Effect of Microstructure Refinement on the Strength and Toughness of Low Alloy Martensitic Steel

Martensitic microstructure in quenched and tempered 17CrNiMo6 steel with the prior austenite grain size ranging from 6 μm to 199 μm has been characterized by optical metallography （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The yield strength and the toughness of the steel with various prior austenite grain sizes were tested and correlated with microstructure characteristics. Results show that both the prior austenite grain size and the martensitic packet size in the 17CrNiMo6 steel follow a HalI-Petch relation with the yield strength. When the prior austenite grain size was refined from 199 μm to 6 μm , the yield strength increased by 235 MPa, while the Charpy U-notch impact energy at 77 K improved more than 8 times, indicating that microstructure refinement is more effective in improving the resistance to cleavage fracture than in increasing the strength. The fracture surfaces implied that the unit crack path for cleavage fracture is identified as being the packet.

Directional Solidification Assisted by Liquid Metal Cooling

An overview of the development and current status of the directional solidification process assisted by liquid metal cooling （LMC） has been presented in this paper. The driving force of the rapid development of the LMC process has been analyzed by considering the demands of （1） newer technologies that can provide higher thermal gradients for alleviated segregation in advanced alloy systems, and （2） better production yield of the large directionally solidified superalloy components. The brief history of the industrialization of the LMC process has been reviewed, followed by the discussion on the LMC parameters including selection of the cooling media, using of the dynamic baffle, and the influence of withdrawal rates and so on. The microstructure and mechanical properties of the traditional superalloys processed by LMC, as well as the new alloys particularly developed for LMC process were then described. Finally, future aspects concerning the LMC process have been summarized.

Three-Dimensional Thermo-mechanical Coupled FEM Simulation for Hot Continuous Rolling of Large-Diameter Mandrel Bar

Based on the important boundary conditions of rolling simulation including friction, heat conduction and interactionsof the workpiece and rolls, the hot continuous rolling processes of large-diameter mandrel round bar (200 mm indiameter) in 6VH-stand hot tandem mill are successfully simulated by three-dimensional coupled thermomechanicalelastoplastic finite element method (FEM). The distributions of stress, strain, temperature and the rolling force andtorque for the two-pass and four-pass continuous rolling are calculated respectively. Thus, the two and four-passroll schedules are verified, respectively. The simulation results show that it is safe to produce 200 mm round barby the two-pass (oval pass and round pass) continuous rolling on the existing equipment compared to the four-passcontinuous rolling. There are concave surfaces and increased widths occurring at the end of rolled billet due touneven deformations between the outside and inside of the workpiece as well as the free spreading close to the rollgap of the final pass.

Interface Migration between Martensite and Austenite during Quenching and Partitioning (Q&P) Process

An Fe-0.2C-1.5Si-1.67Mn steel was subjected to quenching and partitioning （Q＆P） process, and the interface migration between martensite and austenite at an elevated partitioning temperature was observed. The interface migration is excluded in constrained paraequilibrium （CPE） model. Based on ＂endpoint＂ predicted by CPE model the thermodynamic condition of interface migration is analyzed, that is, the difference in the chemical potential of iron in both ferrite （martenisite） and austenite produces the driving force of the iron atoms to migrate from one phase to the other phase. In addition, the interface migration can change the austenite fraction; as a result, the austenite fraction at partitioning temperature may be higher than that at quenching temperature through the interface migration, but this phenomenon cannot be explained by CPE model.

Deformation, Phase Transformation and Recrystallization in the Shear Bands Induced by High-Strain Rate Loading in Titanium and Its Alloys

α-titanium and its alloys with a dual-phase structure （α＋β） were deformed dynamically under strain rate of about 10^4 s^-1. The formation and microstructural evolution of the localized shear bands were characterized by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results reveal that both the strain and strain rate should be considered simultaneously as the mechanical conditions for shear band formation, and twinning is an important mode of deformation. Both experimental and calculation show that the materials within the bands underwent a superhigh strain rate （9×10^5 S^-1） deformation, which is two magnitudes of that of average strain rate required for shear band formation; the dislocations in the bands can be constricted and developed into cell structures; the phase transformation from α to α2 within the bands was observed, and the transformation products （α2） had a certain crystallographic orientation relationship with their parent; the equiaxed grains with an average size of 10 μm in diameter observed within the bands are proposed to be the results of recrystallization.

Antibacterial Mechanism of Copper-bearing Antibacterial Stainless Steel against E.Coli

A preliminary study was made on the antibacterial mechanism of copper-bearing antibacterial stainless steels against E.coli through experiments of microbiology such as EDTA （ethylenediaminetetraacetic acid） complexing, DNA smearing and AFM （atomic force microscope） observation. It was measured that the antibacterial stainless steels showed excellent antibacterial functions with antibacterial rate to E.coli over 99.99%. The antibacterial rate was weak if the bacteria solution was complexed by EDTA, indicating that the copper ions play a dominant role in the antibacterial effect of the antibacterial stainless steels. The electrophoresis experiment did not show the phenomenon of DNA smearing for E.coli after contacting antibacterial stainless steels, which meant that DNA of E.coli was not obviously damaged. It was observed by AFM that the morphology of E.coli changed a lot after contacting antibacterial stainless steels, such as cell walls being seriously changed and lots of contents in the cells being leaked.

