Controlled Diffusion Solidification(CDS) is a promising process relied on mixing two liquid alloys of precisely controlled chemistry and temperature in order to produce a predetermined alloy composition. In this study...Controlled Diffusion Solidification(CDS) is a promising process relied on mixing two liquid alloys of precisely controlled chemistry and temperature in order to produce a predetermined alloy composition. In this study, the CDS was employed to prepare hypereutectic Al-20%Si(mass fraction) alloy using Al-30%Si and pure Al of different temperatures. The mixing rate was controlled using three small crucibles with a hole of different diameters in their bottom. The effect of mixing rate and temperature on the microstructure of the primary Si-phase during the mixing of molten Al and Al-30%Si was studied. The results showed that when the diameter of the small crucible bottom hole is 16 mm, a higher mass mixing rate 0.217 kg·s-1 would results in a lower stream velocity 0.414 m·s-1. Conversely a lower mass mixing rate 0.114 kg·s-1(the diameter of the small crucible bottom hole is 8 mm) would result in a higher fluid stream velocity 0.879 m·s-1. A lower mass mixing rate would be better to refine the primary Si than a higher mass mixing rate. Meanwhile, the morphology and distribution of primary Si could also be improved. Especially, when Al-30%Si alloy at 820 °C was mixed with pure Al at 670 °C in the case of a mass mixing rate of 0.114 kg·s-1 and a pouring temperature of 680 °C, the average size of the primary Si phase would be only 18.2 μm. Its morphology would mostly be octahedral and the primary Si would distribute uniformly in the matrix microstructure. The lower mass mixing rate(0.114 kg·s-1) will enhance the broken tendency of Al-30%Si steam and the mixing agitation of resultant melt, so the primary Si phase can be better refined.展开更多
In this study, Al-Mg-Al trilaminated thin plates were fabricated by one-pass hot rolling to improve the processing capacity and bonding strength of magne- sium alloy plates. The effects of processing parameters were i...In this study, Al-Mg-Al trilaminated thin plates were fabricated by one-pass hot rolling to improve the processing capacity and bonding strength of magne- sium alloy plates. The effects of processing parameters were investigated. The results show that the optimal bonding strength is up to 20 MPa with a reduction ratio of 40 % and rolling temperature of 400 ℃, superior than that in other one-pass rolling studies with regard to thin lami- nated plates. In addition, a favorable property is achieved with the annealing temperature of 250-300 ℃ or annealing time of 1.5 h. When the annealing temperature exceeds 300 ℃ or annealing time exceeds 1.5 h, respectively, the bonding strength of Al/Mg/Al plate decreases. The scan- ning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analyses suggest that the appearance of thin diffusion layers between Al and Mg interfaces is helpful to improve the bonding strength, while the presence of thick diffusion layer would reduce the bonding strength greatly.展开更多
In order to discover new molecules with good insecticidal activities, a series of anthranilic diamides containing polyfluoroalkyl pyrazole were designed and synthesized, and their structures were characterized by1 H N...In order to discover new molecules with good insecticidal activities, a series of anthranilic diamides containing polyfluoroalkyl pyrazole were designed and synthesized, and their structures were characterized by1 H NMR and HRMS. Bioassays demonstrated that some of the title compound exhibited excellent insecticidal activities. The larvicidal activities of compound 8a, 8c, 8g, 8k and 8l against Mythimna separata Walker were 100% at 0.8 mg/L. The insecticidal activities of compound 8a, 8c,8e, 8g, 8k and 8l against Plutella xylostella Linnaeus were 100% at 0.4 mg/L. Surprisingly compounds 8a and 8c still showed 100% larvicidal activities against Plutella xylostella Linnaeus at 0.08 mg/L comparable to the commercialized Chlorantraniliprole. The LC_(50) of compound 8a and 8c against M. separata is 0.048 and 0.043 mg/L respectively.展开更多
Twenty six novel pyrimidin-4-amine derivatives containing the 1,2,4-oxadiazole motif were synthesized. Their chemical structures were confirmed by ^(1)H nuclear magnetic resonance (NMR), ^(13)C NMR, and high-resolutio...Twenty six novel pyrimidin-4-amine derivatives containing the 1,2,4-oxadiazole motif were synthesized. Their chemical structures were confirmed by ^(1)H nuclear magnetic resonance (NMR), ^(13)C NMR, and high-resolution mass spectrography. The insecticidal activity results indicated that some of them possessed excellent insecticidal activity (100%) against Mythimna separate, especially for compounds 6d, 6f, 6o, 6w, 6y and 6z. These compounds exhibited no activity against the insects Aphis medicagini and Tetranychus cinnabarinus. The structure- insecticidal activity relationships are discussed. Density functional theory analysis can potentially be used to design more active compounds. These results provide useful insecticide design information for further optimization.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.51064017 and 51464031)
