煤矿大倾角综采工作面仰斜回采技术

本文介绍大倾角综采工作面仰采的重要技术,通过具体的安全措施,以满足仰斜回采技术的要求。

Monitoring coal fires in Datong coalfield using multi-source remote sensing data

Numerous coal fires burn underneath the Datong coalfield because of indiscriminate mining.Landsat TM/ETM,unmanned aerial vehicle（UAV）,and infrared thermal imager were employed to monitor underground coal fires in the Majiliang mining area.The thermal field distributions of this area in 2000,2002,2006,2007,and 2009 were obtained using Landsat TM/ETM.The changes in the distribution were then analyzed to approximate the locations of the coal fires.Through UAV imagery employed at a very high resolution（0.2 m）,the texture information,linear features,and brightness of the ground fissures in the coal fire area were determined.All these data were combined to build a knowledge model of determining fissures and were used to support underground coal fire detection.An infrared thermal imager was used to map the thermal field distribution of areas where coal fire is serious.Results were analyzed to identify the hot spot trend and the depth of the burning point.

Behaviors of vanadium and chromium in coal-based direct reduction of high-chromium vanadium-bearing titanomagnetite concentrates followed by magnetic separation

The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The effects of molar ratio of C to Fe n(C)/n(Fe) and temperature on the behaviors of vanadium and chromium during direct reduction and magnetic separation were investigated. The reduced samples were characterized by X-ray diffraction(XRD), scanning election microscopy(SEM) and energy dispersive spectrometry(EDS) techniques. Experimental results indicate that the recoveries of vanadium and chromium rapidly increase from 10.0% and 9.6% to 45.3% and 74.3%, respectively, as the n(C)/n(Fe) increases from 0.8 to 1.4. At n(C)/n(Fe) of 0.8, the recoveries of vanadium and chromium are always lower than 10.0% in the whole temperature range of 1100-1250 °C. However, at n(C)/n(Fe) of 1.2, the recoveries of vanadium and chromium considerably increase from 17.8% and 33.8% to 42.4% and 76.0%, respectively, as the temperature increases from 1100 °C to 1250 °C. At n(C)/n(Fe) lower than 0.8, most of the FeO·V2O3 and FeO·Cr2O3 are not reduced to carbides because of the lack of carbonaceous reductants, and the temperature has little effect on the reduction behaviors of FeO·V2O3 and FeO·Cr2O3, resulting in very low recoveries of vanadium and chromium during magnetic separation. However, at higher n(C)/n(Fe), the reduction rates of FeO·V2O3 and FeO·Cr2O3 increase significatly because of the excess amount of carbonaceous reductants. Moreover, higher temperatures largely induce the reduction of FeO·V2O3 and FeO·Cr2O3 to carbides. The newly formed carbides are then dissolved in the γ(FCC) phase, and recovered accompanied with the metallic iron during magnetic separation.

Soil Environmental Quality Evaluation for Wasteland of Coalmine Tailing Polluted by Heavy Metals in Mingshan of Guangdong

ln order to appraise scientifical y the heavy metal contamination in waste-land of coalmine tailing in Mingshan of Guangdong, the 5 soil samples in wasteland of coalmine tailing were col ected in November 2010 to March 2011. The 7 heavy metals content in the contaminated soil was measured by atomic absorption spec-trophotometry. The results showed the pH of the wasteland soil ranged from 2.87 to 6.16, and the soil was relatively infertile. The soil was mainly pol uted by Cd and Mn. The Cd content in wasteland soil ranged from 0.759 mg/kg to 3.109 mg/kg with an average content of 2.052 mg/kg, which was much higher than the standard content. The Mn content ranged from 387.057 to 488.660 mg/kg with an average content of 421.215 mg/kg, which was much higher than the standard content. The Nemerow integrated pol ution indexes showed the sample 1, sample 4 and sample 5 were of heavy pol ution, and sample 2 and sample 3 were of moderate pol ution.

