Both a conventional flow distributer and an improved one with a flow buffer were applied respectively during the high pressure die casting(HPDC)process,and samples of AZ91D magnesium alloy with different microstructur...Both a conventional flow distributer and an improved one with a flow buffer were applied respectively during the high pressure die casting(HPDC)process,and samples of AZ91D magnesium alloy with different microstructure mainly consisting ofα-Mg grains,β-phase and porosities were obtained.According to the grain orientation analysis,the predominant deformation behavior inα-Mg grains was dislocation slip,supplemented by deformation twinning.Dislocation slip was more difficult to occur in the samples with the improved flow distributer on account of the fact that the size ofα-Mg grains in the microstructure was finer and more uniform.During the in situ tensile deformation test,cracks were observed to initiate from gas-shrinkage pore and island-shrinkage,and two main crack propagation mechanisms,porosity growth and coalescence were found accordingly.When the crack was in contact with theβ-phase,it would pass through and fracture the networkβ-phase,whereas bypass the islandβ-phase by detaching it from the surroundingα-Mg grains.Mechanical property tests showed that the samples with relatively more homogeneous microstructure would perform higher mechanical properties,which was the combined effect of matrixα-Mg grains,β-phase,and porosities.展开更多
A numerical model based on the cellular automaton method for the three-dimensional simulation of dendritic growth of magnesium alloy was developed. The growth ki- netics was calculated from the complete solution of th...A numerical model based on the cellular automaton method for the three-dimensional simulation of dendritic growth of magnesium alloy was developed. The growth ki- netics was calculated from the complete solution of the transport equations. By con- structing a three-dimensional anisotropy model with the cubic CA cells, simulation of dendritic growth of magnesium alloy with six-fold symmetry in the basal plane was achieved. The model was applied to simulate the equiaxed dendritic growth and columnar dendritic growth under directional solidification, and its capability was addressed by comparing the simulated results to experimental results and those in the previously published works. Meanwhile, the three-dimensional simulated results were also compared with that of in two dimensions, offering a deep insight into the microstructure formation of magnesium alloy during solidification.展开更多
基金financially the National Natural Science Foundation of China(No.51805389)Natural Science Foundation of Hubei Province of China(No.2018CFB210)111 Project(B17034)。
文摘Both a conventional flow distributer and an improved one with a flow buffer were applied respectively during the high pressure die casting(HPDC)process,and samples of AZ91D magnesium alloy with different microstructure mainly consisting ofα-Mg grains,β-phase and porosities were obtained.According to the grain orientation analysis,the predominant deformation behavior inα-Mg grains was dislocation slip,supplemented by deformation twinning.Dislocation slip was more difficult to occur in the samples with the improved flow distributer on account of the fact that the size ofα-Mg grains in the microstructure was finer and more uniform.During the in situ tensile deformation test,cracks were observed to initiate from gas-shrinkage pore and island-shrinkage,and two main crack propagation mechanisms,porosity growth and coalescence were found accordingly.When the crack was in contact with theβ-phase,it would pass through and fracture the networkβ-phase,whereas bypass the islandβ-phase by detaching it from the surroundingα-Mg grains.Mechanical property tests showed that the samples with relatively more homogeneous microstructure would perform higher mechanical properties,which was the combined effect of matrixα-Mg grains,β-phase,and porosities.
基金supported by the Ministry of Science and Technology of China(Nos.2011BAE21B00,2011ZX04001-071 and 2010DFA72760)
文摘A numerical model based on the cellular automaton method for the three-dimensional simulation of dendritic growth of magnesium alloy was developed. The growth ki- netics was calculated from the complete solution of the transport equations. By con- structing a three-dimensional anisotropy model with the cubic CA cells, simulation of dendritic growth of magnesium alloy with six-fold symmetry in the basal plane was achieved. The model was applied to simulate the equiaxed dendritic growth and columnar dendritic growth under directional solidification, and its capability was addressed by comparing the simulated results to experimental results and those in the previously published works. Meanwhile, the three-dimensional simulated results were also compared with that of in two dimensions, offering a deep insight into the microstructure formation of magnesium alloy during solidification.