文摘Controlled Diffusion Solidification(CDS) is a promising process relied on mixing two liquid alloys of precisely controlled chemistry and temperature in order to produce a predetermined alloy composition. In this study, the CDS was employed to prepare hypereutectic Al-20%Si(mass fraction) alloy using Al-30%Si and pure Al of different temperatures. The mixing rate was controlled using three small crucibles with a hole of different diameters in their bottom. The effect of mixing rate and temperature on the microstructure of the primary Si-phase during the mixing of molten Al and Al-30%Si was studied. The results showed that when the diameter of the small crucible bottom hole is 16 mm, a higher mass mixing rate 0.217 kg·s-1 would results in a lower stream velocity 0.414 m·s-1. Conversely a lower mass mixing rate 0.114 kg·s-1(the diameter of the small crucible bottom hole is 8 mm) would result in a higher fluid stream velocity 0.879 m·s-1. A lower mass mixing rate would be better to refine the primary Si than a higher mass mixing rate. Meanwhile, the morphology and distribution of primary Si could also be improved. Especially, when Al-30%Si alloy at 820 °C was mixed with pure Al at 670 °C in the case of a mass mixing rate of 0.114 kg·s-1 and a pouring temperature of 680 °C, the average size of the primary Si phase would be only 18.2 μm. Its morphology would mostly be octahedral and the primary Si would distribute uniformly in the matrix microstructure. The lower mass mixing rate(0.114 kg·s-1) will enhance the broken tendency of Al-30%Si steam and the mixing agitation of resultant melt, so the primary Si phase can be better refined.
基金financially supported by the National Natural Science Foundation of China (Nos.51301118 and 51175363)the Specialized Research Fund for the Doctoral Program of Higher Education (No.20050112001)the Natural Science Foundation of Shanxi Province (No. 2006011051)
文摘In this study, Al-Mg-Al trilaminated thin plates were fabricated by one-pass hot rolling to improve the processing capacity and bonding strength of magne- sium alloy plates. The effects of processing parameters were investigated. The results show that the optimal bonding strength is up to 20 MPa with a reduction ratio of 40 % and rolling temperature of 400 ℃, superior than that in other one-pass rolling studies with regard to thin lami- nated plates. In addition, a favorable property is achieved with the annealing temperature of 250-300 ℃ or annealing time of 1.5 h. When the annealing temperature exceeds 300 ℃ or annealing time exceeds 1.5 h, respectively, the bonding strength of Al/Mg/Al plate decreases. The scan- ning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analyses suggest that the appearance of thin diffusion layers between Al and Mg interfaces is helpful to improve the bonding strength, while the presence of thick diffusion layer would reduce the bonding strength greatly.
基金supported by Key Projects of the National Science and Technology Pillar Program of China(No.2011BAE06B01-20)
文摘In order to discover new molecules with good insecticidal activities, a series of anthranilic diamides containing polyfluoroalkyl pyrazole were designed and synthesized, and their structures were characterized by1 H NMR and HRMS. Bioassays demonstrated that some of the title compound exhibited excellent insecticidal activities. The larvicidal activities of compound 8a, 8c, 8g, 8k and 8l against Mythimna separata Walker were 100% at 0.8 mg/L. The insecticidal activities of compound 8a, 8c,8e, 8g, 8k and 8l against Plutella xylostella Linnaeus were 100% at 0.4 mg/L. Surprisingly compounds 8a and 8c still showed 100% larvicidal activities against Plutella xylostella Linnaeus at 0.08 mg/L comparable to the commercialized Chlorantraniliprole. The LC_(50) of compound 8a and 8c against M. separata is 0.048 and 0.043 mg/L respectively.
基金funded by the Zhejiang Provincial Natural Science Foundation of China(Grant No.LY19C140002)the Company of Three Win(Grant No.KYY-HX-20200746)Research Fund of Department of Education of Zhejiang Province(Grant No.Y202043162).
文摘Twenty six novel pyrimidin-4-amine derivatives containing the 1,2,4-oxadiazole motif were synthesized. Their chemical structures were confirmed by ^(1)H nuclear magnetic resonance (NMR), ^(13)C NMR, and high-resolution mass spectrography. The insecticidal activity results indicated that some of them possessed excellent insecticidal activity (100%) against Mythimna separate, especially for compounds 6d, 6f, 6o, 6w, 6y and 6z. These compounds exhibited no activity against the insects Aphis medicagini and Tetranychus cinnabarinus. The structure- insecticidal activity relationships are discussed. Density functional theory analysis can potentially be used to design more active compounds. These results provide useful insecticide design information for further optimization.