When the variable geometry hypersonic inlet is sealed with ceramic wafers,the cavity flows inside the sealing chamber can be affected by the boundary layer near the side wall.To study the influence of the boundary lay...When the variable geometry hypersonic inlet is sealed with ceramic wafers,the cavity flows inside the sealing chamber can be affected by the boundary layer near the side wall.To study the influence of the boundary layer thickness near the side wall on the flow and leakage characteristics in sealing chamber,the numerical calculation of the cavity flow in the sealing chamber under different inflow boundary layer thicknesses is carried out.The results show that three-dimensional cavity flow structures are close to being asymmetric,and the entrance pressure of the leakage path can also be affected by asymmetry;with the increase of the thickness of the boundary layer,the pressure at the cavity floor and the seal entrance decreases.Finally,the existing leakage prediction model is modified according to the distribution rule of the cavity floor and the flow properties in the leakage path.展开更多
Under hypersonic flight conditions,the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating.This paper proposes four cowl-lip blunting methods and studies the corresponding flow ch...Under hypersonic flight conditions,the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating.This paper proposes four cowl-lip blunting methods and studies the corresponding flow characteristics and performances of the generic hypersonic inlets by numerical simulation under the design conditions of a flight Mach number of 6 and an altitude of 26 km.The results show that the local shock interference patterns in the vicinity of the blunted cowl-lips have a substantial influence on the flow characteristics of the hypersonic inlets even though the blunting radius is very small,which contribute to a pronounced degradation of the inlet performance.The Equal Length blunting Manner(ELM)is the most optimal in that a nearly even reflection of the ramp shock produces an approximately straight and weak cowl reflection shock.The minimal total pressure loss,the lowest cowl drag,maximum mass-capture and the minimal aeroheating are achieved for the hypersonic inlet.For the other blunting manners,the ramp shock cannot reflect evenly and produces more curved cowl reflection shock.The Type V shock interference pattern occurs for the Cross Section Cutting blunting Manner(CSCM)and the strongest cowl reflection shock gives rise to the largest flow loss and drag.The cowl-lip blunted by the other two blunting manners is subjected to the shock interference pattern that transits with an increase in the blunting radius.Accordingly,the peak heat flux does not fall monotonously with the blunting radius increasing.Moreover,the cowl-lip surface suffers from severe aerothermal load when the shear layer or the supersonic jet impinges on the wall.展开更多
Two types of flow configurations with bleed their aerodynamic thermal loads and related in two-dimensional hypersonic flows flow structures at choked conditions. are numerically examined to investigate One is a turbul...Two types of flow configurations with bleed their aerodynamic thermal loads and related in two-dimensional hypersonic flows flow structures at choked conditions. are numerically examined to investigate One is a turbulent boundary layer flow without shock impingement where the effects of the slot angle are discussed, and the other is shock wave boundary layer in- teractions where the effects of slot angle and slot location relative to shock impingement point are surveyed. A key separation is induced by bleed barrier shock on the upstream slot wall, resulting in a localized maximum heat flux at the reattachment point. For slanted slots, the dominating flow patterns are not much affected by the change in slot angle, but vary dramatically with slot location relative to the shock impingement point. Different flow structures are found in the case of normal slot, such as a flow pattern similar to typical Laval nozzle flow, the largest separation bubble which is almost independent of the shock position. Its larger detached distance results in 20% lower stagnation heat flux on the downstream slot corner, but with much wider area suffering from severe thermal loads. In spite of the complexity of the flow patterns, it is clearly revealed that the heat flux generally rises with the slot location moving downstream, and an increase in slot angle from 20° to 40° reduces 50% the heat flux peak at the reattachment point in the slot passage. The results further indicate that the bleed does not raise the heat flux around the slot for all cases except for the area around the downstream slot corner. Among all bleed configurations, the slot angle of 40° located slightly upstream of the incident shock is regarded as the best.展开更多
The effects of boundary layer bleed on the scramjet thrust are studied in the present paper.A theoretical model is developed to evaluate the thrust increment and influencing factors.The thrust increment resulting from...The effects of boundary layer bleed on the scramjet thrust are studied in the present paper.A theoretical model is developed to evaluate the thrust increment and influencing factors.The thrust increment resulting from the bleed is dominated by the rise in total pressure recovery and bleed mass flow rate.The bleed mass flow rate exerts stronger impact on the engine thrust than the total pressure.According to current bleed design,it is a severe challenge for the engine to enhance its total pressure to maintain the original thrust when there is no bleeding.Furthermore,the initial total pressure recovery,fuel mass addition,combustion efficiency and area ratio of engine exit to entrance can affect the contributions of the bleeding to the thrust increment.The scramjet needs a higher rise in total pressure recovery to counteract the negative effect of bleed mass loss at higher initial total pressure recovery or larger area ratio of engine exit/entrance.More heat release results in a little lower demand on the rise in total pressure recovery for maintaining the scramjet thrust.These results will aid in understanding the fundamental mechanism of bleeding on engine thrust.展开更多
基金supported by the Opening Foundation of National State Key Laboratory of High Temperature Gas Dynamics(No.2021KF07)。
文摘When the variable geometry hypersonic inlet is sealed with ceramic wafers,the cavity flows inside the sealing chamber can be affected by the boundary layer near the side wall.To study the influence of the boundary layer thickness near the side wall on the flow and leakage characteristics in sealing chamber,the numerical calculation of the cavity flow in the sealing chamber under different inflow boundary layer thicknesses is carried out.The results show that three-dimensional cavity flow structures are close to being asymmetric,and the entrance pressure of the leakage path can also be affected by asymmetry;with the increase of the thickness of the boundary layer,the pressure at the cavity floor and the seal entrance decreases.Finally,the existing leakage prediction model is modified according to the distribution rule of the cavity floor and the flow properties in the leakage path.
