Two-dimensional rigid-plastic finite element method (FEM) was used for simulation of the effect of process parameterson the static recrystallization of 60SiMnA spring steel using MARC/AutoForge 3.1 software. A thermo-...Two-dimensional rigid-plastic finite element method (FEM) was used for simulation of the effect of process parameterson the static recrystallization of 60SiMnA spring steel using MARC/AutoForge 3.1 software. A thermo-mechanicalcoupled analysis was conducted considering the heat transfer between the workpiece, the roll and the environment,and the heat generation due to plastic work. The static recrystallization laws under different processing conditionsand the predicted distribution of the static recrystallization volume fraction on the deformation cross section arepresented.展开更多
Mechanical properties and microstructure changes have been investigated on anew nickel-base superalloy after long-term aging at 700 deg C. It is found that the majorprecipitates of the tested alloy are MC, M_(23)C_6, ...Mechanical properties and microstructure changes have been investigated on anew nickel-base superalloy after long-term aging at 700 deg C. It is found that the majorprecipitates of the tested alloy are MC, M_(23)C_6, M_6C and y' in the course of long4erm aging at700 deg C. The carbides maintain good thermal stability with the aging time up to 5008 h. The growthrate of gamma prime precipitates is relatively high in the early aging period and then slows down.The coarsening behavior of gamma prime follows a diffusion-controlled growth procedure. The roomtemperature Rockwell hardness of the alloy aged at 700 deg C increases slightly at the initial stageof aging, but it decreases with the prolonged time. It mainly depends on the size of gamma prime.In comparison with Nimonic alloy 263, the new alloy characterizes with higher tensile andstress-rupture strengths at high temperatures. The new nickel-base superalloy offers a combinationof microstructure stability, strength, ductility and toughness at 700 deg C.展开更多
A model is developed for predicting the correlation between processing parameters and the technical target of double glow by applying artificial neural network (ANN). The input parameters of the neural network (NN) ar...A model is developed for predicting the correlation between processing parameters and the technical target of double glow by applying artificial neural network (ANN). The input parameters of the neural network (NN) are source voltage, workplace voltage, working pressure and distance between source electrode and workpiece. The output of the NN model is three important technical targets, namely the gross element content, the thickness of surface alloying layer and the absorption rate (the ratio of the mass loss of source materials to the increasing mass of workpiece) in the processing of double glow plasma surface alloying. The processing parameters and technical target are then used as a training set for an artificial neural network. The model is based on multiplayer feedforward neural network. A very good performance of the neural network is achieved and the calculated results are in good agreement with the experimental ones.展开更多
The 3-D thermo-mechanical coupled elasto-plastic finite element method (FEM)was used for the simulation of the two-pass continuous hot rolling process of 60SiMnA spring steelbars and rods using MARC/AutoForge3.1 softw...The 3-D thermo-mechanical coupled elasto-plastic finite element method (FEM)was used for the simulation of the two-pass continuous hot rolling process of 60SiMnA spring steelbars and rods using MARC/AutoForge3.1 software. The simulated results visualize the metal flow andthe dynamic evolutions of the strain, stress and temperature during the continuous hot rolling,especially inside the work-piece. It is shown that the non-uniform distributions of the strain,stress and temperature on the longitudinal and transverse sections are a distinct characteristic ofthe continuous hot rolling, which can be used as basic data for improving the tool design,predicting and controlling the micro-structural evolution of a bar and rod.展开更多
The Ni-Cr-Mo-Cu multi-element surface alloying with the electric brushplating Ni interlayer on the low carbon steel substrate has been investigated. By theelectrochemical method in 3.5 percent (mass fraction) NaCl sol...The Ni-Cr-Mo-Cu multi-element surface alloying with the electric brushplating Ni interlayer on the low carbon steel substrate has been investigated. By theelectrochemical method in 3.5 percent (mass fraction) NaCl solution, the corrosion resistance of thecomposite alloying layer and single alloying layer is determined. The experimental results showthat the corrosion resistance of the composite alloying layer is obviously better than that of thesingle alloying layer. The structure and composition of passive films formed on the two kinds ofalloyed layers after electrochemical tests in 3.5 percent NaCl solution have been studied usingX-ray photoelectron spectroscopy (XPS). It is concluded that the double glow plasma surface alloyingof low carbon steel with the electric brush plating Ni interlayer is an appropriate technique toenhance the corrosion resistance compared with the single double glow surface alloying.展开更多
In order to further understand the similarity and difference betweendeformation mechanisms of single crystals and poly-crystalline materials, the influence of externalconstraint and rolling geometry on the deformation...In order to further understand the similarity and difference betweendeformation mechanisms of single crystals and poly-crystalline materials, the influence of externalconstraint and rolling geometry on the deformation behaviour of copper single crystals with{123}<634> orientation was investigated by embedding them into metal frames of different strengths.The metal frames were made of aluminum and mild steel, respectively. The results show that thedeformation banding degree of the crystal increases with the strength of metal frame and shearstrain. For the crystals rolled under lower (gamma)g ((gamma)g is the ratio of the geometricalredundant shear strain to the normal rolling strain), the deformation is homogeneous. For thecrystals rolled under higher (gamma)g, the deformation is extremely inhomogeneous. The deformationis more homogeneous in the crystals rolled in steel frames than that rolled in aluminum frames. TheS-orientation is more stable in the crystals rolled under lower (gamma)g than that rolled underhigher (gamma)g.展开更多
文摘Two-dimensional rigid-plastic finite element method (FEM) was used for simulation of the effect of process parameterson the static recrystallization of 60SiMnA spring steel using MARC/AutoForge 3.1 software. A thermo-mechanicalcoupled analysis was conducted considering the heat transfer between the workpiece, the roll and the environment,and the heat generation due to plastic work. The static recrystallization laws under different processing conditionsand the predicted distribution of the static recrystallization volume fraction on the deformation cross section arepresented.
