaf-stripping mechanism for corn stalks, the leaf- stripping principle of such mechanism was more clear, and the optimization of structural and kinematic parameters achieved by the experiment whose influencing factors were the four selected ones （feeding speed, rotary speed of leaf-stripping roll, clearance and included angle between two leaf-stripping plates） could be directly applied to the development of efficient rind-pith or leaf-stripping separation for corn stalks.展开更多
Alumina-based composites containing 0-15wt% Ni metallic phase were produced by hot press-sintering Ni-coated alumina powders. The Ni-coated alumina powders were prepared by the aqueous heterogeneous precipitation of a...Alumina-based composites containing 0-15wt% Ni metallic phase were produced by hot press-sintering Ni-coated alumina powders. The Ni-coated alumina powders were prepared by the aqueous heterogeneous precipitation of alumina micro-powders and nickel sulfate salt followed by reduction process. The microstructural features and dispersion of Ni phase in Ni-coated alumina powders and the subsequent alumina-Ni cermets were investigated using scanning electron microscope （SEM）, X-ray diffractometer （XRD）, and transmission electron microscope （TEM）. The relative density of the hot press-sintered composites was measured with the Archimedes＇ method while the fracture strength and the fracture toughness were defined with the three-point bending method and the micro-indentation fracture method. In the formation of alumina-Ni cermets from sintered Ni-coated alumina powders, Ni phase to some extent limits the densification rate and stifles the coarsening and growing process of alumina grains. The Ni phase is found to be located at the interfaces and the triple-joint junctions of alumina grains which results into alteration of the fracture mode of alumina and its increased fracture strength and fracture toughness if compared with monolithic alumina.展开更多
基金Supported by the National Science and Technology Support Funded Project(2011BAD20B08)
文摘In order to deeply study the leaf-stripping principle for corn stalk, the hexagon-enveloping leaf-stripping experimental device was designed. To achieve higher leaf-stripping percent and provide important references for the separation equipment for corn stalk, it is necessary to fired out the laws of leaf-stripping of such mechanism and to select the main influencing factors of separation performance from a number of factors. Through the study on hexagon-enveloping leaf-stripping mechanism for corn stalks, the leaf- stripping principle of such mechanism was more clear, and the optimization of structural and kinematic parameters achieved by the experiment whose influencing factors were the four selected ones （feeding speed, rotary speed of leaf-stripping roll, clearance and included angle between two leaf-stripping plates） could be directly applied to the development of efficient rind-pith or leaf-stripping separation for corn stalks.
基金Innovation Foundation of Jiangsu University(04CX01)
文摘Alumina-based composites containing 0-15wt% Ni metallic phase were produced by hot press-sintering Ni-coated alumina powders. The Ni-coated alumina powders were prepared by the aqueous heterogeneous precipitation of alumina micro-powders and nickel sulfate salt followed by reduction process. The microstructural features and dispersion of Ni phase in Ni-coated alumina powders and the subsequent alumina-Ni cermets were investigated using scanning electron microscope （SEM）, X-ray diffractometer （XRD）, and transmission electron microscope （TEM）. The relative density of the hot press-sintered composites was measured with the Archimedes＇ method while the fracture strength and the fracture toughness were defined with the three-point bending method and the micro-indentation fracture method. In the formation of alumina-Ni cermets from sintered Ni-coated alumina powders, Ni phase to some extent limits the densification rate and stifles the coarsening and growing process of alumina grains. The Ni phase is found to be located at the interfaces and the triple-joint junctions of alumina grains which results into alteration of the fracture mode of alumina and its increased fracture strength and fracture toughness if compared with monolithic alumina.