Vanadium recovery from stone coal through roasting and flotation

A new process for vanadium recovery from stone coal by roasting-flotation was investigated based on the mineralogy. The process comprised four key steps： decarburization, preferential grinding, desliming and flotation. In the decarburization stage, roasting at 550 ℃ effectively avoided the negative effect of the carbonaceous materials in raw ore and generation of free CaO from calcite decomposition during roasting. Through preferential grinding, the high acid-consuming minerals were enriched in the middle fractions, while mica was enriched in the fine and coarse fractions. Through flotation, the final concentrate can be obtained with V2O5 grade of 1.07% and recovery of 83.30%. Moreover, the vanadium leaching rate of the final concentrate increased 13.53% compared to that of the feed. The results reveal that the decarburization by roasting at 550 ℃ is feasible and has little negative impact on mica flotation, and vanadium recovery from stone coal is conducive to reducing handling quantity, acid consumption and production cost.

HIERARCHICAL ITERATIVE GA FOR OPTIMIZATION OF THE PLAN IN COAL MINE CONSTRUCTION

In coal mine construction,to make the optimal plan of complete sets of equipment needs to set up a mixed integer nonlinear programming model,which has many variables and more complicated parameters to set.The problem could hardly be solved using general methods.In this paper a new genetic approach—the hierarchical iterative genetic algorithm (HIGA) was designed to solve it and a satisfactory solution was obtained.

Ordovician limestone aquosity prediction using nonlinear seismic attributes:Case from the Xutuan coal mine

Ordovician limestone water is coal mines. In this paper, we analyze the the main source of water inrush in North China characteristic of three kinds of nonlinear seismic attributes, such as the largest lyapunov exponent,fractal dimension and entropy and introduce their calculation methods. Taking the 81st and 82nd coal districts in the Xutuan coal mine as examples, we extract the three seismic attributes based on the 3D prestack migration seismic data of this area, which can display the Ordovician limestone fracture distribution in the mine. We comprehensively analyzed the three nonlinear seismic attributes and compared the results with transient electromagnetic exploration results and determined the possible Ordovician limestone aquosity distribution. This demonstrated that the nonlinear seismic attributes technology is an effective approach to predict the aquosity of Ordovician limestone.

Prevention and forecasting of rock burst hazards in coal mines

Rock bursts signify extreme behavior in coal mine strata and severely threaten the safety of the lives of miners, as well as the effectiveness and productivity of miners. In our study, an elastic-plastic-brittle model for the deformation and failure of coal/rock was established through theoretical analyses, laboratory experiments and field testing, simulation and other means, which perfectly predict sudden and delayed rock bursts. Based on electromagnetic emission (EME), acoustic emission (AE) and microseism (MS) effects in the process from deformation until impact rupture of coal-rock combination samples, a multi-parameter identification of premonitory technology was formed, largely depending on these three forms of emission. Thus a system of classification for forecasting rock bursts in space and time was established. We have presented the intensity weakening theory for rock bursts and a strong-soft-strong (3S) structural model for controlling the impact on rock surrounding roadways, with the objective of laying a theoretical foundation and establishing references for parameters for the weakening control of rock bursts. For the purpose of prevention, key technical parameters of directional hydraulic fracturing are revealed. Based on these results, as well as those from deep-hole controlled blasting in coal seams and rock, integrated control techniques were established and anti-impact hydraulic props, suitable for roadways subject to hazards from rockbursts have also been developed. These technologies have been widely used in most coal mines in China, subject to these hazards and have achieved remarkable economic and social benefits.

Similarity criteria and coal-like material in coal and gas outburst physical simulation

Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.

Modelling spontaneous combustion liability of carbonaceous materials

This paper presents predictive models to determine spontaneous combustion liability of carbonaceous materials （coals and coal-shales） using statistical analysis. The intrinsic properties and spontaneous combustion liability index were determined by testing 14 coals and 14 coal-shales from Witbank coalfields, South Africa. The relationship between these intrinsic properties （obtained from proximate, ultimate and petrographic analysis） and spontaneous combustion liability indices （the Wits-Ehac Index and Wits-CT Index） were established. The influence of the intrinsic properties of coal-shales in relation to coal properties affecting spontaneous combustion has been established using a statistical method. The linear regression analysis indicates better linear relationships between some of the selected intrinsic properties and spontaneous combustion liability index and thus, identifies the major intrinsic factors affecting their liability toward spontaneous combustion. It was found that a definite positive or negative correlation coefficient exists between the intrinsic factors and spontaneous combustion liability. A set of models to predict the spontaneous combustion liability was derived. The best significant correlation along with the most appropriate model as indicated by R-squared values, the coefficient of corre- lations and standard error was used to predict the incident of spontaneous combustion.

