Analysis on the Composition and Structure of Branches of Two Kinds of Tree Shapes in Korla Fragrant Pear

ObjectiveThe thesis aims at investigating the distribution and structural characteristics of various branches in canopy of Korla fragrant pear. MethodStatistic work and analysis were conducted on the numbers and distribution characteristics of various branches in each cubic lattice by using the canopy cellular method. ResultThe results showed that： The total number of scaffold branches of evacuation layered tree shape was 97, which mainly distributed in the lower layer and middle part of the canopy; the total number of scaffold branches of open-center tree shape was 94, which mainly distributed in the lower layer and middle part of the canopy. The total number of annual branches of evacuation layered tree shape was 3 920, which mainly distributed in the middle layer and outer part of the canopy; and the total number of annual branches of the open-center tree shape was 3 183, which mainly distributed in middle layer and outer part of the canopy. The total number of perennial branches of evacuation layered tree shape was 2 184, which mainly distributed in lower layer and outer part of the canopy; the total number of perennial branches of open-center tree shape was 1 444, which mainly distributed in middle layer and outer part of the canopy. ConclusionThe total number and the distribution positions of scaffold branches in the canopy of each tree shape were basically the same. The total numbers of annual branches of the two kinds of tree shapes were different, but the distribution positions were basically the same. The total numbers and the distribution positions of perennial branches in the canopy of the two kinds of tree shapes were different.

A Ventral Diverterless High Offset S-shaped Inlet at Transonic Speeds

An investigation on the ventral diverterless high offset S-shaped inlet is carried out at Mach numbers from 0.600 to 1.534, angles of attack from -4° to 9.4°, and yaw angles from 0° to 8°. Results indicate： （1） a large region of low total pressure exists at the lower part of the inlet exit caused by the counter-rotating vortices in the S-shaped duct; （2） the performances of the inlet at Mach number 1.000 reach almost the highest, so the propulsion system could work efficiently in terms of aerodynamics; （3） the total pressure recovery increases slowly at first and then remains unvaried as the Mach number rises from 0.6 to 1.0, however, it does in an opposite manner in the conventional diverter-equipped S-shaped inlet; （4） the performances of the inlet are generally insensitive to angles of attack from -4° to 9.4° and yaw angles from 0° to 8° at Mach number 0.850, and angles of attack from -2° to 6° and yaw angles from 0° to 5° at Mach number 1.534.

基于哨兵函数和S变换的风力机叶片材料损伤特性研究

利用声发射检测技术研究玻璃纤维增强环氧树脂复合材料的损伤特性,在此过程中,采用哨兵函数来表征该材料的损伤程度,并通过S变换和模糊C均值(FCM)聚类来分析声发射信号,从而获得材料的损伤特征。三点弯曲实验结束后对试件断口进行扫描电子显微镜(SEM)拍照来验证,可得:通过对SEM照片的分析得到基体开裂、纤维脱粘、分层破坏、纤维断裂4种损伤模式;对整个声发射事件进行哨兵函数分析,观察到试件在弯曲过程中哨兵函数曲线呈明显下降趋势;对依据哨兵函数划分的不同阶段的信号进行VMD降噪处理,然后采用S变换进行时频分析得到不同损伤的特征频率,最后采用FCM聚类进行验证。结果表明:哨兵函数值的突变可作为材料断裂的预警信号,材料损伤类型的识别可依据S变换的频率分布结果进行确定。

一种基于随机求反的S盒抗DPA攻击安全结构

DPA攻击(差分功耗攻击)作为一种重要的侧信道攻击方法,因其成功率较高而成为加密算法面临的主要威胁之一。S盒是分组加密算法(高级加密标准(AES)、国产商业密码(SM4)等)中唯一的非线性运算,很大程度上决定了相关加密算法的安全性。S盒的实现主要分为:查表法、组合逻辑和复合域方法。复合域方法因将S盒中的GF(28)域上的求逆运算分解到低阶域上而使其硬件实现具有高性能、低面积等优势。该文提出了一种基于随机求反的复合域S盒抗DPA攻击安全结构,并据此设计了两类抗DPA攻击的AES安全结构:一种是基于随机取反的AES安全结构(RC-AES安全结构),另一种是基于随机取反与一阶掩码结合的AES安全结构(RC-M-AES安全结构)。实验证明,相较于已知文献中基于掩码保护的AES,该文提出的RC-AES结构只需增加微小的面积开销就能有效抵抗DPA攻击,展现出显著的面积优势。同时,RC-M-AES安全结构能在微小面积开销下,构建出比单独掩码方案更安全的密码芯片结构。此外,提出的S盒安全结构不仅适用于AES,也适用于任何以替换函数作为唯一非线性运算的加密算法,具有较好的通用性。

