Towards tailoring basal texture of rolled Mg alloy sheet by recrystallization for high room-temperature formability: A review

Room-temperature(RT) formability is a key factor to broaden the applications of rolled Mg alloy sheets in the industry. However, rolled Mg alloy sheets generally form strong basal texture, where the(0001) poles align parallel to the normal direction(ND). This hinders the activation of(0001) [1120] basal slip, limiting the RT formability. Therefore, texture weakening, i.e., the inclination of the(0001) poles from the ND, plays an important role to improve the RT formability. Recrystallization is crucial to control the textural development in Mg,and currently, the texture weakening is commonly achieved using static recrystallization(SRX). However, the type of slipping and twinning,which are activated during rolling, affect the textural features after SRX. It is also demonstrated that shear bands and preferential grain growth are important factors to tailor the texture during SRX. Indeed, dynamic recrystallization(DRX) easily occurs during rolling in Mg, which also affects the final rolling texture, while the effect of DRX on the textural formation is not extensively studied for the development of RT-formable Mg alloy sheets. Therefore, the effect of these factors on the textural development in rolled Mg is reviewed in this manuscript.Additionally, the ideal microstructure and texture for RT-formable Mg alloy sheets are still controversial. The RT-formability includes stretch forming(biaxial tension), bending(plane strain tension), and deep-drawing. In particular, the stretch forming is commonly used to evaluate the RT-formability of rolled Mg. Although the stretch formability has been improved by recent studies, the further improvement is necessary owing to the relatively low formability of rolled Mg compared with that of rolled Fe and Al. Based on the relationship between the microstructure/texture and stretch formability provided in the literature, the design guidance for high stretch formability is proposed in this review.

Origin of extension twinning-mediated static recrystallization and unique parallel alignment of(0001) poles to transverse direction in Mg-3Al-0.4Mn(mass%) alloy sheet

The origin of unique parallel alignment of(0001) poles to transverse direction(TD) was investigated using Mg-3Al-0.4Mn(mass%)alloy sheets rolled with different process conditions. When rolling was performed with intermediate reheating, the alloy showed a sluggish static recrystallization(SRX) behavior during post-annealing, facilitating the nucleation and growth of statically recrystallized grains from extension twins. This resulted in the apparent texture component with the parallel alignment of the(0001) poles to the TD, and the sheet exhibited good ductility for both the rolling direction(RD) and TD. In contrast, continuous rolling without intermediate reheating led to the formation of severely deformed regions near double twins. SRX was promoted at such regions, forming a typical basal textural feature with weak RD-split of the(0001) poles. Although extension twins were formed after the continuous rolling, SRX was facilitated at the severely deformed regions with double twins, and the formation of the unique alignment of the(0001) poles to the TD was suppressed. The RD-split texture led to the large elongation to failure along the RD, while it along the TD decreased owing to the narrow distribution of the(0001)poles toward the TD, resulting in the in-plane anisotropy in ductility.

Enhancing strength and creep resistance of Mg-Gd-Y-Zn-Zr alloy by substituting Mn for Zr

The age-hardening behavior and mechanical properties of the extruded Mg-2Gd-1.2Y-0.5Zn(at.%)alloy with Zr or Mn additions were investigated.The results show that Mn added alloy exhibits more remarkable age-hardening response than Zr added alloy,which is attributed to the fact that partitioning of Mn into the β'phases,β'precipitates and long period stacking ordered(LPSO)phases leads to the decrement in(G d+Y)concentrations in the second phases,facilitating the precipitation during aging treatment.Both peak-aged alloys show bimodal microstructure comprising the fine DRXed grains with nano-sized β phases pinned at DRXed grain boundaries as well as coarse worked grains with strong fiber texture.High strength and good thermal stability were obtained in both peak-aged Mn and Zr added alloys.While the peak-aged Mn added alloy shows higher strength and superior creep resistance due to its denser β'precipitates,thin LPSO phases and γ'precipitates and higher area fraction of worked grains with strong fiber texture.The 0.2% tensile proof stress and ultimate tensile strength of peak-aged Mn added alloy reach up to 454 MPa and 508 MPa,respectively,with elongation of 3.2%at room temperature.The minimum creep rate of the peak-aged Mn added alloy at 250℃/150 MPa is 2.4 × 10^-8 s^-1,which is superior than previously reported extruded Mg-Gd based alloys.

