Development of Preliminary Design Program for Combustor of Regenerative Cooled Liquid Rocket Engine

An integrated program was established to design a combustor for a liquid rocket engine and to analyze regenerative cooling results on a preliminary design level.Properties of burnt gas from a kerosene-LOx mixture in the combustor and rocket performance were calculated from CEA which is the code for the calculation of chemical equilibrium.The heat transfer of regenerative cooling was analyzed by using SUPERTRAPP code for coolant properties and by one-dimensional correlations of the heat transfer coefficient from the combustor liner to the coolant.Profiles of the combustors of F-1 and RS-27A engines were designed from similar input data and the present results were compared to actual data for validation.Finally,the combustors of 30 tonf class,75 tonf class and 150 tonf class were designed from the required thrust,combustion chamber,exit pressure and mixture ratio of propellants.The wall temperature,heat flux and pressure drop were calculated for heat transfer analysis of regenerative cooling using the profiles.

Effects of Momentum Ratio and Weber Number on Spray Half Angles of Liquid Controlled Pintle Injector

一个舵栓注射者为扼杀一台液体火箭引擎并且减少引擎重量是有益的。这研究为液体气体燃料在舵栓注射者的水花特征上以各种各样的注射条件探索动量比率和威伯数字的效果。一张液体表从一张中心舵栓嘴被注射，它被一口煤气的喷气从环形的差距打破。燃料的压力落下，和舵栓洞距离被看作控制变量；使用 0.1 1.0 液体注射作为为压力的一个酒吧落下，为为舵栓洞距离的煤气的喷气和 0.2 1.0 公里的压力落下的 0.010.2 酒吧。分泌物系数在 0.75 公里的舵栓洞距离前线性地被减少然后，系数稍微被增加。水花图象被一个互补金属氧化物半导体照相机与高分辨率捕获。然后，阴影和反映的图象被分析。水花分布被 patternator 从一个舵栓尖端与 50 公里的轴的距离测量。最后，角度有指数地减少的水花一半动量比率由威伯数字划分了的关联。另外，水花一半从水花分发的角度与从捕获的图象测量的那些相比被低估。

Verification on Spray Simulation of a Pintle Injector for Liquid Rocket Engine

The pintle injector used for a liquid rocket engine is a newly re-attracted injection system famous for its wide throttle ability with high efficiency. The pintle injector has many variations with complex inner structures due to its moving parts. In order to study the rotating flow near the injector tip, which was observed from the cold flow experiment using water and air, a numerical simulation was adopted and a verification of the numerical model was later conducted. For the verification process, three types of experimental data including velocity distributions of gas flows, spray angles and liquid distribution were all compared using simulated results. The numerical simulation was performed using a commercial simulation program with the Eulerian multiphase model and axisymmetric two dimensional grids. The maximum and minimum velocities of gas were within the acceptable range of agreement, however, the spray angles experienced up to 25% error when the momentum ratios were increased. The spray density distributions were quantitatively measured and had good agreement. As a result of this study, it was concluded that the simulation method was properly constructed to study specific flow characteristics of the pintle injector despite having the limitations of two dimensional and coarse grids.

Genetic Algorithm to Optimize the Design of Main Combustor and Gas Generator in Liquid Rocket Engines

A genetic algorithm was used to develop optimal design methods for the regenerative cooled combustor and fuel-rich gas generator of a liquid rocket engine. For the combustor design, a chemical equilibrium analysis was applied, and the profile was calculated using Rao's method. One-dimensional heat transfer was assumed along the profile, and cooling channels were designed. For the gas-generator design, non-equilibrium properties were derived from a counterflow analysis, and a vaporization model for the fuel droplet was adopted to calculate residence time. Finally, a genetic algorithm was adopted to optimize the designs. The combustor and gas generator were optimally designed for 30-tonf, 75-tonf, and 150-tonf engines. The optimized combustors demonstrated superior design characteristics when compared with previous non-optimized results. Wall temperatures at the nozzle throat were optimized to satisfy the requirement of 800 K, and specific impulses were maximized. In addition, the target turbine power and a burned-gas temperature of 1000 K were obtained from the optimized gas-generator design.

Conceptual Design for a Kerosene Fuel-rich Gas-generator of a Turbopump-fed Liquid Rocket Engine

A design method for a kerosene fuel-rich gas-generator of a liquid rocket engine using turbopumps to supply propellant was performed at a conceptual level. The gas-generator creates hot gases, enabling the turbine to operate the turbopumps. A chemical non-equilibrium analysis and a droplet vaporization model were used for the estimation of the burnt gas properties and characteristic chamber length. A premixed counter-flow flame analysis was performed for the prediction of the burnt gas properties, namely the temperature, the specific heat ratio and heat capacity, and the chemical reaction time. To predict the vaporization time, the Spalding model, using a single droplet in convective condition, was used. The minimum residence time in the chamber and the characteristic length were calculated by adding the reaction time and the vaporization time. Using the characteristic length, the design methods for the fuel-rich gas-generator were established. Finally, a parametric study was achieved for the effects of the O/F ratio, mass flow rate, chamber pressure, initial droplet temperature, initial droplet diameter and initial droplet velocity.

Effects of Supercritical Environment on Hydrocarbon-fuel Injection

In this study, the effects of environment conditions on decane were investigated. Decane was injected in subcritical and supercritical ambient conditions. The visualization chamber was pressurized to 1.68 MPa by using nitrogen gas at a temperature of 653 K for subcritical ambient conditions. For supercritical ambient conditions, the visualization chamber was pressurized to 2.52 MPa by using helium at a temperature of 653 K. The decane injection in the pressurized chamber was visualized via a shadowgraph technique and gradient images were obtained by a post processing method. A large variation in density gradient was observed at jet interface in the case of subcritical injection in subcritical ambient conditions. Conversely, for supercritical injection in supercritical ambient conditions, a small density gradient was observed at the jet interface. In a manner similar to that observed in other cases, supercritical injection in subcritical ambient conditions differed from supercritical ambient conditions such as sphere shape liquid. Additionally, there were changes in the interface, and the supercritical injection core width was thicker than that in the subcritical injection. Furthermore, in cases with the same injection conditions, the change in the supercritical ambient normalized core width was smaller than the change in the subcritical ambient normalized core width owing to high specific heat at the supercritical injection and small phase change at the interface. Therefore, the interface was affected by the changing ambient condition. Given that the effect of changing the thermodynamic properties of propellants could be essential for a variable thrust rocket engine, the effects of the ambient conditions were investigated experimentally.