Cast Al alloys are widely employed for engine components,structural parts,gear box,chassis,etc.and subjected to mechanical cyclic load during operation.The accurate fatigue life prediction of these alloys is essential...Cast Al alloys are widely employed for engine components,structural parts,gear box,chassis,etc.and subjected to mechanical cyclic load during operation.The accurate fatigue life prediction of these alloys is essential for normal operation as fatigue cracks initiated during operation induce the lubrication oil leak and serious safety hazard.Microstructural heterogeneity,including shrinkage/gaspores and secondary phase particles,is the most detrimental factor that affects fatigue life of cast Al alloys.The approximate fatigue life cycles could be estimated based on the size distribution and locations of shrinkage pores/defects.The relationship between crack population and stress was reported by statistical distributions and the cumulative probability for cast Al alloys fail at a certain stress could be predicted by combination of Paris law and pore size distribution.Pore depth was found to dominate the stress field around the pore on the surface and the maximum stress increases sharply when the pore intercepted with the surface at its top.The microstructure of cast Al alloys usually is composed of primary Al dendrites,eutectic silicon,Fe-rich particles and other intermetallic particles are dependent upon alloy composition and heat treatment.The coalescence of microcracks initiated from the fractured secondary phases was clearly found and can accelerate the initiation and propagation of the fatigue cracks.A link between defect features and the fatigue strength needs to be established through a good understanding of the fatigue damage mechanisms associated with the microstructural features under specific loading conditions.This paper reviews the influences of shrinkage/gaspores and secondary phase particles,formed during casting process,on the fatigue life of Al-Si-Mg cast Al alloys.展开更多
Alumina ceramics are widely used in many fields such as cutting tools,laser shock materials,roadbed board and refractory.Herein,Al_(2)O_(3)ceramics are prepared by a low-cost pressureless sintering technology,using th...Alumina ceramics are widely used in many fields such as cutting tools,laser shock materials,roadbed board and refractory.Herein,Al_(2)O_(3)ceramics are prepared by a low-cost pressureless sintering technology,using the binary sintering aids of MgO and SiO_(2).The effects of sintering temperature and the ratio of binary sintering aids on the mechanical properties and microstructure of Al_(2)O_(3)ceramics are investigated.A spinel second phase(MgAl_(2)O_(4))is found out by the analysis of the results of XRD and EDS when MgO and SiO_(2)are introduced in the samples.The optimum properties are found when MgO content is 20 wt.%based on the total sintering aids and the sintering temperature is 1550℃.The bending strength and the bulk density reach a maximum value of 314 MPa and 3.73 g/cm^(3),respectively.The addition of appropriate amount of SiO_(2)makes the formation of liquid phase sintering and the removal of large pores.Meanwhile,a small amount of magnesium oxide doping has an effect on the grain refinement from the microstructure of the sample.Therefore,it is believed that MgO and SiO_(2)are the ideal sintering aids for promoting the densification and property of alumina ceramics.展开更多
Interdisciplinary research is an inevitable trend in scientific development and an important driving force to accelerate scientific and technological innovations.How to promote interdisciplinary research has always be...Interdisciplinary research is an inevitable trend in scientific development and an important driving force to accelerate scientific and technological innovations.How to promote interdisciplinary research has always been a common question and a challenge faced by science research funding agencies all over the world.展开更多
In the modern society,there is a strong demand for semiconductor chips,and the 4H polytype silicon carbide(4H-SiC)power device is a promising candidate for the next generation semiconductor chip,which can be used in v...In the modern society,there is a strong demand for semiconductor chips,and the 4H polytype silicon carbide(4H-SiC)power device is a promising candidate for the next generation semiconductor chip,which can be used in various power electronic systems.In order to improve the performance of the 4H-SiC power device,a novel ultrahigh-voltage(UHV)4H-SiC merged p-type/intrinsic/n-type(PiN)Schottky(MPS)diode with three-dimensional(3D)p-type buried layers(PBL)(3D-PBL MPS)is proposed and investigated by numerical simulation.The static forward conduction characteristics of the 3D-PBL MPS are similar to those of the conventional 4H-SiC MPS diode without the PBL(PBL-free MPS).However,when the 3D-PBL MPS is in the reverse blocking state,the 3D PBL can transfer the peak electric field(E_(peak))into a deeper position in the body of the epitaxial layer,and enhance the ability of the device to shield the high electric field at the Schottky contact interface(E_(S)),so that the reverse leakage current of the 3D-PBL MPS at 10 kV is only 0.002%of that of the PBL-free MPS.Meanwhile,the novel 3D-PBL MPS has overcome the disadvantage in the 4H-SiC MPS diode with the two-dimensional PBL(2D-PBL MPS),and the forward conduction characteristic of the 3D-PBL MPS will not get degenerated after the device converts from the reverse blocking state to the forward conduction state because of the special depletion layer variation mechanism depending on the 3D PBL.All the simulation results show that the novel UHV 3D-PBL MPS has excellent device performance.展开更多
