Substitution of Aggregates in Concrete and Mortar with Coltan Mining Waste: Mechanical, Environmental, and Economic Impact Case Study

The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.

Study of Sands from Bamendou-West Cameroon: Valorization for Concrete Mix Design

Bamendou (West Cameroon), has a huge potential in natural resources, especially sands. However, the use of these materials in civil engineering works leads to the appearance of numerous pathologies which in some cases lead to the total ruin of the works. In order to overcome these infrastructural problems, the main objective of this study is set at the improvement of the service life of structures built in Cameroon using local materials formed under climatic, geological and geotechnical conditions similar to those of materials in Bamendou. Eight sand samples were taken from the most representative and exploited quarries. The identification and classification of the sand taken from the most representative quarries in the study area show that they are mainly clayey, with an average sand equivalent of 57.54. In terms of granulometry, the curves of several sand samples do not fall within the granular range of sands used in the formulation of concrete. The modulus of fineness obtained by particle size analysis varies from 2.91 to 3.92 with an average of 3.31.

River Sand Characterization for Its Use in Concrete: A Revue

Despite the gradual professionalization of the construction sector as well as the abundance of sand mining sites offered by the North Kivu, Democratic Republic of Congo Region, ignorance of materials by local builders persists. This is the case of quarries extracting river sand used to make concrete and mortar. However, the dosages of the various constituents are most often chosen on the basis of experience without any prior characterization of this material. This paper presents a comprehensive review of the characterization of river sand for its use in concrete in DRC. The origin and global use of river sand in construction are presented in percentage terms to highlight the importance of river sand as a construction material. The physical properties of river sand, including particle size distribution, bulk density, absolute density, and cleanliness are discussed in detail. The paper examines the effect of variations in river sand properties on concrete behavior, including density and compressive strength. Overall, this paper emphasizes the need to properly characterize river sand before using it in construction to ensure durable, high-quality structures. This will avoid the problems that are observed in particular a bad behavior of the coating on the walls;cracks and crumbling of the beams, lintels, posts and even the ruin of the structures.

Recovery of Mining Wastes in Building Materials: A Review

The use of materials from waste in buildings compensates for the lack of natural resources, solves the problem of waste management and provides an alternative technique for protection of the environment. There are a large number of industrial wastes that are used for full or partial replacement of raw materials in some construction materials. This review assesses mining waste in concrete as a substitute for aggregates and cement;in fired bricks as a substitute for soil;and in road backfill as a substitute for soil. This paper reviews some mining tailings, mine waste rocks and some slags obtained in the exploitation and/or processing of some ores including iron, gold, lead, phosphate, copper, coal, etc. Different physical properties, mechanical properties, chemical properties, heavy metal content, mineralogic composition, geotechnical properties and environmental properties (leaching test) of the mine wastes were examined. The physical, mechanical and environmental properties of the materials obtained by substitution of raw materials by mine waste were examined and compared to reference materials. Mining waste in cementitious materials offers good compressive strengths, while the porosity of the concrete and/or mortar is a factor influencing its toxicity. As for the waste in fired bricks, fired at a temperature of 900°C or more, it offers convincing compressive and flexural strengths. The few research studies obtained on the use of mining waste in road embankments have shown that mining waste can be used as a sub-base layer and backfill as long as it is not toxic. In addition, several other mining wastes require special attention as substitutes for raw materials in construction materials, such as coltan, cobalt.