Intracranial large artery embolism due to carotid thrombosis caused by a neck massager:A case report

BACKGROUND There are few reported cases of intracranial large artery embolism due to carotid thrombosis caused by a neck massager.Herein we report such a case.CASE SUMMARY A 49-year-old woman presented with left limb weakness and dysarthria after a history of neck massage for 1 mo.Neurological examination showed left central facial paralysis and left hemiparesis with a National Institutes of Health Stroke Scale score of 12.Brain magnetic resonance imaging revealed restricted diffusion on diffusion-weighted imaging in the right parietal and temporal lobes.Computed tomography angiography(CTA)indicated M3 segment embolism of the right middle cerebral artery.Neck CTA revealed thrombosis of the bilateral common carotid arteries.Carotid ultrasound showed thrombosis in the bilateral common carotid arteries(approximately 2 cm below the proximal end of the carotid sinus),and contrast-enhanced ultrasound did not suggest enhancement.No hypertension,diabetes,heart disease,vasculitis,or thrombophilia was found after admission.After 1 wk of treatment with aspirin 200 mg and atorvastatin 40 mg,a carotid ultrasound reexamination showed that the thrombosis had significantly reduced.CONCLUSION Neck massager may cause carotid artery thrombosis.

Prevalence of hepatitis C infection among intravenous drug users in Shanghai

AIM:To characterize the prevalence of hepatitis C virus(HCV)infection among Chinese intravenous drug users(IDUs).METHODS:A total of 432 adult IDUs(95 women and337 men)in Shanghai were included in the study.The third-generation Elecsys Anti-HCV assay(Roche Diagnostics GmbH,Sandhofer Strasse 116,D-68305,Mannheim,Germany)was used to screen for antibodies against HCV.The RIBA strip,a supplemental antiHCV test with high specificity,was performed on all of the samples that tested positive during the initial screening.All of the anti-HCV positive samples were analyzed with a Cobas TaqMan 48 Analyzer(Roche Diagnostics)for direct detection of HCV RNA.All of the HCV RNA-positive samples were sequenced for genotype determination.RESULTS:The preliminary screening identified 262(60.6%)subjects who were seropositive for HCV.Of the 62 females and 200 males seropositive subjects,16(16.7%)and 65(19.3%),respectively,were confirmed by RIBA,yielding an overall HCV seropositive rate of18.8%.Four female(6.5%)and 14 male(7.0%)subjects tested positive for HCV RNA,indicating an active infection rate of 4.2%for the entire study population.The 18 HCV RNA-positive serum samples were genotyped.Seven individuals were genotype 1b,and four were genotype 1a.One individual each was infected with genotypes 2a,2b and 3a.Four subjects were coinfected with multiple strains:two with genotypes 1a and 2a,and two with genotypes 1b and 2a.The active infection rate among HCV-seropositive individuals was22.2%,which was significantly lower than most estimates.CONCLUSION:The prevalence of HCV is relatively low among IDUs in Shanghai,with a spontaneous recovery rate much higher than previous estimates.

Superior machinability of steel enhanced with BN and MnS particles

The strategy that replacing part of MnS with BN was proposed in order to decrease the sulfur content in sulfur based free-cutting steel. The effects of BN and MnS inclusions on the microstructure and machinability of the steel were systematically investigated. The results show that most of the BN and MnS inclusions exist individually in the steel and only a small amount of them are in a composite state form- ing either isolated particles or clusters of particles. In the case of multi-phased steel, the theoretical calculation predicts that the volume of large BN particles should be 0.7 times of the volume of large MnS particles. The machinability of this type of BN and MnS alloy steel over a wide range of cutting speeds ranging from a low speed appropriate for drilling to a high speed appropriate for turning is confirmed as being equal to or superior to that of an MnS reference steel, even though the sulfur content in the composite steel is only half that of the MnS steel. The aptitude for cutting effect of 240 ppm nitrogen and 115 ppm boron in the composite steel is demonstrated to be equivalent or even better than 1000 ppm sulfur in MnS free-cutting steel.