An internal circulation iron-carbon micro-electrolysis reactor for aniline wastewater treatment:Parameter optimization,degradation pathways and mechanism

Aniline is a vital industrial raw material.However,highly-toxic aniline wastewater usually deteriorated effluent quality,posed a threat to human health and ecosystem safety.Therefore,this study reported a novel internal circulation iron-carbon micro-electrolysis(ICE)reactor to treat aniline wastewater.The effects of reaction time,pH,aeration rate and iron-carbon(Fe/C)ratio on the removal rate of aniline and the chemical oxygen demand were investigated using single-factor experiments.This process exhibited high aniline degradation performance of approximately 99.86% under optimal operating conditions(reaction time=20 min,pH=3,aeration rate=0.5 m3·h^(-1),and Fe/C=1:2).Based on the experimental results,the response surface method was applied to optimize the aniline removal rate.The Box–Behnken method was used to obtain the interaction effects of three main factors.The result showed that the reaction time had a dominant effect on the removal rate of aniline.The highest aniline removal rate was obtained at pH of 2,aeration rate of 0.5 m^(3)·h^(-1)and reaction time of 30 min.Under optional experimental conditions,the aniline content of effluent was reduced to 3 mg·L^(-1)and the removal rate was as high as 98.24%,within the 95% confidence interval(97.84%-99.32%)of the predicted values.The solution was treated and the reaction intermediates were identified by high-performance liquid chromatography,ultraviolet-visible spectroscopy,Fourier-transform infrared spectroscopy,gas chromatography-mass spectrometry,and ion chromatography.The main intermediates were phenol,benzoquinone,and carboxylic acid.These were used to propose the potential mechanism of aniline degradation in the ICE reactor.The results obtained in this study provide optimized conditions for the treatment of industrial wastewater containing aniline and can strengthen the understanding of the degradation mechanism of iron-carbon micro-electrolysis.

Oil–water pre-separation with a novel axial hydrocyclone

A novel hydrocyclone with guide vanes, named as axial hydrocyclone(AHC), is designed to tackle the problem of oil–water separation faced by most mature oilfields. Optimal design of the AHC is carried out by using numerical methods. The effects of guide vanes, cone angle, tapered angle and overflow pipe on the oil–water separation are discussed in this paper. The results show that a double swirling flow is generated in the tapered section where oil–water separation occurs. Both the cylindrical and the tapered section have important influences on AHC performance. On the basis of single factor results, response surface methodology is employed to optimize the AHC design. The experimental results indicate that the novel AHC has an excellent performance for the oil–water separation.

Optimization of the N2 generation selectivity in aqueous nitrate reduction using internal circulation micro-electrolysis

The reduction of nitrate using internal circulation micro-electrolysis te chnology(ICE)was investigated.The effect of the reaction time,initial pH,Fe/C ratio,and aeration rate on the nitrate reduction was investigated using a single factor experiment.Based on the results of the single factor experiment,a response surface methodology(RSM)was applied to optimize the N2 generation selectivity.The effects and interactions of three independent variables were estimated using a Box-Behnken design.Using the RSM analysis,a quadratic polynomial model with optimal conditions at pH=8.8,Fe/C=1:1,and an aeration rate of 30 L·min-1 was developed by means of the regre ssion analysis of the experimental data.Using the RSM optimization,the optimal conditions yielded a N2 generation selectivity of 72.0%,which is in good agreement with experimental result(73.2%±0.5%)and falls within the 95%confidence interval(IC:66.8%-77.3%)of the model results.This indicates that the model obtained in this study effectively predicts the N2 generation selectivity for nitrate reduction by the ICE process,thus providing a theoretical basis for process design.

Structural parameter optimization for novel internal-loop iron–carbon micro-electrolysis reactors using computational fluid dynamics

It is generally recognized that internal-loop reactors are well-developed mass and heat-transfer multiphase flow reactors. However, the internal flow field in the internal-loop reactor is influenced by the structure parameter of the reactor, which has a great effect on the reaction efficiency. In this study, the computational fluid dynamics simulation method was used to determine the influence of reactor structure on flow field, and a volume-offluid model was employed to simulate the gas–liquid, two-phase flow of the internal-loop micro-electrolysis reactor. Hydrodynamic factors were optimized when the height-to-diameter ratio was 4:1, diameter ratio was9:1, draft-tube axial height was 90 mm. Three-dimensional simulations for the water distributor were carried out, and the results suggested that the optimal conditions are as follows: the number of water distribution pipes was four, and an inhomogeneous water distribution was used. According to the results of the simulation,the suitable structure can be used to achieve good fluid mechanical properties, such as the good liquid circulation velocity and gas holdup, which provides a good theoretical foundation for the application of the reactor.

Rutile TiO2 Microspheres with Exposed Nano-Acicular Single Crystals for Dye-Sensitized Solar Cells

有暴露的 nano 针状的单个晶体的特别地结构化的金红石 TiO2 microspheres 成功地经由一个灵巧的热水的方法被综合了。在在 450 点的锻烧以后？

Photoelectrocatalytic activity of an ordered and vertically aligned TiO2 nanorod array/BDD heterojunction electrode

Rutile TiO_2 nanorod(TiNR) arrays were fabricated on a boron-doped diamond(BDD) substrate by a simple hydrothermal synthesis method. A fluorine-doped tin oxide(FTO) electrode grown with TiNR arrays was also prepared using the same technology for comparison. Field-emission scanning electron microscopy results show that oriented TiNR arrays can grow vertically on the surface of BDD and FTO electrodes. TiNR arrays grown on both electrodes had the same length(3 μm). In comparison with the TiNR/FTO electrode, the TiNR/BDD electrode demonstrated a higher photoelectrocatalytic activity for the degradation of water and organic compounds, which is mostly attributed to the formation of a p-n heterojunction between the TiNR arrays and BDD at high potential, apart from the density of TiNR. A linear relationship between the photoelectrocatalytic current and the organic concentration can be observed on both electrodes. However, the linear range between net photoelectrocatalytic current values and organic compound concentrations for the TiNR/BDD electrode are much greater than those for the TiNR/FTO electrode, which makes the TiNR/BDD electrode a versatile material for the photocatalytic degradation and sensing of organic compounds.