The tribological performance of the sliding bearings which are probably made of polymers, which is subjected to magnetic field, is of great intense. The wear of epoxy composites filled by metallic particles such as ir...The tribological performance of the sliding bearings which are probably made of polymers, which is subjected to magnetic field, is of great intense. The wear of epoxy composites filled by metallic particles such as iron, copper and aluminum scratched by steel indenter is investigated. The wear scar width of the scratch was measured by an optical microscope. It was found that wear displayed by the scratch of epoxy filled by the metallic filling materials such as iron, copper and aluminum increased with increasing applied load. As the content of the metallic filling materials increased, wear slightly increased due to the reduction in cohesive stress inside the matrix as well as the epoxy transfer into the indenter surface might be responsible for that behavior. For epoxy filled by iron, when the magnetic field was applied to the contact area wear significantly decreased. Increasing the intensity of the magnetic field showed slight wear increase. Wear displayed by the scratch of epoxy filled by copper showed higher values than that observed for copper filled epoxy. Presence of the magnetic field might generate electric current at the contact area leading to an increase in the intensity of the electric static charge. Moreover, wear of epoxy filled by aluminum showed lower values than that observed for epoxy composites filled by copper and higher than that displayed by iron filled epoxy composites. Under the effect of magnetic field, wear significantly increased. This behavior could explained on the basis that the presence of magnetic field accompanied by the movement of the indenter in the epoxy composites generated electric current passing through the steel indenter which caused softening of the epoxy composites. In that condition removal of epoxy from the wear track was easier and epoxy transfer into the steel indenter was accelerated.展开更多
The wide use of epoxy composites as bearing materials in electronic appliances necessitates studying their frictional behaviour under the influence of magnetic field. Experiments were carried out to investigate the ef...The wide use of epoxy composites as bearing materials in electronic appliances necessitates studying their frictional behaviour under the influence of magnetic field. Experiments were carried out to investigate the effect of magnetic field on the friction coefficient displayed by the scratch of epoxy composites filled by iron, copper and aluminium particles at different concentrations. It was observed that, for epoxy filled by the metallic fillers (iron, copper and aluminium), under the effect of the magnetic field, friction coefficient showed relative decrease then significantly increased with further increase of the intensity of the magnetic field. Besides, friction coefficient increased with increasing the content of the metallic fillers due to the decrease of the strength of the epoxy matrix. The values of friction coefficient displayed by epoxy filled by copper were lower than those observed for epoxy filled by iron. Filling epoxy by aluminium displayed lower friction coefficient than that observed for epoxy composites filled by iron and copper. This can be attributed to the charging of aluminium by positive charge when slid against steel. The resultant charge on the sliding surfaces was lower than that generated when epoxy was filled by iron and copper. In that condition, the adhesion of epoxy composites would be relatively weaker leading to the decrease of friction coefficient.展开更多
文摘The tribological performance of the sliding bearings which are probably made of polymers, which is subjected to magnetic field, is of great intense. The wear of epoxy composites filled by metallic particles such as iron, copper and aluminum scratched by steel indenter is investigated. The wear scar width of the scratch was measured by an optical microscope. It was found that wear displayed by the scratch of epoxy filled by the metallic filling materials such as iron, copper and aluminum increased with increasing applied load. As the content of the metallic filling materials increased, wear slightly increased due to the reduction in cohesive stress inside the matrix as well as the epoxy transfer into the indenter surface might be responsible for that behavior. For epoxy filled by iron, when the magnetic field was applied to the contact area wear significantly decreased. Increasing the intensity of the magnetic field showed slight wear increase. Wear displayed by the scratch of epoxy filled by copper showed higher values than that observed for copper filled epoxy. Presence of the magnetic field might generate electric current at the contact area leading to an increase in the intensity of the electric static charge. Moreover, wear of epoxy filled by aluminum showed lower values than that observed for epoxy composites filled by copper and higher than that displayed by iron filled epoxy composites. Under the effect of magnetic field, wear significantly increased. This behavior could explained on the basis that the presence of magnetic field accompanied by the movement of the indenter in the epoxy composites generated electric current passing through the steel indenter which caused softening of the epoxy composites. In that condition removal of epoxy from the wear track was easier and epoxy transfer into the steel indenter was accelerated.
文摘The wide use of epoxy composites as bearing materials in electronic appliances necessitates studying their frictional behaviour under the influence of magnetic field. Experiments were carried out to investigate the effect of magnetic field on the friction coefficient displayed by the scratch of epoxy composites filled by iron, copper and aluminium particles at different concentrations. It was observed that, for epoxy filled by the metallic fillers (iron, copper and aluminium), under the effect of the magnetic field, friction coefficient showed relative decrease then significantly increased with further increase of the intensity of the magnetic field. Besides, friction coefficient increased with increasing the content of the metallic fillers due to the decrease of the strength of the epoxy matrix. The values of friction coefficient displayed by epoxy filled by copper were lower than those observed for epoxy filled by iron. Filling epoxy by aluminium displayed lower friction coefficient than that observed for epoxy composites filled by iron and copper. This can be attributed to the charging of aluminium by positive charge when slid against steel. The resultant charge on the sliding surfaces was lower than that generated when epoxy was filled by iron and copper. In that condition, the adhesion of epoxy composites would be relatively weaker leading to the decrease of friction coefficient.
