The aim of this study was to produce bulk nanocrystalline Al/Al12（Fe,V）3Si alloys by mechanical alloying （MA） and subsequent hot pressing （HP） of elemental powders. A nanostructured Al-based solid solution was f...The aim of this study was to produce bulk nanocrystalline Al/Al12（Fe,V）3Si alloys by mechanical alloying （MA） and subsequent hot pressing （HP） of elemental powders. A nanostructured Al-based solid solution was formed by MA of elemental powders for 60 h. After HP of the as-milled powders at 550℃ for 20 min, the Al12（Fe,V）3Si phase was precipitated in a nanocrystalline Al matrix. Scanning electron microscopy （SEM） images of the bulk samples represented a homogeneous and uniform microstructure that was superior to those previously obtained by rapid solidification-powder metallurgy （RS-PM）. Nanostructured Al-8.5Fe-1.3V-1.7Si and Al-11.6Fe-1.3V-2.3Si alloys ex-hibited high HV hardness values of～205 and～254, respectively, which are significantly higher than those reported for the RS-PM counter-parts.展开更多
The void formation and plastic deformation micromechanisms of a cold-rolled DP600 steel during tensile loading were studied by scanning electron microscopy(SEM) and electron backscatter diffraction(EBSD).The SEM obser...The void formation and plastic deformation micromechanisms of a cold-rolled DP600 steel during tensile loading were studied by scanning electron microscopy(SEM) and electron backscatter diffraction(EBSD).The SEM observations revealed that the main void nucleation mechanism in the DP600 steel is decohesion at the ferrite-martensite interfaces.The voids were mostly observed between the closely spaced martensite islands situated at the boundaries of relatively finer ferrite grains.The EBSD results indicated a strain gradient developed from the ferrite-martensite and ferrite-ferrite interfaces into the interior of ferrite grains during the tensile deformation,which led to a stress concentration at these interfaces.Moreover,it was demonstrated that local misorientation inside the finer ferrite grains surrounded by martensite islands was higher than that for the coarser ferrite grains,which made the former more prone to void initiation.展开更多
Tribological behavior of nanostructured pure Al and Al–Al12（Fe,V）3Si alloys containing 27（FVS0812） and 37（FVS1212） vol% of Al12（Fe,V）3Si precipitates was investigated. All samples were prepared using mechanic...Tribological behavior of nanostructured pure Al and Al–Al12（Fe,V）3Si alloys containing 27（FVS0812） and 37（FVS1212） vol% of Al12（Fe,V）3Si precipitates was investigated. All samples were prepared using mechanical alloying followed by hot pressing. Wear tests were performed at room temperature using a pin-on-disk machine. Results showed that the presence of Al12（Fe,V）3Si precipitates increases the wear resistance of nanostructured Al, and the wear resistance increases with increasing the Al12（Fe,V）3Si content. Scanning electron microscopy images of worn surfaces and wear debris demonstrated that abrasion and adhesion are the governing wear mechanisms for the nanostructured FVS0812 alloy at 2 and 5 N normal loads, whereas for the nanostructured FVS1212 alloy, the dominant wear mechanism is abrasion at these loads. A mechanically mixed layer（MML） containing Fe and O was formed on the worn surfaces of FVS0812 and FVS1212 samples at 10 N normal load. Formation and delamination of MML controls the wear behavior of these samples at the normal load of 10 N. It is also found that the presence of Al12（Fe,V）3Si precipitates decreases the friction coefficient of nanostructured Al.展开更多
文摘The aim of this study was to produce bulk nanocrystalline Al/Al12（Fe,V）3Si alloys by mechanical alloying （MA） and subsequent hot pressing （HP） of elemental powders. A nanostructured Al-based solid solution was formed by MA of elemental powders for 60 h. After HP of the as-milled powders at 550℃ for 20 min, the Al12（Fe,V）3Si phase was precipitated in a nanocrystalline Al matrix. Scanning electron microscopy （SEM） images of the bulk samples represented a homogeneous and uniform microstructure that was superior to those previously obtained by rapid solidification-powder metallurgy （RS-PM）. Nanostructured Al-8.5Fe-1.3V-1.7Si and Al-11.6Fe-1.3V-2.3Si alloys ex-hibited high HV hardness values of～205 and～254, respectively, which are significantly higher than those reported for the RS-PM counter-parts.
文摘The void formation and plastic deformation micromechanisms of a cold-rolled DP600 steel during tensile loading were studied by scanning electron microscopy(SEM) and electron backscatter diffraction(EBSD).The SEM observations revealed that the main void nucleation mechanism in the DP600 steel is decohesion at the ferrite-martensite interfaces.The voids were mostly observed between the closely spaced martensite islands situated at the boundaries of relatively finer ferrite grains.The EBSD results indicated a strain gradient developed from the ferrite-martensite and ferrite-ferrite interfaces into the interior of ferrite grains during the tensile deformation,which led to a stress concentration at these interfaces.Moreover,it was demonstrated that local misorientation inside the finer ferrite grains surrounded by martensite islands was higher than that for the coarser ferrite grains,which made the former more prone to void initiation.
文摘Tribological behavior of nanostructured pure Al and Al–Al12（Fe,V）3Si alloys containing 27（FVS0812） and 37（FVS1212） vol% of Al12（Fe,V）3Si precipitates was investigated. All samples were prepared using mechanical alloying followed by hot pressing. Wear tests were performed at room temperature using a pin-on-disk machine. Results showed that the presence of Al12（Fe,V）3Si precipitates increases the wear resistance of nanostructured Al, and the wear resistance increases with increasing the Al12（Fe,V）3Si content. Scanning electron microscopy images of worn surfaces and wear debris demonstrated that abrasion and adhesion are the governing wear mechanisms for the nanostructured FVS0812 alloy at 2 and 5 N normal loads, whereas for the nanostructured FVS1212 alloy, the dominant wear mechanism is abrasion at these loads. A mechanically mixed layer（MML） containing Fe and O was formed on the worn surfaces of FVS0812 and FVS1212 samples at 10 N normal load. Formation and delamination of MML controls the wear behavior of these samples at the normal load of 10 N. It is also found that the presence of Al12（Fe,V）3Si precipitates decreases the friction coefficient of nanostructured Al.
