The transient liquid phase(TLP)bonding of CoCuFeMnNi high entropy alloy(HEA)was studied.The TLP bonding was performed using AWS BNi-2 interlayer at 1050℃ with the TLP bonding time of 20,60,180 and 240 min.The effect ...The transient liquid phase(TLP)bonding of CoCuFeMnNi high entropy alloy(HEA)was studied.The TLP bonding was performed using AWS BNi-2 interlayer at 1050℃ with the TLP bonding time of 20,60,180 and 240 min.The effect of bonding time on the joint microstructure was characterized by SEM and EDS.Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time.For samples bonded at 20,60 and 180 min,athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn3Si intermetallic compound.For all samples,theγsolid solution was formed in the isothermal solidification zone of the bonding zone.To evaluate the effect of TLP bonding time on mechanical properties of joints,the shear strength and micro-hardness of joints were measured.The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints.The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min,respectively.展开更多
In the present study, (Fe,Cr)3Al/20 vol% A1203 nanocomposite was prepared through mechanochemical reactions during ball milling and successfully bulked using a combination of cold isostatic press and sintering at 1...In the present study, (Fe,Cr)3Al/20 vol% A1203 nanocomposite was prepared through mechanochemical reactions during ball milling and successfully bulked using a combination of cold isostatic press and sintering at 1400℃ for 1 h. Two processing approaches were utilized to produce (Fe,Cr)3A1/A1203 nanocomposite: The first was milling of Fe, Cr, AI and Fe203, while the second one was milling of Fe, Cr, Al and Cr203, both in stoichiometric condition, to synthesize (Fe,Cr)3Al/20 vol% Al2O3. Structural changes of powder particles during mechanical alloying were studied by X-ray diffraction. The microstructure and the morphology of powder particles and bulk samples were also studied by scanning electron microscopy and transmission electron microscopy. Microstructural analysis showed that mechanochemical reactions took place during milling, and nanometric Al2O3 was uniformly distributed in the matrix. The results also showed that the second approach required a considerably higher milling time to produce (Fe,Cr)3Al/Al2O3 nanocomposite, as compared to the first one. For this reason, bulk samples were produced from the synthesized nanocomposite in the first approach. The microstructure of the sintered samples consisted of a network structure of (Fe,Cr)3Al and Al2O3 phases with superior mechanical properties.展开更多
In this study, microstructural evolution of Mg–Ni alloy during mechanical alloying(MA) was investigated.Also, a thermodynamic approach was utilized to predict the most stable phases formed in Mg–Ni alloy after MA....In this study, microstructural evolution of Mg–Ni alloy during mechanical alloying(MA) was investigated.Also, a thermodynamic approach was utilized to predict the most stable phases formed in Mg–Ni alloy after MA. The phase composition and microstructural properties of Mg–Ni alloy were assessed by X-ray diffractometry, high-resolution field emission scanning electron microscopy and high-resolution transmission electron microscopy. The results showed that ball milling of magnesium and nickel powder mixture for 70 h yields nanostructural Mg2Ni compound with an average grain size of ~20 nm. Thermodynamic calculations revealed that in the composition ranges of 0.0 / XMg/ 0.03(at.%)and 0.97 / XMg/ 1, there is no driving force for amorphous phase formation. In the composition range of 0.07 / XMg/ 0.93, the change of Gibbs free energy for amorphous phase formation was more negative than solid solution.While for XMg= 0.66(nominal composition of Mg2Ni intermetallic phase), the change of Gibbs free energy for intermetallic phase was found to be more negative than both amorphous and solid solution phases indicating that Mg2Ni intermetallic compound is the most stable phase, in agreement with the experimental observations.展开更多
文摘The transient liquid phase(TLP)bonding of CoCuFeMnNi high entropy alloy(HEA)was studied.The TLP bonding was performed using AWS BNi-2 interlayer at 1050℃ with the TLP bonding time of 20,60,180 and 240 min.The effect of bonding time on the joint microstructure was characterized by SEM and EDS.Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time.For samples bonded at 20,60 and 180 min,athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn3Si intermetallic compound.For all samples,theγsolid solution was formed in the isothermal solidification zone of the bonding zone.To evaluate the effect of TLP bonding time on mechanical properties of joints,the shear strength and micro-hardness of joints were measured.The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints.The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min,respectively.
文摘In the present study, (Fe,Cr)3Al/20 vol% A1203 nanocomposite was prepared through mechanochemical reactions during ball milling and successfully bulked using a combination of cold isostatic press and sintering at 1400℃ for 1 h. Two processing approaches were utilized to produce (Fe,Cr)3A1/A1203 nanocomposite: The first was milling of Fe, Cr, AI and Fe203, while the second one was milling of Fe, Cr, Al and Cr203, both in stoichiometric condition, to synthesize (Fe,Cr)3Al/20 vol% Al2O3. Structural changes of powder particles during mechanical alloying were studied by X-ray diffraction. The microstructure and the morphology of powder particles and bulk samples were also studied by scanning electron microscopy and transmission electron microscopy. Microstructural analysis showed that mechanochemical reactions took place during milling, and nanometric Al2O3 was uniformly distributed in the matrix. The results also showed that the second approach required a considerably higher milling time to produce (Fe,Cr)3Al/Al2O3 nanocomposite, as compared to the first one. For this reason, bulk samples were produced from the synthesized nanocomposite in the first approach. The microstructure of the sintered samples consisted of a network structure of (Fe,Cr)3Al and Al2O3 phases with superior mechanical properties.
基金the Iran National Science Foundation (INSF) under Grant No. 85054/35
文摘In this study, microstructural evolution of Mg–Ni alloy during mechanical alloying(MA) was investigated.Also, a thermodynamic approach was utilized to predict the most stable phases formed in Mg–Ni alloy after MA. The phase composition and microstructural properties of Mg–Ni alloy were assessed by X-ray diffractometry, high-resolution field emission scanning electron microscopy and high-resolution transmission electron microscopy. The results showed that ball milling of magnesium and nickel powder mixture for 70 h yields nanostructural Mg2Ni compound with an average grain size of ~20 nm. Thermodynamic calculations revealed that in the composition ranges of 0.0 / XMg/ 0.03(at.%)and 0.97 / XMg/ 1, there is no driving force for amorphous phase formation. In the composition range of 0.07 / XMg/ 0.93, the change of Gibbs free energy for amorphous phase formation was more negative than solid solution.While for XMg= 0.66(nominal composition of Mg2Ni intermetallic phase), the change of Gibbs free energy for intermetallic phase was found to be more negative than both amorphous and solid solution phases indicating that Mg2Ni intermetallic compound is the most stable phase, in agreement with the experimental observations.