Effect of Ultrasonic Output Power on Refining the Crystal Structures of Ingots and Its Experimental Simulation

In this study, a series of tests were conducted by using aluminum-based alloy to determine the formation of grain refining structure based on the ultrasonic vibration (UV). Furthermore, the simulation test and effect of ultrasonic output power were studied using ammonium chloride. Finally, the mechanism of grain refinement was investigated. The results show that: (1) By applying the UV to aluminum-base alloy, the grain refining rate of ingots tended to increase with the increase of the output value of UV. (2) It was confirmed that time from after the pour to the beginning of crystallization as well as cloudiness tended to decrease with increasing the ultrasonic power value of UV. Moreover, it can be seen from each cooling curve that a uniform temperature gradient existed in the melt as the power of UV increased, that made the melt strongly stirred. (3) It was also considered that the grain refining effect of ingots, which was observed from the simulation tests, resulted from nucleation action and stirring division action by applying the UV.

Effect of Aluminum and Silicon on Transformation Induced Plasticity of the TRIP Steel

With the sublattice model, equilibrium compositions of ferrite (a) and austenite (7 ) phases, as well as the volume percent of austenite (7) at 780℃ in different TRIP steels were calculated. Concentration profiles of carbon, Mn, Al and Si in the steels were also estimated under the lattice fixed frame of reference so as to understand the complex mechanical behavior of TRIP steels after different isothermal bainitic transformation treatments. The effect of Si and Mn on transformation induced plasticity (TRIP) was discussed according to thermodynamic and kinetic analyses. It is recognized that Al also induces phase transformation in the steels but its TRIP effect is not as strong as that of Si.

Preparation for Semi-Solid Aluminum Alloy Slurry under Weak Electromagnetic Stirring Conditions

The effects of pouring temperature, short electromagnetic stirring with low strength and then soaking treatment on the microstructure of AISi7Mg alloy were investigated. The results show that if AlSi7Mg alloy is poured at 630 or 650℃ and meanwhile stirred by an electromagnetic field at a low power for a short time, the pouring process can be easily controlled and most solidified primary α-Al grains become spherical and only a few of them are rosette-like. Weak electromagnetic stirring makes the temperature field more homogeneous and makes the primary α-Al grains disperse in a larger region, which leads to the spherical microstructures of primary α-Al grains. When the AISi7Mg alloy is soaked or reheated at the semisolid state, the primary α-Al grains ripen further and they become more spherical, which is favorable to the semi-solid forming of AlSi7Mg alloy.

Grain Size Control of Semisolid A356 Alloy Manufactured by Electromagnetic Stirring

To investigate the possibility of substituting the mechanical stirring system with electromagnetic stirring (EMS) system for aluminum rheo die-casting, the EMS under the different stirring cooling conditions was carried out. It was found that in the early period of solidification, the dendrite breakages led to a fine primary phase. When dendrites grew coarsely, the effect of ripening on grain size overwhelmed that of dendrite breakage. It was also found that the high cooling rate favored large nucleation rate, and led to a fine primary phase. But high cooling rate also made the growth rate of the dendrite arm, which prevented the dendrite arm from being sheared off. Therefore there were a suitable stirring time and suitable cooling rate to obtain the best rheo die-casting structure. Qualified semisolid A356 aluminum alloy was successfully manufactured with short time EMS.

Mechanical and Wear Properties of Nanostructured Surface Layer in Iron Induced by Surface Mechanical Attrition Treatment

A porosity-free and contamination-free surface layer with grain sizes ranging from nanometer to micrometer in Fe samples was obtained by surface mechanical attrition treatment (SMAT) technique. Mechanical and wear properties of the surface layer in the SMATed and annealed Fe samples were measured by means of nanoindentation and nanoscratch tests, respectively. Experimental results showed that the hardness of the surface layer in the SMATed Fe sample increased evidently due to the grain refinement. The elastic moduli of the surface layers in the SMATed and annealed Fe samples were unchanged, independent of grain size in the present grain size regime. Compared with the original Fe sample, the wear resistance enhanced and the coefficient of friction decreased in the surface layer of the SMATed Fe sample.

Oxide and Sulfide Dispersive Precipitation and Effects on Microstructure and Properties of Low Carbon Steels

Electron microscopic investigation on low carbon steel strips produced by the CSP process has been carried out. Large number of oxide dispersive precipitates have been observed in the ferrite matrix of the steel strips. Dimension of them is about 10~20 nm. Electron diffraction study showed that the structure of these precipitates consists with cubic system spinel structure. Their lattice parameter is about 0.83 nm. The results implied that they should be complex oxides of Fe, Al et al. Small sulfide particles with 100-300 nm in size have also been observed. Remarkable strengthening and grain refinement effects can be obtained by the precipitations. The oxygen and sulfur in steels could play beneficial role under certain conditions.