基金Projects(11790282,U1534204,11572267,51804202,51705344)supported by the National Natural Science Foundation of ChinaProject(E2019210292)supported by the Natural Science Foundation of Hebei Province,China+6 种基金Project(A2019210204)supported by the National Natural Science Foundation for Distinguished Young Scholars,ChinaProject(KQTD20170810160424889)supported by the Shenzhen Peacock Team Program,ChinaProject(2019DB013)supported by the Key Research Project of Southern Xinjiang,ChinaProject(C201821)supported by the High Level Talent Support Project in Hebei,ChinaProject supported by the Youth Top-notch Talents Supporting Plan of Hebei Province,ChinaProject(MCMS-E-0519G04)supported by the State Key Laboratory of Mechanics and Control of Mechanical Structures,Nanjing University of Aeronautics and Astronautics,ChinaProject(201919)supported by the Open Fund of State Key Laboratory of Metastable Materials Science and Technology,Yanshan University,China。
文摘Cast Al alloys are widely employed for engine components,structural parts,gear box,chassis,etc.and subjected to mechanical cyclic load during operation.The accurate fatigue life prediction of these alloys is essential for normal operation as fatigue cracks initiated during operation induce the lubrication oil leak and serious safety hazard.Microstructural heterogeneity,including shrinkage/gaspores and secondary phase particles,is the most detrimental factor that affects fatigue life of cast Al alloys.The approximate fatigue life cycles could be estimated based on the size distribution and locations of shrinkage pores/defects.The relationship between crack population and stress was reported by statistical distributions and the cumulative probability for cast Al alloys fail at a certain stress could be predicted by combination of Paris law and pore size distribution.Pore depth was found to dominate the stress field around the pore on the surface and the maximum stress increases sharply when the pore intercepted with the surface at its top.The microstructure of cast Al alloys usually is composed of primary Al dendrites,eutectic silicon,Fe-rich particles and other intermetallic particles are dependent upon alloy composition and heat treatment.The coalescence of microcracks initiated from the fractured secondary phases was clearly found and can accelerate the initiation and propagation of the fatigue cracks.A link between defect features and the fatigue strength needs to be established through a good understanding of the fatigue damage mechanisms associated with the microstructural features under specific loading conditions.This paper reviews the influences of shrinkage/gaspores and secondary phase particles,formed during casting process,on the fatigue life of Al-Si-Mg cast Al alloys.
基金Projects(11772207,U2130128)supported by the National Natural Science Foundation of ChinaProjects(E2019210042,E2017210065)supported by the Natural Science Foundation of Hebei Province,China+3 种基金Project(QN2019137)supported by the Natural Science Foundation of the Hebei Education Department,ChinaProject(A2019210204)supported by the Natural Science Foundation of Hebei Province for Distinguished Young Scholars,ChinaProject(216Z4302G)supported by Central Government Guiding Local Science and Technology Development,ChinaProject supported by Youth Top-notch Talents Supporting Plan of Hebei Province,China。
文摘Alumina ceramics are widely used in many fields such as cutting tools,laser shock materials,roadbed board and refractory.Herein,Al_(2)O_(3)ceramics are prepared by a low-cost pressureless sintering technology,using the binary sintering aids of MgO and SiO_(2).The effects of sintering temperature and the ratio of binary sintering aids on the mechanical properties and microstructure of Al_(2)O_(3)ceramics are investigated.A spinel second phase(MgAl_(2)O_(4))is found out by the analysis of the results of XRD and EDS when MgO and SiO_(2)are introduced in the samples.The optimum properties are found when MgO content is 20 wt.%based on the total sintering aids and the sintering temperature is 1550℃.The bending strength and the bulk density reach a maximum value of 314 MPa and 3.73 g/cm^(3),respectively.The addition of appropriate amount of SiO_(2)makes the formation of liquid phase sintering and the removal of large pores.Meanwhile,a small amount of magnesium oxide doping has an effect on the grain refinement from the microstructure of the sample.Therefore,it is believed that MgO and SiO_(2)are the ideal sintering aids for promoting the densification and property of alumina ceramics.
文摘Interdisciplinary research is an inevitable trend in scientific development and an important driving force to accelerate scientific and technological innovations.How to promote interdisciplinary research has always been a common question and a challenge faced by science research funding agencies all over the world.
基金Project(F2020210016) supported by the Natural Science Foundation of Hebei,ChinaProject(620004153) supported by the National Natural Science Foundation of China。
文摘In the modern society,there is a strong demand for semiconductor chips,and the 4H polytype silicon carbide(4H-SiC)power device is a promising candidate for the next generation semiconductor chip,which can be used in various power electronic systems.In order to improve the performance of the 4H-SiC power device,a novel ultrahigh-voltage(UHV)4H-SiC merged p-type/intrinsic/n-type(PiN)Schottky(MPS)diode with three-dimensional(3D)p-type buried layers(PBL)(3D-PBL MPS)is proposed and investigated by numerical simulation.The static forward conduction characteristics of the 3D-PBL MPS are similar to those of the conventional 4H-SiC MPS diode without the PBL(PBL-free MPS).However,when the 3D-PBL MPS is in the reverse blocking state,the 3D PBL can transfer the peak electric field(E_(peak))into a deeper position in the body of the epitaxial layer,and enhance the ability of the device to shield the high electric field at the Schottky contact interface(E_(S)),so that the reverse leakage current of the 3D-PBL MPS at 10 kV is only 0.002%of that of the PBL-free MPS.Meanwhile,the novel 3D-PBL MPS has overcome the disadvantage in the 4H-SiC MPS diode with the two-dimensional PBL(2D-PBL MPS),and the forward conduction characteristic of the 3D-PBL MPS will not get degenerated after the device converts from the reverse blocking state to the forward conduction state because of the special depletion layer variation mechanism depending on the 3D PBL.All the simulation results show that the novel UHV 3D-PBL MPS has excellent device performance.