文摘Mechanical properties and microstructure changes have been investigated on anew nickel-base superalloy after long-term aging at 700 deg C. It is found that the majorprecipitates of the tested alloy are MC, M_(23)C_6, M_6C and y' in the course of long4erm aging at700 deg C. The carbides maintain good thermal stability with the aging time up to 5008 h. The growthrate of gamma prime precipitates is relatively high in the early aging period and then slows down.The coarsening behavior of gamma prime follows a diffusion-controlled growth procedure. The roomtemperature Rockwell hardness of the alloy aged at 700 deg C increases slightly at the initial stageof aging, but it decreases with the prolonged time. It mainly depends on the size of gamma prime.In comparison with Nimonic alloy 263, the new alloy characterizes with higher tensile andstress-rupture strengths at high temperatures. The new nickel-base superalloy offers a combinationof microstructure stability, strength, ductility and toughness at 700 deg C.
文摘A model is developed for predicting the correlation between processing parameters and the technical target of double glow by applying artificial neural network (ANN). The input parameters of the neural network (NN) are source voltage, workplace voltage, working pressure and distance between source electrode and workpiece. The output of the NN model is three important technical targets, namely the gross element content, the thickness of surface alloying layer and the absorption rate (the ratio of the mass loss of source materials to the increasing mass of workpiece) in the processing of double glow plasma surface alloying. The processing parameters and technical target are then used as a training set for an artificial neural network. The model is based on multiplayer feedforward neural network. A very good performance of the neural network is achieved and the calculated results are in good agreement with the experimental ones.
文摘The 3-D thermo-mechanical coupled elasto-plastic finite element method (FEM)was used for the simulation of the two-pass continuous hot rolling process of 60SiMnA spring steelbars and rods using MARC/AutoForge3.1 software. The simulated results visualize the metal flow andthe dynamic evolutions of the strain, stress and temperature during the continuous hot rolling,especially inside the work-piece. It is shown that the non-uniform distributions of the strain,stress and temperature on the longitudinal and transverse sections are a distinct characteristic ofthe continuous hot rolling, which can be used as basic data for improving the tool design,predicting and controlling the micro-structural evolution of a bar and rod.
文摘The Ni-Cr-Mo-Cu multi-element surface alloying with the electric brushplating Ni interlayer on the low carbon steel substrate has been investigated. By theelectrochemical method in 3.5 percent (mass fraction) NaCl solution, the corrosion resistance of thecomposite alloying layer and single alloying layer is determined. The experimental results showthat the corrosion resistance of the composite alloying layer is obviously better than that of thesingle alloying layer. The structure and composition of passive films formed on the two kinds ofalloyed layers after electrochemical tests in 3.5 percent NaCl solution have been studied usingX-ray photoelectron spectroscopy (XPS). It is concluded that the double glow plasma surface alloyingof low carbon steel with the electric brush plating Ni interlayer is an appropriate technique toenhance the corrosion resistance compared with the single double glow surface alloying.
文摘In order to further understand the similarity and difference betweendeformation mechanisms of single crystals and poly-crystalline materials, the influence of externalconstraint and rolling geometry on the deformation behaviour of copper single crystals with{123}<634> orientation was investigated by embedding them into metal frames of different strengths.The metal frames were made of aluminum and mild steel, respectively. The results show that thedeformation banding degree of the crystal increases with the strength of metal frame and shearstrain. For the crystals rolled under lower (gamma)g ((gamma)g is the ratio of the geometricalredundant shear strain to the normal rolling strain), the deformation is homogeneous. For thecrystals rolled under higher (gamma)g, the deformation is extremely inhomogeneous. The deformationis more homogeneous in the crystals rolled in steel frames than that rolled in aluminum frames. TheS-orientation is more stable in the crystals rolled under lower (gamma)g than that rolled underhigher (gamma)g.