Energy-storage Welding Connection Characteristics of Rapid Solidification AZ91D Mg Alloy Ribbons

Energy-storage welding connection characteristics of rapidly solidified AZ91D Mg alloy ribbons with 40-70 μm thickness are investigated using a microtype energy-storage welding machine. The microstructure and performance of the connection joints are analyzed and studied. The research results indicate that energy-storage welding is able to realize the spot welding connection of AZ9ID Mg alloy ribbons. The welding nugget consists of developed α-Mg equiaxed grains with the sizes of 1.2-2.7 μm and intergranular distributed β-Mg17Al12 compounds. The thickness of bond zone is about 4 μm and the solidification microstructure is characterized by the fine equiaxed grains with the sizes of 0.8-1.2μm and grain boundary has become coarsening. The columnar crystal in HAZ also becomes slightly coarsening and the grain boundary has broadened, however, there is no obvious change in its primitive morphology and crystallographic direction. When welding energy is about 2.0 J, the welding joints with higher shear strength and smaller electrical resistivity are obtained.

Effects of Microstructure on the Tensile, Fracture Toughness and Fatigue Behaviour of Gamma Titanium Aluminides

The effects of microstructure on the deformation and fracture behaviour of two-phase TiAl alloys were investjgated under monotonic and cyclical loading conditions, over a range of temperatu res.The tensile behaviour is analyzed for deformation temperatures between RT and 950℃, Fracture resistance behaviour and toughening mechanisms at RT and 800℃ are analyzed. and the inverse relationship botween ductility and toughness is explained using the crack initiation toughness. The preliminary results of load-controlled fatigue behaviour at 800℃ are interpreted using the tensile behaviour because deformation structure and fracture modes are similar under these two loading conditions

Formation and Evolution of Non-dendritic Microstructures of Semisolid Alloys Prepared by Shearing/Cooling Roll Process

The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the microstructures of semi-solid billets transform from coarse dendrites into fine equiaxed grains as the pouring temperature of molten alloy decreases o.r roll-shoe cavity height is reduced. From the inlet to the exit of roll-shoe cavity, microstructure of semi-solid slurry near the shoe surface is in the order of coarse dendrites, degenerated dendrites or equiaxed grains, but fine equiaxed grains are near the roll surface. Microstructural evolution of semi-solid slurry prepared by SCR process is that the molten alloy nucleates and grows into dendrite firstly on the roll and shoe＇s surface. Under the shearing and stirring given by the rotating roll, the dendrites crush off and disperse into the melt. Under the shearing and stirring on semi-solid slurry with high volume fraction of solid, the dendrite arms fracture and form equiaxed grain microstructures.

Synthesis of High Purity SiC Powder for High-resistivity SiC Single Crystals Growth

High purity silicon carbide （SIC） powder was synthesized in-situ by chemical reaction between silicon and carbon powder. In order to ensure that the impurity concentration of the resulting SiC powder is suitable for high-resistivity SiC single crystal growth, the preparation technology of SiC powder is different from that of SiC ceramic. The influence of the shape and size of carbon particles on the morphology and phase composition of the obtained SiC powder were discussed. The phase composition and morphology of the products were investigated by X-ray diffraction, Raman microspectroscopy and scanning electron microscopy. The results show that the composition of resulting SiC by in-situ synthesis from Si/C mixture strongly depends on the nature of the carbon source, which corresponds to the particle size and shape, as well as the preparation temperature. In the experimental conditions, flake graphite is more suitable for the synthesis of SiC powder than activated carbon because of its relatively smaller particle size and flake shape, which make the conversion more complete. The major phase composition of the full conversion products is β-SiC, with traces of α-SiC. Glow discharge mass spectroscopy measurements indicated that SiC powder synthesized with this chemical reaction method can meet the purity demand for the growth of high-resistivity SiC single crystals.

Study on Multiple Electromagnetic Continuous Casting of Aluminum Alloy

To obtain semi-solid Al alloy billet with high quality, an investigation was carried out by imposing a multiple magnetic field from the outside of a copper mold in the continuous casting. AISi6Mg2 alloy designed for semi-solid metal （SSM） processing was continuously cast through a submerged entry nozzle under various conditions. Effects of multiple magnetic field on meniscus motion, temperature distribution and billet quality were examined. The experimental results showed that meniscus disturbance caused by electromagnetic stirring could be controlled effectively and the surface quality of semi-solid AI alloy billet was improved greatly, and an uniformly fine, globular microstructure across the transverse section of the billet was achieved by optimizing the distribution of multiple magnetic field.

Current Status in Layered Ternary Carbide Ti_3SiC_2,a Review

This article provides a review of current research activities that concentrate on Ti3SiC2. We begin with an overview of the crystal and electronic structures, which are the basis to understand this material. Followings are the synthetic strategies that have been exploited to achieve, and the formation mechanism of Ti3SiC2. Then we devote much attentions to the mechanical properties and oxidation/hot corrosion behaviors of Ti3SiC2 as well as some advances achieved recently. At the end of this paper, we elaborate on some new discoveries in the Ti3SiC2 system, and also give a brief discussion focused on the ＂microstructure -property＂ relationship.