基金supported by the National Natural Science Foundation of China(Grant Nos.90716014 and 91216115)
文摘Under hypersonic flight conditions,the sharp cowl-lip leading edges have to be blunted because of the severe aerodynamic heating.This paper proposes four cowl-lip blunting methods and studies the corresponding flow characteristics and performances of the generic hypersonic inlets by numerical simulation under the design conditions of a flight Mach number of 6 and an altitude of 26 km.The results show that the local shock interference patterns in the vicinity of the blunted cowl-lips have a substantial influence on the flow characteristics of the hypersonic inlets even though the blunting radius is very small,which contribute to a pronounced degradation of the inlet performance.The Equal Length blunting Manner(ELM)is the most optimal in that a nearly even reflection of the ramp shock produces an approximately straight and weak cowl reflection shock.The minimal total pressure loss,the lowest cowl drag,maximum mass-capture and the minimal aeroheating are achieved for the hypersonic inlet.For the other blunting manners,the ramp shock cannot reflect evenly and produces more curved cowl reflection shock.The Type V shock interference pattern occurs for the Cross Section Cutting blunting Manner(CSCM)and the strongest cowl reflection shock gives rise to the largest flow loss and drag.The cowl-lip blunted by the other two blunting manners is subjected to the shock interference pattern that transits with an increase in the blunting radius.Accordingly,the peak heat flux does not fall monotonously with the blunting radius increasing.Moreover,the cowl-lip surface suffers from severe aerothermal load when the shear layer or the supersonic jet impinges on the wall.
基金supported by the National Natural Science Foundation of China(Grant Nos.91216115 and 11472279)
文摘Two types of flow configurations with bleed their aerodynamic thermal loads and related in two-dimensional hypersonic flows flow structures at choked conditions. are numerically examined to investigate One is a turbulent boundary layer flow without shock impingement where the effects of the slot angle are discussed, and the other is shock wave boundary layer in- teractions where the effects of slot angle and slot location relative to shock impingement point are surveyed. A key separation is induced by bleed barrier shock on the upstream slot wall, resulting in a localized maximum heat flux at the reattachment point. For slanted slots, the dominating flow patterns are not much affected by the change in slot angle, but vary dramatically with slot location relative to the shock impingement point. Different flow structures are found in the case of normal slot, such as a flow pattern similar to typical Laval nozzle flow, the largest separation bubble which is almost independent of the shock position. Its larger detached distance results in 20% lower stagnation heat flux on the downstream slot corner, but with much wider area suffering from severe thermal loads. In spite of the complexity of the flow patterns, it is clearly revealed that the heat flux generally rises with the slot location moving downstream, and an increase in slot angle from 20° to 40° reduces 50% the heat flux peak at the reattachment point in the slot passage. The results further indicate that the bleed does not raise the heat flux around the slot for all cases except for the area around the downstream slot corner. Among all bleed configurations, the slot angle of 40° located slightly upstream of the incident shock is regarded as the best.
基金supported by the National Natural Science Foundation of China(Grant Nos.90716014 and 91216115)
文摘The effects of boundary layer bleed on the scramjet thrust are studied in the present paper.A theoretical model is developed to evaluate the thrust increment and influencing factors.The thrust increment resulting from the bleed is dominated by the rise in total pressure recovery and bleed mass flow rate.The bleed mass flow rate exerts stronger impact on the engine thrust than the total pressure.According to current bleed design,it is a severe challenge for the engine to enhance its total pressure to maintain the original thrust when there is no bleeding.Furthermore,the initial total pressure recovery,fuel mass addition,combustion efficiency and area ratio of engine exit to entrance can affect the contributions of the bleeding to the thrust increment.The scramjet needs a higher rise in total pressure recovery to counteract the negative effect of bleed mass loss at higher initial total pressure recovery or larger area ratio of engine exit/entrance.More heat release results in a little lower demand on the rise in total pressure recovery for maintaining the scramjet thrust.These results will aid in understanding the fundamental mechanism of bleeding on engine thrust.
