Data exchange between different mode channels is essential in the optical communication network with mode-division multiplexing(MDM).However,there are challenges in realizing mode exchange with low insert loss,low mod...Data exchange between different mode channels is essential in the optical communication network with mode-division multiplexing(MDM).However,there are challenges in realizing mode exchange with low insert loss,low mode crosstalk,and high integration.Here,we designed and fabricated a mode exchange device based on multiplane light conversion(MPLC),which supports the transmission of LP01,LP11a,LP11b,and LP21 modes in the C-band and L-band.The simulated exchanged mode purities are greater than 85%.The phase masks were fabricated on a silicon substrate to facilitate the integration with optical systems,with an insert loss of less than 2.2 dB and mode crosstalk below-21 dB due primarily to machining inaccuracies and alignment errors.We carried out an optical communication experiment with 10 Gbit/s OOK and QPSK data transmission at the wavelength of 1550 nm and obtained excellent performance with the device.It paves the way for flexible data exchange as a building block in MDM optical communication networks.展开更多
Space-division multiplexing based on few-mode multi-core fiber(FM-MCF)technology is expected to break the Shannon limit of a single-mode fiber.However,an FM-MCF is compact,and it is difficult to couple the beam to eac...Space-division multiplexing based on few-mode multi-core fiber(FM-MCF)technology is expected to break the Shannon limit of a single-mode fiber.However,an FM-MCF is compact,and it is difficult to couple the beam to each fiber core.3D waveguide devices have the advantages of low insertion loss and low cross talk in separating various spatial paths of multi-core fibers.Designing a 3D waveguide device for an FM-MCF requires considering not only higher-order modes transmission,but also waveguide bending.We propose and demonstrate a 3D waveguide device fabricated by femtosecond laser direct writing for various spatial path separations in an FM-MCF.The 3D waveguide device couples the LP01 and LP11a modes to the FM-MCF with an insertion loss below 3 dB and cross talk between waveguides below-36 dB.To test the performance of the 3D waveguide device,we demonstrate four-channel multiplexing communication with two LP modes and two cores in a 1-km few-mode sevencore fiber.The bit error rate curves show that the different degrees of bending of the waveguides result in a difference of approximately 1 dB in the power penalty.Femtosecond laser direct writing fabrication enables 3D waveguide devices to support high-order LP modes transmission and further improves FM-MCF communication.展开更多
基金supported by the Guangdong Major Project of Basic Research(No.2020B0301030009)the National Natural Science Foundation of China(Nos.U23A20372,61935013,62105215,and 62275171)+3 种基金the Shenzhen Peacock Plan(No.KQTD20170330110444030)the Stable Support Project of Shenzhen(Nos.20220810152651001 and 20220811103827001)the Natural Science Foundation of GuangdongProvince(Nos.2020A1515011185and 2022A1515011642)Shenzhen University(No.2019075)。
文摘Data exchange between different mode channels is essential in the optical communication network with mode-division multiplexing(MDM).However,there are challenges in realizing mode exchange with low insert loss,low mode crosstalk,and high integration.Here,we designed and fabricated a mode exchange device based on multiplane light conversion(MPLC),which supports the transmission of LP01,LP11a,LP11b,and LP21 modes in the C-band and L-band.The simulated exchanged mode purities are greater than 85%.The phase masks were fabricated on a silicon substrate to facilitate the integration with optical systems,with an insert loss of less than 2.2 dB and mode crosstalk below-21 dB due primarily to machining inaccuracies and alignment errors.We carried out an optical communication experiment with 10 Gbit/s OOK and QPSK data transmission at the wavelength of 1550 nm and obtained excellent performance with the device.It paves the way for flexible data exchange as a building block in MDM optical communication networks.
基金Guangdong Major Project of Basic Research(2020B0301030009)National Key Research and Development Program of China(2018YFB1801801,2018YFB1800901)+4 种基金National Natural Science Foundation of China(61935013,61975133,62075139,61705135,12047540,61835005,62175162,62105215)Natural Science Foundation of Guangdong Province(2020A1515011185)Science,Technology and Innovation Commission of Shenzhen Municipality(RCJC20200714114435063,KQJSCX20170727100838364,JCYJ20180507182035270,JCYJ20200109114018750)Shenzhen Peacock Plan(KQTD20170330110444030)Shenzhen University(2019075)。
文摘Space-division multiplexing based on few-mode multi-core fiber(FM-MCF)technology is expected to break the Shannon limit of a single-mode fiber.However,an FM-MCF is compact,and it is difficult to couple the beam to each fiber core.3D waveguide devices have the advantages of low insertion loss and low cross talk in separating various spatial paths of multi-core fibers.Designing a 3D waveguide device for an FM-MCF requires considering not only higher-order modes transmission,but also waveguide bending.We propose and demonstrate a 3D waveguide device fabricated by femtosecond laser direct writing for various spatial path separations in an FM-MCF.The 3D waveguide device couples the LP01 and LP11a modes to the FM-MCF with an insertion loss below 3 dB and cross talk between waveguides below-36 dB.To test the performance of the 3D waveguide device,we demonstrate four-channel multiplexing communication with two LP modes and two cores in a 1-km few-mode sevencore fiber.The bit error rate curves show that the different degrees of bending of the waveguides result in a difference of approximately 1 dB in the power penalty.Femtosecond laser direct writing fabrication enables 3D waveguide devices to support high-order LP modes transmission and further improves FM-MCF communication.
