为满足高能同步辐射光源(High Energy Photon Source,HEPS)束流位置测量的需求,研制了各种类型的束流位置探测器(Beam Position Monitor,BPM)。位置灵敏度系数是BPM的一项重要参数,通过它可以精确计算束流的位置。使用边界元法计算束流...为满足高能同步辐射光源(High Energy Photon Source,HEPS)束流位置测量的需求,研制了各种类型的束流位置探测器(Beam Position Monitor,BPM)。位置灵敏度系数是BPM的一项重要参数,通过它可以精确计算束流的位置。使用边界元法计算束流位置探测器的灵敏度系数,适用于在无法使用天线模拟束流进行实际测量和有限元软件进行模拟的场合。以HEPS储存环BPM的参数为例,首先用边界元法分析计算了具有圆形横截面的BPM的位置灵敏度系数,在此基础上,分析了椭圆形(HEPS增强器)与八边形(BEPCⅡ储存环)管道的系数。将该方法应用于BPM的设计与分析中,确定了高能光源增强器BPM纽扣电极的方位角和北京正负电子对撞机BPM的纽扣电极间距。此外,计算了上述BPM的位置灵敏度系数分布Mapping图。圆形管道BPM的位置灵敏度系数结果与解析值接近,相对误差在1%左右,椭圆形与八边形管道BPM的计算结果与实际测量结果的偏差都在2%左右,证明了边界元法计算束流位置探测器的位置灵敏度系数是一种可靠的方法,可用于BPM的设计与相关问题的分析。展开更多
In this paper,a specially designed Pancharatnam–Berry(PB)phase is used to fuse two-dimensional Airy-like beams to adjust and construct a new nano-interferometric field structure.The calculation results show that this...In this paper,a specially designed Pancharatnam–Berry(PB)phase is used to fuse two-dimensional Airy-like beams to adjust and construct a new nano-interferometric field structure.The calculation results show that this nano-interferometric structure is highly dependent on the PB phase parameterγand the ratio of pupil radius to beam waistβ.The flexible setting of the nano-field with adjustable size,spacing and internal details can be realized.In addition,we found that the longitudinal field components always keep a clear pattern.Hence,it is expected that the longitudinal field components can be applied to each application scene separately.展开更多
Introduction Pd/Ti double-layer thin film as non-evaporable getter(NEG)was deposited by sublimation,and its activation temperature was as low as 100℃.The Pd film was deposited in situ after Ti deposition to ensure no...Introduction Pd/Ti double-layer thin film as non-evaporable getter(NEG)was deposited by sublimation,and its activation temperature was as low as 100℃.The Pd film was deposited in situ after Ti deposition to ensure no oxidization on Ti film.Pumping speed test and characterization method The pumping speed of the coated pipe was measured by a pumping speed test system.The sticking factor was calculated by Molflow.The surface morphology was observed by a scanning electron microscope(SEM).The chemical composition of the film was measured by an energy-dispersive spectrum inbuilt with the SEM.The crystalline structure of the film was measured using grazing incidence X-ray diffraction.Conclusion It was found that the pumping performance of the Pd/Ti film still remained high after 15 times of activation.The maximum pumping speed after heating at 100℃for 24 h was 1.1 L/s cm^(2)and 0.49 L/s cm^(2)for H_(2)and CO,respectively.It can be concluded that the key to reducing the activation temperature of NEG materials is to enhance the oxidation resistance of the surface of NEG.展开更多
文摘为满足高能同步辐射光源(High Energy Photon Source,HEPS)束流位置测量的需求,研制了各种类型的束流位置探测器(Beam Position Monitor,BPM)。位置灵敏度系数是BPM的一项重要参数,通过它可以精确计算束流的位置。使用边界元法计算束流位置探测器的灵敏度系数,适用于在无法使用天线模拟束流进行实际测量和有限元软件进行模拟的场合。以HEPS储存环BPM的参数为例,首先用边界元法分析计算了具有圆形横截面的BPM的位置灵敏度系数,在此基础上,分析了椭圆形(HEPS增强器)与八边形(BEPCⅡ储存环)管道的系数。将该方法应用于BPM的设计与分析中,确定了高能光源增强器BPM纽扣电极的方位角和北京正负电子对撞机BPM的纽扣电极间距。此外,计算了上述BPM的位置灵敏度系数分布Mapping图。圆形管道BPM的位置灵敏度系数结果与解析值接近,相对误差在1%左右,椭圆形与八边形管道BPM的计算结果与实际测量结果的偏差都在2%左右,证明了边界元法计算束流位置探测器的位置灵敏度系数是一种可靠的方法,可用于BPM的设计与相关问题的分析。
文摘In this paper,a specially designed Pancharatnam–Berry(PB)phase is used to fuse two-dimensional Airy-like beams to adjust and construct a new nano-interferometric field structure.The calculation results show that this nano-interferometric structure is highly dependent on the PB phase parameterγand the ratio of pupil radius to beam waistβ.The flexible setting of the nano-field with adjustable size,spacing and internal details can be realized.In addition,we found that the longitudinal field components always keep a clear pattern.Hence,it is expected that the longitudinal field components can be applied to each application scene separately.
基金provided by National Development and Reform Commission(Grand No.发改高技(2017)2173号)
文摘Introduction Pd/Ti double-layer thin film as non-evaporable getter(NEG)was deposited by sublimation,and its activation temperature was as low as 100℃.The Pd film was deposited in situ after Ti deposition to ensure no oxidization on Ti film.Pumping speed test and characterization method The pumping speed of the coated pipe was measured by a pumping speed test system.The sticking factor was calculated by Molflow.The surface morphology was observed by a scanning electron microscope(SEM).The chemical composition of the film was measured by an energy-dispersive spectrum inbuilt with the SEM.The crystalline structure of the film was measured using grazing incidence X-ray diffraction.Conclusion It was found that the pumping performance of the Pd/Ti film still remained high after 15 times of activation.The maximum pumping speed after heating at 100℃for 24 h was 1.1 L/s cm^(2)and 0.49 L/s cm^(2)for H_(2)and CO,respectively.It can be concluded that the key to reducing the activation temperature of NEG materials is to enhance the oxidation resistance of the surface of NEG.