Forecasting water disaster for a coal mine under the Xiaolangdi reservoir

Xin’an coal mine, Henan Province, faces the risk of water inrush because 40% of the area of the coal mine is under the surface water of the Xiaolangdi reservoir. To forecast water disaster, an effective aquifuge and a limit of water infiltration were determined by rock-phase analysis and long term observations of surface water and groundwater. By field monitoring, as well as physical and numerical simulation experiments, we obtained data reflecting different heights of a water flow fractured zone (WFFZ) under different mining conditions, derived a formula to calculate this height and built a forecasting model with the aid of GIS. On the basis of these activities, the coal mine area was classified into three sub-areas with different potential of water inrush. In the end, our research results have been applied in and verified by industrial mining experiments at three working faces and we were able to present a successful example of coal mining under a large reservoir.

Waste-filling in fully-mechanized coal mining and its application

A fully-mechanized coal mining (FMCM) technology capable of filling up the goaf with wastes (including solid wastes) is described. Industrial tests have proved that by using this technology not only can waste be re-used but also coal resources can be exploited with a higher recovery rate without removing buildings located over the working faces. Two special devices, a hydraulic support and a scraper conveyor, run side-by-side on the same working face to simultaneously realize mining and filling. These are described in detail. The tests allow analysis of rock pressure and ground subsidence when backfilling techniques are employed. These values are compared to those from mining without using backfilling techniques, under the same geological conditions. The concept of equivalent mining height is proposed based on theoretical analysis of rock pressure and ground subsidence. The upper limits of the rock pressure and ground subsidence can be estimated in backfilling mining using this concept along with traditional engineering formulae.

Coal bursts in the deep longwall mines of the United States

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past 2 years three US coal miners were killed in two coal bursts, following a 6-year period during which there were zero burst fatalities. This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields which have struggled with bursts for decades. The Utah experience displays many of the ＂classic＂ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley （NFV） also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders, or other outby locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper provides a detailed case history to illustrate the experience in each of these coalfields. The paper closes with a brief discussion of how US longwalls have managed the burst risk.

Ground stability of underground gateroad with 1 km burial depth： A case study from Xingdong coal mine, China

This paper presents an integrated investigation of the ground stability of a deep gateroad with a 1 km burial depth based on a field test, case studies, and numerical modelling. In situ stress measurements and mechanical properties tests were first conducted in the test site. Then, the deformation behavior, stress and yield zone distributions, as well as the bolts load of the gateroad, were simulated using FLAC3D software. The model results demonstrated that the soft rock properties and high in situ stress were the main factors for the deep gateroad instability, and the shear slip failure induced by the high stress was the primary failure model for the deep rock mass. In addition, the unsuitable support patterns, especially the relatively short bolts/cables with low pre-tensions, the lack of high-strengthen secondary supports and the unsupported floor strata, also contributed to the gateroad instability. Subsequently, a new combined supporting strategy, incorporating longer bolts/cables, yielding ring supports, and grouting measures, was proposed for the deep gateroad, and its validity was verified via field monitoring. All these could be a reference for understanding the failure mechanism of the gateroad with 1 km burial depth.

Sensing for advancing mining automation capability:A review of underground automation technology development

This paper highlights the role of automation technologies for improving the safety, productivity, and environmental sustainability of underground coal mining processes. This is accomplished by reviewing the impact that the introduction of automation technology has made through the longwall shearer automation research program of Longwall Automation Steering Committee(LASC). This result has been achieved through close integration of sensing, processing, and control technologies into the longwall mining process. Key to the success of the automation solution has been the development of new sensing methods to accurately measure the location of longwall equipment and the spatial configuration of coal seam geology. The relevance of system interoperability and open communications standards for facilitating effective automation is also discussed. Importantly, the insights gained through the longwall automation development process are now leading to new technology transfer activity to benefit other underground mining processes.

Study of a Comprehensive Assessment Method for Coal Mine Safety Based on a Hierarchical Grey Analysis

Coal mine safety is a complex system, which is controlled by a number of interrelated factors and is difficult to estimate. This paper proposes an index system of safety assessment based on correlated factors involved in coal mining and a comprehensive evaluation model that combines the advantages of the AHP and a grey clustering method to guarantee the accuracy and objectivity of weight coefficients. First, we confirmed the weight of every index using the AHP, then did a general safety assessment by means of a grey clustering method. This model analyses the status of mining safety both qualitatively and quantitatively. It keeps management and technical groups informed of the situation of the coal production line in real time, which aids in making correct decisions based on practical safety issues. A case study in the application of the model is presented. The results show that the method is applicable and realistic with regard to the core of a coal mine's safety management. Consequently, the safe production of a mine and the awareness of advanced safe production management is accelerated.

