An NM400 wear-resistant steel was hot rolled and then the plates were heat-treated by direct quenching and tempering （DQT） and reheat quenching and tempering （RQT） techniques, respectively. The Charpy impact test ...An NM400 wear-resistant steel was hot rolled and then the plates were heat-treated by direct quenching and tempering （DQT） and reheat quenching and tempering （RQT） techniques, respectively. The Charpy impact test was carried out with an instrumented Charpy impact tester. The microstructure and fracture surface were investiga-ted by a combination of optical microscopy, transmission electron microscopy and scanning electron microscopy methods. It was found that the impact toughness of DQT specimen was much higher than that of RQT specimen. The microstructure of both DQT and RQT specimens was characterized by a mixture of tempered lath martensite and lower hainite. The lower bainite in DQT specimen extended into prior austenite grains and the content was higher than that in RQT specimen. The lower bainite in DOT specimen improved the impact toughness by increasing the proportion of large-angle boundaries and relieving the stress concentration at the crack tip. A number of fine and dis-persed carbides in DQT specimen also contributed to the improvement of the impact toughness.展开更多
With tensile test, impact test, and optical microscopy, the effect of thermomechanical controlled processing （TMCP） parameters on the microstructure and properties of Q460 steel was studied and analyzed. The TMCP pa...With tensile test, impact test, and optical microscopy, the effect of thermomechanical controlled processing （TMCP） parameters on the microstructure and properties of Q460 steel was studied and analyzed. The TMCP parameters for Q460q steel were optimized by laboratory experiments, and then, industrial trial was carried out. The result indicated that the microstructure and properties of the Q460q steel in industrial trial were in agreement with the results obtained in laboratory experiments and could meet the national standard of Q460q steel.展开更多
With mean yield（MY）criterion,an analytical solution of the collapse load for a defect-free pipe elbow under internal pressure is first obtained.It is a function of ratio of thickness to radius t0/r0,strain hardening...With mean yield（MY）criterion,an analytical solution of the collapse load for a defect-free pipe elbow under internal pressure is first obtained.It is a function of ratio of thickness to radius t0/r0,strain hardening exponent n,curvature influence factor mand ultimate tensile strength.The collapse load increases with the increase of m,and it is the same as the burst pressure of straight pipe if m=1is assumed.The MY-based solution is compared with those based on Tresca,Mises and twin shear stress（TSS）yield criteria,and the comparison indicates that Tresca and twin shear stress yield criteria predict a lower bound and an upper bound to the collapse load respectively.However,the MY-based solution lies just between the TSS and Tresca solutions,and almost has the same precision with the Mises solution.展开更多
基金Item Sponsored by National Natural Science Foundation of China(51074052)
文摘An NM400 wear-resistant steel was hot rolled and then the plates were heat-treated by direct quenching and tempering （DQT） and reheat quenching and tempering （RQT） techniques, respectively. The Charpy impact test was carried out with an instrumented Charpy impact tester. The microstructure and fracture surface were investiga-ted by a combination of optical microscopy, transmission electron microscopy and scanning electron microscopy methods. It was found that the impact toughness of DQT specimen was much higher than that of RQT specimen. The microstructure of both DQT and RQT specimens was characterized by a mixture of tempered lath martensite and lower hainite. The lower bainite in DQT specimen extended into prior austenite grains and the content was higher than that in RQT specimen. The lower bainite in DOT specimen improved the impact toughness by increasing the proportion of large-angle boundaries and relieving the stress concentration at the crack tip. A number of fine and dis-persed carbides in DQT specimen also contributed to the improvement of the impact toughness.
基金Item Sponsored by Hi-Tech Research and Development Program of China (2003AA33G010)
文摘With tensile test, impact test, and optical microscopy, the effect of thermomechanical controlled processing （TMCP） parameters on the microstructure and properties of Q460 steel was studied and analyzed. The TMCP parameters for Q460q steel were optimized by laboratory experiments, and then, industrial trial was carried out. The result indicated that the microstructure and properties of the Q460q steel in industrial trial were in agreement with the results obtained in laboratory experiments and could meet the national standard of Q460q steel.
基金Sponsored by National Natural Science Foundation of China(51074052,50734002)
文摘With mean yield（MY）criterion,an analytical solution of the collapse load for a defect-free pipe elbow under internal pressure is first obtained.It is a function of ratio of thickness to radius t0/r0,strain hardening exponent n,curvature influence factor mand ultimate tensile strength.The collapse load increases with the increase of m,and it is the same as the burst pressure of straight pipe if m=1is assumed.The MY-based solution is compared with those based on Tresca,Mises and twin shear stress（TSS）yield criteria,and the comparison indicates that Tresca and twin shear stress yield criteria predict a lower bound and an upper bound to the collapse load respectively.However,the MY-based solution lies just between the TSS and Tresca solutions,and almost has the same precision with the Mises solution.
