Influence of graphene oxide(GO)on microstructure and biodegradation of ZK30-xGO composites prepared by selective laser melting

Different graphene oxide(GO)contents were chosen as the addition to prepare ZK30-xGO composites by selective laser melting(SLM).The microstructure and biodegradation of the SLMed ZK30-xGO composites were investigated.The results indicated that(i)SLM effectively produced a small grain size,(ii)the incorporation of GO into ZK30 caused a further decrease in grain size,and(iii)GO has a strong effect on the formation of the MgZn2 precipitates.The SLMed ZK30-0.6GO had the lowest biodegradation rate,which is attributed to the fact that the effect of the increased grain refinement and decreased amount of the MgZn?precipitates counteracted the effect of the increased GO content on the biodegradation rate.Furthermore,the SLMed ZK30-xGO composites had good cytocompatibility.This work provided a novel approach to the composition design and fabrication of novel biodegradable GO reinforced Mg-based biomedical implants.

Strategyproof Facility Location with Limited Locations

We study the mechanism design of facility location problems.The problem is to design mechanisms to select a set of locations on which to build a set of facilities,aiming to optimize some system objective and achieve desirable properties based on the strategic agents'locations.The agents might have incentives to misreport their private locations,in order to minimize the costs(i.e.,the distance from the closest facility).We study the setting with limited locations,that is,the facilities can only be built on a given finite set of candidate locations,rather than the whole space.For locating a single facility and two facilities on a real line,we propose strategyproof mechanisms with tight approximation ratios,under the objectives of minimizing the total cost and the maximum cost.Further,we consider the problem of locating an obnoxious facility from which the agents want to stay as far away as possible,and derive tight bounds on the approximation ratio of strategyproof mechanisms.

Effect of grain refinement and crystallographic texture produced by friction stir processing on the biodegradation behavior of a Mg-Nd-Zn alloy

The application of a single pass of friction stir processing(FSP) to Mg-Nd-Zn alloy resulted in grain refinement, texture evolution and redistribution of second phases, which improved corrosion resistance.In this work, an as-rolled Mg-Nd-Zn alloy was subjected to FSP. The microstructure in the processed zone of the FS-400 rpm alloy exhibited refined grains, a more homogenous grain size distribution, less second phases, and stronger basal plane texture. The corrosion behavior assessed using immersion tests and electrochemical tests in Hank’s solution indicated that the FS-400 rpm alloy had a lower corrosion rate, which was attributed to the increase of basal plane intensity and grain refinement. The hardness was lowered slightly and the elongation was increased, which might be attributed to the redistribution of the crushed second phases.

Hot Deformation Behavior of a New Nuclear Use Reduced Activation Ferritic/Martensitic Steel

The hot deformation behavior and workability of a new reduced activation ferritic/martensitic steel named SIMP steel for accelerator-driven system were studied. The flow curve and its microstructure were studied at 900-1200 ℃ and strain rate range of 0.001-10 s^-1. The results showed that the deformation behavior of the SIMP steel during hot compression could be manifested by the Zener-Hollomon parameter in an exponent-type equation. Based on the obtained constitutive equation, the calculated flow stresses were in agreement with the experimentally measured ones, and the average activity energies Qdrv and QHw for the initiation of dynamic recrystallization and the peak strain were calculated to be 476.1 kJ/mol and 462.7 kJ/mol, respectively. Furthermore, based on the processing maps and microstructure evolution, the optimum processing condition for the SIMP steel was determined to be 1050-1200 ℃/0.001-0.1s^-1.

Biodegradation Behavior of Coated As-Extruded Mg–Sr Alloy in Simulated Body Fluid

As-extruded Mg-Sr alloy, a kind of promising biodegradable biomedical material, was coated using micro-arc oxidation and also using a phosphate conversion coating. The corrosion behaviors were investigated using Hanks' solution. The corrosion of the as-extruded Mg-Sr alloy became more serious with increasing immersion time;that is, the corrosion pits became more numerous, larger and deeper, The micro-arc oxidation coating and the phosphate conversion coating were effective in improving the corrosion resistance of the as-extruded Mg-Sr alloy. The micro-arc oxidation coating was much more effective. Moreover, the as-extruded Mg-Sr alloy and the coated as-extruded Mg-Sr alloy exhibited lower corrosion rates than the as-cast Mg-Sr alloy and the corresponding coated as-cast Mg-Sr alloy, indicating that the corrosion properties of the coated samples are dependent on their substrates. The finer microstructure of the substrate of the as-extruded condition corroded much slower. The corrosion resistance of the coated Mg-Sr alloy depended on the coating itself and on the microstructure of the substrate.