As a core element in solar parabolic trough collector, the evaluated receiver often runs under severe thermal conditions. Worse still, the transient thermal load is more likely to cause structural deformation and dama...As a core element in solar parabolic trough collector, the evaluated receiver often runs under severe thermal conditions. Worse still, the transient thermal load is more likely to cause structural deformation and damage. This work develops an efficient transient multi-level multi-dimensional(M2) analysis method to address photo-thermal-elastic problems, thereby estimating transient thermal load and deformation for the receiver:(i) one-dimensional(1-D) thermo-hydraulic model is adopted to determine the transient thermo-hydraulic state,(ii) 3-D finite volume method(FVM) model for the receiver tube is established to obtain the real-time temperature distribution,(iii) 3-D finite element method(FEM) model is employed to make thermoelastic analysis. Based on this M2 method, the typical transient cases are conducted in cold-start, disturbed-operation and regulatedprocess. Three indicators(average temperature of the wall(ATW), radial temperature difference(RTD), circumferential temperature difference(CTD)) are defined for overall analysis of the receiver thermal load. It is found that in the transient process,receivers face response delay and endure significant thermal load fluctuation. The response time for a single HCE(heat collecting element) under lower mass flow rate(1.5 kg s-1) could sustain 280 s. During the cold-start stage(DNI=200 W m-2 to 800 W m-2), the maximum value of CTD in receiver is as high as 11.67℃, corresponding to a maximum deflection of 1.05 cm.When the mass flow rate decreases sharply by 80%, the CTD reaches 33.04℃, causing a 2.06-cm deflection. It should be pointed out that in the cold-start stage and the lower mass flow rate operation for solar parabolic trough collector, alleviating the transient thermal load and deformation is of importance for safely and efficiently running evaluated receiver.展开更多
In pressurized water reactor(PWR)system,the surgeline plays an important role in bonding the pressurizer and the primary circle.Some considerable problems,including the thermo-hydraulics,the thermal stratification and...In pressurized water reactor(PWR)system,the surgeline plays an important role in bonding the pressurizer and the primary circle.Some considerable problems,including the thermo-hydraulics,the thermal stratification and the accompanying thermal stress under transient conditions,pose risks to the surgeline integrity.Herein,a fully-coupled flow-heat-thermo-elasticity model was developed to investigate the transient behavior of thermo-hydraulic parameters and the thermal stratification phenomenon in PWR.To evaluate the nonuniformity of the stratified flow,a stratification degree indicatorζis introduced.It is found that during the outsurge flow,the increase of temperature variation will enlarge the temperature gradient on the wall,corresponding to a more serious deformation.In the cases of positive temperature variation,the higher temperature variation causes higher stratification degreeζ,and vice versa.The mass flow rate m and the stratification degree are in negative correlation.The local deformation can reach 1.802 cm under a 50 K temperature variation,while its location varies from case to case.More attention should be paid to the regulation between the highest deformation location and the surgeline thermo-hydraulic parameters.展开更多
基金supported by the National Natural Science Foundation of China (Grant No. 51776156)the Key Project of National Natural Science Foundation of China (Grant No. 51436007)+1 种基金111 Project (Grant No.B16038)the Fundamental Research Funds for the Central Universities(Grant No. xjj2018195)。
文摘As a core element in solar parabolic trough collector, the evaluated receiver often runs under severe thermal conditions. Worse still, the transient thermal load is more likely to cause structural deformation and damage. This work develops an efficient transient multi-level multi-dimensional(M2) analysis method to address photo-thermal-elastic problems, thereby estimating transient thermal load and deformation for the receiver:(i) one-dimensional(1-D) thermo-hydraulic model is adopted to determine the transient thermo-hydraulic state,(ii) 3-D finite volume method(FVM) model for the receiver tube is established to obtain the real-time temperature distribution,(iii) 3-D finite element method(FEM) model is employed to make thermoelastic analysis. Based on this M2 method, the typical transient cases are conducted in cold-start, disturbed-operation and regulatedprocess. Three indicators(average temperature of the wall(ATW), radial temperature difference(RTD), circumferential temperature difference(CTD)) are defined for overall analysis of the receiver thermal load. It is found that in the transient process,receivers face response delay and endure significant thermal load fluctuation. The response time for a single HCE(heat collecting element) under lower mass flow rate(1.5 kg s-1) could sustain 280 s. During the cold-start stage(DNI=200 W m-2 to 800 W m-2), the maximum value of CTD in receiver is as high as 11.67℃, corresponding to a maximum deflection of 1.05 cm.When the mass flow rate decreases sharply by 80%, the CTD reaches 33.04℃, causing a 2.06-cm deflection. It should be pointed out that in the cold-start stage and the lower mass flow rate operation for solar parabolic trough collector, alleviating the transient thermal load and deformation is of importance for safely and efficiently running evaluated receiver.
基金supported by the Open Project of State Key Laboratory of Nuclear Power Safety Monitoring Technology and Equipment(K-A2019.424)。
文摘In pressurized water reactor(PWR)system,the surgeline plays an important role in bonding the pressurizer and the primary circle.Some considerable problems,including the thermo-hydraulics,the thermal stratification and the accompanying thermal stress under transient conditions,pose risks to the surgeline integrity.Herein,a fully-coupled flow-heat-thermo-elasticity model was developed to investigate the transient behavior of thermo-hydraulic parameters and the thermal stratification phenomenon in PWR.To evaluate the nonuniformity of the stratified flow,a stratification degree indicatorζis introduced.It is found that during the outsurge flow,the increase of temperature variation will enlarge the temperature gradient on the wall,corresponding to a more serious deformation.In the cases of positive temperature variation,the higher temperature variation causes higher stratification degreeζ,and vice versa.The mass flow rate m and the stratification degree are in negative correlation.The local deformation can reach 1.802 cm under a 50 K temperature variation,while its location varies from case to case.More attention should be paid to the regulation between the highest deformation location and the surgeline thermo-hydraulic parameters.
