Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dy...Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dynamic recrystallization mechanism and texture evolution were studied.The results show that the grain size of the alloy was obviously refined after rotary backward extrusion.As the circumferenlial strain rate increased,the dynamic recrystallization fraction gradually increased causing the grain size decreased and the distribution of microstructure became more uniform.At the same time,the texture of{0001},{10-10},{11-20}was weakened and the grain orientation distribution became more random.With the increase of circumferential strain rate,the discontinuous dynamic recrystallization mechanism became dominant,which promoted the weakening of texture and grain refinement of the alloy.展开更多
The AZ80 magnesium(Mg)alloy cabin component with high strength and excellent ductility was developed by W-shaped channel extrusion(WCE)at 350℃ and subsequent T6 heat treatment.The effect of WCE process on the microst...The AZ80 magnesium(Mg)alloy cabin component with high strength and excellent ductility was developed by W-shaped channel extrusion(WCE)at 350℃ and subsequent T6 heat treatment.The effect of WCE process on the microstructure and mechanical properties of the alloy was experimentally investigated,and the age-hardening behavior with microstructure evolution during heat treatment was revealed.Due to the introduction of multi-stage asymmetric extrusion and severe shear deformation along the annular channel,the average grain size of the WCE extruded alloy could be effectively refined to 4.7μm.Besides,theβphase particles were dynamically precipitated from the fine grain boundaries during extrusion,which hindered the grain growth,but worsen the material plasticity.After T6 treatment,the properties of component were eventually improved to a yield strength(YS)of 218 MPa and ultimate tensile strength(UTS)of 344 MPa with elongation(EL)of 14.5%.It was revealed that the rod/lath-and needle-shaped continuousβphase(CP)with finer size precipitated after T6 treatment was more effective in hindering the movement of dislocations and strengthened the alloy than lamellar discontinuousβphase(DP).The dispersed phase precipitated in the grains,the annihilation of dislocations,the uniformly distributed grains and the re-dissolution ofβphase particles at initial grain boundaries after T6 treatment greatly contributed to the ductility of alloy.Moreover,the T6 treatment also promoted the basal plane of most grains which were re-arranged to the extrusion direction,which promoted the possibility of non-basal slip activation and further improved the elongation of the alloy.As a result,the UTS and YS of the final component increased by 10%and the EL increased by 7%,respectively.展开更多
基金the National Natural Science Foundation of China(Grant No.51775520)the National Key Research and Development Plan(Grant No.2016YFB0301103-3).
文摘Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dynamic recrystallization mechanism and texture evolution were studied.The results show that the grain size of the alloy was obviously refined after rotary backward extrusion.As the circumferenlial strain rate increased,the dynamic recrystallization fraction gradually increased causing the grain size decreased and the distribution of microstructure became more uniform.At the same time,the texture of{0001},{10-10},{11-20}was weakened and the grain orientation distribution became more random.With the increase of circumferential strain rate,the discontinuous dynamic recrystallization mechanism became dominant,which promoted the weakening of texture and grain refinement of the alloy.
基金supported by the Shanxi Provincial Science and Technology Cooperation and Exchange Project(No.202104041101033)the special fund for Science and Technology Innovation Teams of Shanxi Province+1 种基金the Shanxi Province's Key Core Technology and Common Technology Research and Development Special Project(No.2020XXX015)the Ningbo Natural Science Foundation(Project 2021J231 and 2021J232).
文摘The AZ80 magnesium(Mg)alloy cabin component with high strength and excellent ductility was developed by W-shaped channel extrusion(WCE)at 350℃ and subsequent T6 heat treatment.The effect of WCE process on the microstructure and mechanical properties of the alloy was experimentally investigated,and the age-hardening behavior with microstructure evolution during heat treatment was revealed.Due to the introduction of multi-stage asymmetric extrusion and severe shear deformation along the annular channel,the average grain size of the WCE extruded alloy could be effectively refined to 4.7μm.Besides,theβphase particles were dynamically precipitated from the fine grain boundaries during extrusion,which hindered the grain growth,but worsen the material plasticity.After T6 treatment,the properties of component were eventually improved to a yield strength(YS)of 218 MPa and ultimate tensile strength(UTS)of 344 MPa with elongation(EL)of 14.5%.It was revealed that the rod/lath-and needle-shaped continuousβphase(CP)with finer size precipitated after T6 treatment was more effective in hindering the movement of dislocations and strengthened the alloy than lamellar discontinuousβphase(DP).The dispersed phase precipitated in the grains,the annihilation of dislocations,the uniformly distributed grains and the re-dissolution ofβphase particles at initial grain boundaries after T6 treatment greatly contributed to the ductility of alloy.Moreover,the T6 treatment also promoted the basal plane of most grains which were re-arranged to the extrusion direction,which promoted the possibility of non-basal slip activation and further improved the elongation of the alloy.As a result,the UTS and YS of the final component increased by 10%and the EL increased by 7%,respectively.