Fe-Cr-Ni/Al-Si-Cu-Ni-Mg composite was taken as the experimental material. The chemical composition of interfacial layer was tested. The generation mechanism and influence of interfacial layer on the composite were ana...Fe-Cr-Ni/Al-Si-Cu-Ni-Mg composite was taken as the experimental material. The chemical composition of interfacial layer was tested. The generation mechanism and influence of interfacial layer on the composite were analyzed. The results indicated that the generation of interfacial layer is sensitive to temperature. Interfacial layer will generate rapidly when temperature reaches 500 ℃ or above. The interfacial layer is mainly composed of Al, Si, Cu, Fe, and Cr, element Ni distributes at the outward of the interfacial layer for the precipitate of Ni later than Si and Cu, and there is almost no diffusion of Ni during the solution treatment. During heat treatment process, unequal quantity changing of metal atom results in disperse or concentrated vacancies or holes near the matrix. The existence of interfacial layer will induce a decrease of compression strength and plasticity at room temperature and an increase of strength at higher temperature comparing with composite without interfacial layer.展开更多
The isothermal compression tests were carried out on Gleeble-3500 thermal-mechanical simulation machine in a temperature range of 298-473 K and strain rate range of 0.001-10 s^-1. The experimental results show that th...The isothermal compression tests were carried out on Gleeble-3500 thermal-mechanical simulation machine in a temperature range of 298-473 K and strain rate range of 0.001-10 s^-1. The experimental results show that the flow stress data are negatively correlated with temperature for temperature softening, and the strain rates sensitivity of this composite increases with elevating temperature. Based on the experimental data, Johnson-Cook, modified Johnson-Cook and Arrhenius constitutive models were established. The accuracy of these three constitutive models was analyzed and compared. The results show that the values predicted by Johnson-Cook model could not agree well with the experimental values. The prediction accuracy of Arrhenius model is higher than that of Johnson-Cook model but lower than that of the Modified Johnson-Cook model.展开更多
TiO2 nanotube（TiNT） arrays were deposited on boron-doped diamond films by a liquid-phase deposition method with ZnO nanorod arrays as the template.The different morphologies of TiNTs have been obtained by controllin...TiO2 nanotube（TiNT） arrays were deposited on boron-doped diamond films by a liquid-phase deposition method with ZnO nanorod arrays as the template.The different morphologies of TiNTs have been obtained by controlling the morphology of ZnO template.The X-ray diffraction and energy-dispersive X-ray analysis show that the ZnO nanorod array template has been removed in the TiNTs formation process.The crystalline quality of the TiNTs is improved by increasing the annealing temperature.The band gap of the TiNTs is about 3.25 eV estimated by the UV-Vis absorption spectroscopy,which is close to the value of bulk TiO2.In the photoluminescence spectrum,a broad visible emission in a range of ca.550-750 nm appears due to the surface oxygen vacancies and defects.展开更多
基金Funded by the Program of International S&T Cooperation(No.2013DFA51230)the Opening Subject Fund of Ningbo University(No.zj1226)
文摘Fe-Cr-Ni/Al-Si-Cu-Ni-Mg composite was taken as the experimental material. The chemical composition of interfacial layer was tested. The generation mechanism and influence of interfacial layer on the composite were analyzed. The results indicated that the generation of interfacial layer is sensitive to temperature. Interfacial layer will generate rapidly when temperature reaches 500 ℃ or above. The interfacial layer is mainly composed of Al, Si, Cu, Fe, and Cr, element Ni distributes at the outward of the interfacial layer for the precipitate of Ni later than Si and Cu, and there is almost no diffusion of Ni during the solution treatment. During heat treatment process, unequal quantity changing of metal atom results in disperse or concentrated vacancies or holes near the matrix. The existence of interfacial layer will induce a decrease of compression strength and plasticity at room temperature and an increase of strength at higher temperature comparing with composite without interfacial layer.
基金Funded by the Program of International S&T Cooperation(No.2013DFA51230)the Opening Subject Fund of Ningbo University(No.zj1226)
文摘The isothermal compression tests were carried out on Gleeble-3500 thermal-mechanical simulation machine in a temperature range of 298-473 K and strain rate range of 0.001-10 s^-1. The experimental results show that the flow stress data are negatively correlated with temperature for temperature softening, and the strain rates sensitivity of this composite increases with elevating temperature. Based on the experimental data, Johnson-Cook, modified Johnson-Cook and Arrhenius constitutive models were established. The accuracy of these three constitutive models was analyzed and compared. The results show that the values predicted by Johnson-Cook model could not agree well with the experimental values. The prediction accuracy of Arrhenius model is higher than that of Johnson-Cook model but lower than that of the Modified Johnson-Cook model.
基金Supported by the National Natural Science Foundation of China（Nos.51072066, 11247305）, the PhD Programs Foundation of Ministry of Education of China（No.20100061110083）, the Open Project of State Key Laboratory of Superhard Materials（Jilin University）, China（No.201213） and the Youth Fund of Science and Technology Department of Jiangxi Province, China （No.20131522040044）.
文摘TiO2 nanotube（TiNT） arrays were deposited on boron-doped diamond films by a liquid-phase deposition method with ZnO nanorod arrays as the template.The different morphologies of TiNTs have been obtained by controlling the morphology of ZnO template.The X-ray diffraction and energy-dispersive X-ray analysis show that the ZnO nanorod array template has been removed in the TiNTs formation process.The crystalline quality of the TiNTs is improved by increasing the annealing temperature.The band gap of the TiNTs is about 3.25 eV estimated by the UV-Vis absorption spectroscopy,which is close to the value of bulk TiO2.In the photoluminescence spectrum,a broad visible emission in a range of ca.550-750 nm appears due to the surface oxygen vacancies and defects.