Improvement of strength and ductility synergy in a room-temperature stretch-formable Mg-Al-Mn alloy sheet by twin-roll casting and low-temperature annealing

Strength and ductility synergy in an Mg-3mass%Al-Mn(AM30)alloy sheet was successfully improved via twin-roll casting and annealing at low-temperature.An AM30 alloy sheet produced by twin-roll casting,homogenization,hot-rolling,and subsequent annealing at 170℃ for 64 h exhibits a good 0.2%proof stress of 170 MPa and a large elongation to failure of 33.1%along the rolling direction.The sheet also shows in-plane isotropic tensile properties,and the 0.2%proof stress and elongation to failure along the transverse direction are 176 MPa and 35.5%,respectively.Though the sheet produced by direct-chill casting also shows moderate strengths if the annealing condition is same,the direct-chill casting leads to the deteriorated elongation to failure of 23.9%and 30.0%for the rolling and transverse directions,respectively.As well as such excellent tensile properties,a high room-temperature stretch formability with an Index Erichsen value of 8.3 mm could be obtained in the twin-roll cast sheet annealed at 170℃ for 64 h.The annealing at a higher temperature further improves the stretch formability;however,this results in the decrease of the tensile properties.Microstructure characterization reveals that the excellent combination of strengths,ductility,and stretch formability in the twin-roll cast sheet annealed at the low-temperature annealing is mainly attributed to the uniform recrystallized microstructure,fine grain size,and circular distribution of(0001)poles away from the normal direction of the sheet.

Quasi-in-situ observing the rare earth texture evolution in an extruded Mg-Zn-Gd alloy with bimodal microstructure

The static recrystallization and associated texture evolution were investigated in an extruded Mg-Zn-Gd alloy with bimodal microstructure based on a quasi-in-situ electron back-scatter diffraction(EBSD)method.The typical rare earth(RE)texture formed during annealing,evolving from the bimodal microstructure with[1010]basal fiber texture that consisted of fine recrystallized(RXed)grains and coarse unrecrystallized(un RXed)grains elongated along the extrusion direction.In both RXed and un RXed regions,the RXed nucleation produced randomized orientations without preferred selection and the RXed grains with RE texture orientation had more intensive growth ability than those with basal fiber orientation,thereby leading to the preferred selection of RE texture orientation during grain growth.The relationships between stored strain energy,solute drag,grain growth and texture evolution are discussed in detail.This study provided direct evidence of the RE texture evolution in an extruded Mg-RE alloy,which assists in understanding the formation mechanisms for RE texture during extrusion and better developing wrought Mg alloys with improved formability.

肝门部胆管癌R0切除后复发模式

背景：手术切除是肝门部胆管癌患者获得长期生存唯一手段。随着外科技术和围手术期处理的进步,肝门部胆管癌患者短期存活发生巨大改变。但由于术后高的复发率使患者的长期存率仍低。但对肝门部胆管癌根治性切除后复发模式研究较少。

Effect of forced-air cooling on the microstructure and age-hardening response of extruded Mg-Gd-Y-Zn-Zr alloy full with LPSO lamella

The homogenized Mg-8.2 Gd-3.8 Y-1.0 Zn-0.4 Zr(wt.%)alloy full of plate-shaped long period stacking ordered(LPSO)phases was hot extruded in the atmosphere and cooled by the forced-air,then the effect of forced-air cooling on the microstructure and age-hardening response of the alloy was investigated in this work.The results show that in comparison with the extruded sample cooling in the atmosphere,the forced-air cooling restricts dynamic recrystallization(DRX)and brings about finer dynamic recrystallized(DRXed)grain size,stronger basal texture and higher dislocation density.Furthermore,the forced-air cooling promotes the dynamic precipitation in the DRXed regions and facilitates formation of plate-shaped LPSO phases andγ’phases with smaller interspacing in the unrecrystallized(un DRXed)regions,then slightly restricts the precipitation ofβphases during aging.After peak-ageing treatment,the extruded sample with forced-air cooling shows superior tensile properties with a tensile yield strength of 439 MPa,an ultimate tensile strength of 493 MPa,and elongation to failure of 18.6%.

Optimization of Cu content for the development of high-performance T5-treated thixo-cast Al-7Si-0.5Mg-Cu(wt.%)alloy

Cu content has been successfully optimized in a thixo-cast and directly aged(T5-treatment)Al-7 Si-0.5 Mg(wt.%)alloy.Even after the 0.5%Cu addition,plate-like Al_(2)Cu(θ’)phases,which contribute to high strengths and large plasticity,are precipitated.The formation of a large fraction of Cu-containing brittle phases could be suppressed as well.Then,the Al-7Si-0.5Mg-0.5Cu alloy exhibits high ultimate tensile strength,0.2%proof stress,and elongation to failure of 296 MPa,209 MPa,and 8.8%,respectively.This results in a high quality index similar to that of solution-treated and subsequently aged(T6-treated)Al-7 Si-Mg alloys.A Cu addition over 1.0%further improves the strengths;however,this leads to poor ductility because of the high fraction of Cu-containing brittle phases.