Biodiesel has generated increased interest recently as an alternative to petroleum-derived diesel. Due to its high oxygen content, biodiesel typically burns more completely than petroleum diesel, and thus has lower em...Biodiesel has generated increased interest recently as an alternative to petroleum-derived diesel. Due to its high oxygen content, biodiesel typically burns more completely than petroleum diesel, and thus has lower emissions of hydrocarbons (HC), carbon monoxide (CO), and particulate matter (PM). However, biodiesel may increase or decrease nitrogen oxide (NOx) and carbon dioxide (CO2) emissions, depending on biodiesel feedstock, engine type, and test cycle. The purpose of this study was to compare emissions from 20% blends of biodiesel made from 4 feedstocks (soybean oil, canola oil, waste cooking oil, and animal fat) with emissions from ultra low sulfur diesel (ULSD). Emissions of NOx and CO2 were made under real-world driving conditions using a Horiba On-Board Measurement System OBS-1300 on a highway route and arterial route;emissions of NOx, CO2, HC, CO, and PM were measured in a controlled setting using a chassis dynamometer with Urban Dynamometer Drive Schedule. Dynamometer test results showed statistically significant lower emissions of HC, CO, and PM from all B20 blends compared to ULSD. For CO2, both on-road testing (arterial, highway, and idling) and dynamometer testing showed no statistically significant difference in emissions among the B20 blends and ULSD. For NOx, dynamometer testing showed only B20 from soybean oil to have statistically significant higher emissions. This is generally consistent with the on-road testing, which showed no statistically significant difference in NOx emissions between ULSD and the B20 blends.展开更多
The objective of this research was development of a statistical model for estimating vehicle tailpipe emissions of carbon dioxide (CO2). Forty hours of second-by-second emissions data (144,000 data points) were collec...The objective of this research was development of a statistical model for estimating vehicle tailpipe emissions of carbon dioxide (CO2). Forty hours of second-by-second emissions data (144,000 data points) were collected using an On-Board emissions measurement System (Horiba OBS-1300) installed in a 2007 Dodge Charger car. Data were collected for two roadway types, arterial and highway, around Arlington, Texas, and two different time periods, off peak and peak (both a.m. and p.m.). Multiple linear regression and SAS software were used to build emission models from the data, using predictor variables of velocity, acceleration and an interaction term. The arterial model explained 61% of the variability in the emissions;the highway model explained 27%. The arterial model in particular represents a reasonably good compromise between accuracy and ease of use. The arterial model could be coupled with velocity and acceleration profiles obtained from a micro-scale traffic simulation model, such as CORSIM, or from field data from an instrumented vehicle, to estimate percent emission reductions associated with local changes in traffic system operation or management.展开更多
文摘Biodiesel has generated increased interest recently as an alternative to petroleum-derived diesel. Due to its high oxygen content, biodiesel typically burns more completely than petroleum diesel, and thus has lower emissions of hydrocarbons (HC), carbon monoxide (CO), and particulate matter (PM). However, biodiesel may increase or decrease nitrogen oxide (NOx) and carbon dioxide (CO2) emissions, depending on biodiesel feedstock, engine type, and test cycle. The purpose of this study was to compare emissions from 20% blends of biodiesel made from 4 feedstocks (soybean oil, canola oil, waste cooking oil, and animal fat) with emissions from ultra low sulfur diesel (ULSD). Emissions of NOx and CO2 were made under real-world driving conditions using a Horiba On-Board Measurement System OBS-1300 on a highway route and arterial route;emissions of NOx, CO2, HC, CO, and PM were measured in a controlled setting using a chassis dynamometer with Urban Dynamometer Drive Schedule. Dynamometer test results showed statistically significant lower emissions of HC, CO, and PM from all B20 blends compared to ULSD. For CO2, both on-road testing (arterial, highway, and idling) and dynamometer testing showed no statistically significant difference in emissions among the B20 blends and ULSD. For NOx, dynamometer testing showed only B20 from soybean oil to have statistically significant higher emissions. This is generally consistent with the on-road testing, which showed no statistically significant difference in NOx emissions between ULSD and the B20 blends.
文摘The objective of this research was development of a statistical model for estimating vehicle tailpipe emissions of carbon dioxide (CO2). Forty hours of second-by-second emissions data (144,000 data points) were collected using an On-Board emissions measurement System (Horiba OBS-1300) installed in a 2007 Dodge Charger car. Data were collected for two roadway types, arterial and highway, around Arlington, Texas, and two different time periods, off peak and peak (both a.m. and p.m.). Multiple linear regression and SAS software were used to build emission models from the data, using predictor variables of velocity, acceleration and an interaction term. The arterial model explained 61% of the variability in the emissions;the highway model explained 27%. The arterial model in particular represents a reasonably good compromise between accuracy and ease of use. The arterial model could be coupled with velocity and acceleration profiles obtained from a micro-scale traffic simulation model, such as CORSIM, or from field data from an instrumented vehicle, to estimate percent emission reductions associated with local changes in traffic system operation or management.
