The microstructures and mechanical properties of 550 MPa grade lightweight high strength thin-walled H-beam steel were experimentally studied. The experimental results show that the microstructure of the air-cooled H-...The microstructures and mechanical properties of 550 MPa grade lightweight high strength thin-walled H-beam steel were experimentally studied. The experimental results show that the microstructure of the air-cooled H-beam steel sample is consisted of ferrite, pearlite and a small amount of granular bainites as well as fine and dispersive V（C,N） precipitates. The microstructure of the water-cooled steel sample is consisted of ferrite and bainite as well as a small amount of fine pearlites. The microstructure of the water-cooled sample is finer than that of the air-cooled sample with the average intercept size of the surface grains reaching to 3.5 gna. The finish rolling temperature of the thin-walled high strength H-beam steel is in the range of 750 ~C-850 ~C. The lower the finish rolling temperature and the faster the cooling rate, the finer the ferrite grains, the volume fraction of bainite is increased through water cooling process. Grain refinement strengthening and precipitation strengthening are used as major strengthening means to develop 550 MPa grade lightweight high strength thin- walled H-beam steel. Vanadium partially soluted in the matrix and contributes to the solution strengthening. The 550 MPa grade high-strength thin-walled H-beam steel could be developed by direct air cooling after hot rolling to fully meet the requirements of the target properties.展开更多
High-temperature tensile tests were conducted for high corrosion resistant weathering steel S450EW.The morphologies of fracture microstructures,dislocations and precipitates were investigated by field emission scannin...High-temperature tensile tests were conducted for high corrosion resistant weathering steel S450EW.The morphologies of fracture microstructures,dislocations and precipitates were investigated by field emission scanning electron microscopy and transmission electron microscopy.The high-temperature plastic deformation behavior and brittle mechanism of S450EW steel were also studied.The experimental results show that the ductility troughs appear at 700-850℃ and 650-900℃ when the strain rates are 3×10^(-3)and 1.5×10^(-2)s^(-1),respectively.With the increase of strain rates,the ductility trough moves to the lower temperature side.The hot ductility is best when the cooling rate is 5℃/s before deformation at 750℃and the area reduction rate reaches 60.56%.Fine second phase particles and inclusions precipitated before and during deformation provide effective core positions for microcracks or microvoids formation during deformation process.It is also easy to cause stress concentration which results in microcracks or microvoids between grains during deformation and ultimately causes damage along the grain boundaries.The precipitated particles inhibit austenite dynamic recrystallization and therefore enhance intergranular fracture along austenite grain boundaries.The deformation induced proeutectoid ferrite films distribute along the austenite grain boundaries hinder the dynamic recrystallization.The deformation concentrated on network ferrite films produces damage of grain boundaries.展开更多
基金Funded by the "11th Five" National Science and Technology Support Project(No.2006BAE03A13)
文摘The microstructures and mechanical properties of 550 MPa grade lightweight high strength thin-walled H-beam steel were experimentally studied. The experimental results show that the microstructure of the air-cooled H-beam steel sample is consisted of ferrite, pearlite and a small amount of granular bainites as well as fine and dispersive V（C,N） precipitates. The microstructure of the water-cooled steel sample is consisted of ferrite and bainite as well as a small amount of fine pearlites. The microstructure of the water-cooled sample is finer than that of the air-cooled sample with the average intercept size of the surface grains reaching to 3.5 gna. The finish rolling temperature of the thin-walled high strength H-beam steel is in the range of 750 ~C-850 ~C. The lower the finish rolling temperature and the faster the cooling rate, the finer the ferrite grains, the volume fraction of bainite is increased through water cooling process. Grain refinement strengthening and precipitation strengthening are used as major strengthening means to develop 550 MPa grade lightweight high strength thin- walled H-beam steel. Vanadium partially soluted in the matrix and contributes to the solution strengthening. The 550 MPa grade high-strength thin-walled H-beam steel could be developed by direct air cooling after hot rolling to fully meet the requirements of the target properties.
基金Funded by the National Natural Science Foundation of China(No.51774006)。
文摘High-temperature tensile tests were conducted for high corrosion resistant weathering steel S450EW.The morphologies of fracture microstructures,dislocations and precipitates were investigated by field emission scanning electron microscopy and transmission electron microscopy.The high-temperature plastic deformation behavior and brittle mechanism of S450EW steel were also studied.The experimental results show that the ductility troughs appear at 700-850℃ and 650-900℃ when the strain rates are 3×10^(-3)and 1.5×10^(-2)s^(-1),respectively.With the increase of strain rates,the ductility trough moves to the lower temperature side.The hot ductility is best when the cooling rate is 5℃/s before deformation at 750℃and the area reduction rate reaches 60.56%.Fine second phase particles and inclusions precipitated before and during deformation provide effective core positions for microcracks or microvoids formation during deformation process.It is also easy to cause stress concentration which results in microcracks or microvoids between grains during deformation and ultimately causes damage along the grain boundaries.The precipitated particles inhibit austenite dynamic recrystallization and therefore enhance intergranular fracture along austenite grain boundaries.The deformation induced proeutectoid ferrite films distribute along the austenite grain boundaries hinder the dynamic recrystallization.The deformation concentrated on network ferrite films produces damage of grain boundaries.
