The chemical composition and high wear resistance of steel slag(SS)make it a potential alternative to traditional inorganic fillers.3-Aminopropyltriethoxysilane(KH550)modified steel slag(MSS)was successfully prepared,...The chemical composition and high wear resistance of steel slag(SS)make it a potential alternative to traditional inorganic fillers.3-Aminopropyltriethoxysilane(KH550)modified steel slag(MSS)was successfully prepared,and its application in epoxy(EP)anti-corrosion coating was introduced.Due to the grafting of silane coupling agent functional groups onto the surface of SS,MSS exhibited improved solubility in xylene organic solvent and reduced agglomeration.When the MSS content was 15 wt.%,the contact angle of the MSS/EP composite coating was 101°,and the abrasion was only 0.07 g,compared with 56.2°and 0.13 g,respectively,for the pure EP coating.The corrosion resistance of coatings was investigated by performing the electrochemical test(impedance)after immersion in a 3.5 wt.%NaCl solution.The electrochemical test results showed that the impedance modulus of the 15 wt.%MSS/EP composite coating at low frequency(Z_(f)=0.01 Hz)was approximately 1.08×10^(7)Ωcm^(2),which was two orders of magnitude higher than that of the pure EP coating.展开更多
It is important to make full use of waste generated in the iron and steel manufacturing process for energy saving,emission reduction,low carbon production and a circular economy.Based on research on different kinds of...It is important to make full use of waste generated in the iron and steel manufacturing process for energy saving,emission reduction,low carbon production and a circular economy.Based on research on different kinds of industrial solid wastes from Shougang Jingtang,wastes have been optimized for use in sintering.At first,basic tests for all kinds of solid wastes that may be used in sintering were carried out,including chemical composition,calorific value of a fuel,holding time at high temperatures,the sintering pot test,etc.The results show that the appropriate solid waste ratios for current sintering conditions are：steel slag〈5%,scale 2.0%,environmental ash 2.0%,and cyclone ash 1.0%;blast furnace dry ash,sintering electric field ash,and steelmaking ash should not be circulated in sintering.As for the fuel structure,both coking ash and nut coke should be below 15%.By optimizing the addition of solid wastes,the damage of harmful elements to sintering and blast furnaces has been significantly reduced,which satisfies the demands for blast furnace materials and earns benefits.The utilization of solid wastes has made a contribution to the circular economy and sustainable development.展开更多
基金the University Synergy Innovation Program of Anhui Province(GXXT-2020-072).
文摘The chemical composition and high wear resistance of steel slag(SS)make it a potential alternative to traditional inorganic fillers.3-Aminopropyltriethoxysilane(KH550)modified steel slag(MSS)was successfully prepared,and its application in epoxy(EP)anti-corrosion coating was introduced.Due to the grafting of silane coupling agent functional groups onto the surface of SS,MSS exhibited improved solubility in xylene organic solvent and reduced agglomeration.When the MSS content was 15 wt.%,the contact angle of the MSS/EP composite coating was 101°,and the abrasion was only 0.07 g,compared with 56.2°and 0.13 g,respectively,for the pure EP coating.The corrosion resistance of coatings was investigated by performing the electrochemical test(impedance)after immersion in a 3.5 wt.%NaCl solution.The electrochemical test results showed that the impedance modulus of the 15 wt.%MSS/EP composite coating at low frequency(Z_(f)=0.01 Hz)was approximately 1.08×10^(7)Ωcm^(2),which was two orders of magnitude higher than that of the pure EP coating.
文摘It is important to make full use of waste generated in the iron and steel manufacturing process for energy saving,emission reduction,low carbon production and a circular economy.Based on research on different kinds of industrial solid wastes from Shougang Jingtang,wastes have been optimized for use in sintering.At first,basic tests for all kinds of solid wastes that may be used in sintering were carried out,including chemical composition,calorific value of a fuel,holding time at high temperatures,the sintering pot test,etc.The results show that the appropriate solid waste ratios for current sintering conditions are：steel slag〈5%,scale 2.0%,environmental ash 2.0%,and cyclone ash 1.0%;blast furnace dry ash,sintering electric field ash,and steelmaking ash should not be circulated in sintering.As for the fuel structure,both coking ash and nut coke should be below 15%.By optimizing the addition of solid wastes,the damage of harmful elements to sintering and blast furnaces has been significantly reduced,which satisfies the demands for blast furnace materials and earns benefits.The utilization of solid wastes has made a contribution to the circular economy and sustainable development.