Risk evaluation of rock burst through theory of static and dynamic stresses superposition

Rock burst is one of the most catastrophic dynamic hazards in coal mining. A static and dynamic stresses superposition-based(SDSS-based) risk evaluation method of rock burst was proposed to pre-evaluate rock burst risk. Theoretical basis of this method is the stress criterion incurring rock burst and rock burst risk is evaluated according to the closeness degree of the total stress(due to the superposition of static stress in the coal and dynamic stress induced by tremors) with the critical stress. In addition, risk evaluation criterion of rock burst was established by defining the "Satisfaction Degree" of static stress. Furthermore,the method was used to pre-evaluate rock burst risk degree and prejudge endangered area of an insular longwall face in Nanshan Coal Mine in China. Results show that rock burst risk is moderate at advance extent of 97 m, strong at advance extent of 97-131 m,and extremely strong(i.e. inevitable to occur) when advance extent exceeds 131 m(mining is prohibited in this case). The section of two gateways whose floor abuts 15-3 coal seam is a susceptible area prone to rock burst. Evaluation results were further compared with rock bursts and tremors detected by microseismic monitoring. Comparison results indicate that evaluation results are consistent with microseismic monitoring, which proves the method's feasibility.

Study on the genesis of karstic collapse column and characteristics of high resolution seismic data in one coal field

On the standpoint of the disaster prevention from water inrush,discussed the genesis and geologic condition of karstic collapse column in one coal field,analyzed the geophysical characteristics of karstic collapse column by using high resolution 3D seismic data.It shows the effective result of the technology of high resolution 3D seismic pros- pecting in the exploration of the karstic collapse column,and presents some prediction methods and prevention measures.

Experimental Research on Desulfurization of Fine Coal Using an Enhanced Centrifugal Gravity Separator

A desulphurization experimental study under the effects of compounding physical force fields has been described for 〈 0.5 mm fine particles of high sulfur coal. A statistical test using the Box-Behnken Design of experiments was conducted to evaluate the effects of individual operating variables and their interactions on desulfurization of fine coal using an enhanced centrifugal gravity separator. A model describing the relation between desulphurization efficiency of pyrite sulfur and different operating variables has been designed. The interactions between different factors on the pyrite sulfur desulphurization efficiency have been analysed. The optimal test conditions for desulfarization are extracted from the Design-Expert 6.0 software. Finally, the pointed out. advantage of centrifugal gravity separation for fine coal is pointed out.

Application of HEMS cooling technology in deep mine heat hazard control

This paper mainly deals with the present situation, characteristics, and countermeasures of cooling in deep mines.Given existing problems in coal mines, a HEMS cooling technology is proposed and has been successfully applied in some mines.Because of long-term exploitation, shallow buried coal seams have become exhausted and most coal mines have had to exploit deep buried coal seams.With the increase in mining depth, the temperature of the surrounding rock also increases, resulting in ever increasing risks of heat hazard during mining operations.At present, coal mines in China can be divided into three groups, i.e., normal temperature mines, middle-to-high temperature mines and high temperature mines, based on our investigation into high temperature coal mines in four provinces and on in-situ studies of several typical mines.The principle of HEMS is to extract cold energy from mine water inrush.Based on the characteristics of strata temperature field and on differences in the amounts of mine water inrush in the Xuzhou mining area, we proposed three models for controlling heat hazard in deep mines:1) the Jiahe model with a moderate source of cold energy;2) the Sanhejian model with a shortage of source of cold energy and a geothermal anomaly and 3) the Zhangshuanglou model with plenty of source of cold energy.The cooling process of HEMS applied in deep coal mine are as follows:1) extract cold energy from mine water inrush to cool working faces;2) use the heat extracted by HEMS to supply heat to buildings and bath water to replace the use of a boiler, a useful energy saving and environmental protection measure.HEMS has been applied in the Jiahe and Sanhejian coal mines in Xuzhou, which enabled the temperature and humidity at the working faces to be well controlled.