Influence of Thermal Treatments on In-depth Compositional Uniformity of Culn（S,Se）2 Thin Films

CuIn（S,Se）2 thin films were prepared by thermal crystallization of co-sputtered Cu-In alloy precursors in S/Se atmosphere. In-depth compositional uniformity is an important prereq- uisite for obtaining device-quality CuIn（S,Se）2 absorber thin films. In order to figure out the influence of heat treatments on in-depth composition uniformity of CuIn（S,Se）2 thin films, two kinds of reaction temperature profiles were investigated. One process is ＂one step profile＂, referring to formation of CuIn（S,Se）2 thin films just at elevated temperature （e.g. 500 ℃）. The other is ＂two step profile＂, which allows for slow diffusion of S and Se elements into the alloy precursors at a low temperature before the formation and re-crystallization of CuIn（S,Se）2 thin films at higher temperature （e.g. first 250 ℃ then 500 ℃）. X-ray diffrac- tion studies reveal that there is a discrepancy in the shape of （112） peak. Samples annealed with ＂one step profile＂ have splits on （112） peaks, while samples annealed with ＂two step profile＂ have relatively symmetrical （112） peaks. Grazing incident X-ray diffraction and en- ergy dispersive spectrum measurements of samples successively etched in bromine methanol show that CuIn（S,Se）2 thin films have better in-depth composition uniformity after ＂two step profile＂ annealing. The reaction mechanism during the two thermal processing was also investigated by X-ray diffraction and Raman spectra.

Nonlinear dynamic characteristics and optimal control of a giant magnetostrictive film-shaped memory alloy composite plate subjected to in-plane stochastic excitation

The nonlinear dynamic characteristics and optimal control of a giant magnetostrictive film （GMF）-shaped memory alloy （SMA） composite plate subjected to in-plane stochastic excitation are studied. GMF is prepared based on an SMA plate, and combined into a GMF-SMA composite plate. The Van der Pol item is improved to explain the hysteretic phenomena of GMF and SMA, and the nonlinear dynamics model of a GMF-SMA composite cantilever plate subjected to in-plane stochastic excitation is developed. The stochastic stability of the system is analyzed, and the steady-state probability density function of the dynamic response of the system is obtained. The condition of stochastic Hopf bifurcation is discussed, the reliability function of the system is provided, and then the probability density of the first-passage time is given. Finally, the stochastic optimal control strategy is proposed by the stochastic dynamic programming method. Numerical simulation shows that the stability of the trivial solution varies with bifurcation parameters, and stochastic Hopf bifurcation appears in the process; the system＇s reliability is improved through stochastic optimal control, and the first- passage time is delayed. A GMF-SMA composite plate combines the advantages of GMF and SMA, and can reduce vibration through passive control and active control effectively. The results are helpful for the engineering applications of GMF-SMA composite plates.

Soil fungistasis and its relations to soil microbial composition and diversity:A case study of a series of soils with different fungistasis

Fungistasis is one of the important approaches to control soil-borne plant pathogens.Some hypotheses about the mechanisms for soil fungistasis had been established,which mainly focused on the soil bacterial community composition,structure,diversity as well as function.In this study,the bacterial community composition and diversity of a series of soils treated by autoclaving,which coming from the same original soil sample and showing gradient fungistasis to the target soil-borne pathogen fungi Fusarium grami...

Weighted composition operators from F(p,q,s) spaces to Bers-type spaces in the unit ball

This paper deals with the boundedness and compactness of the weighted composition operators from the F（p, q, s） spaces, including Hardy space, Bergman space, Qp space, BMOA space, Besov space and α-Bloch space, to Bers-type spaces Hv^∞（ or little Bers-type spaces Hv,o∞ ）, where v is normal.

售货机升降系统S型速度控制策略

在传统三闭环控制方式下,售货机升降接货系统易因启停过程中加速度突变产生冲击,导致系统运行不平稳。针对这一问题,文中对传统升降系统加减速控制策略进行改进,加入前馈和微分负反馈,提出一种S型速度曲线控制算法。根据路径规划判别条件将S型速度曲线分为七段式、六段式和四段式3种,并给出各路径约束条件下的参数求解方法和具体执行流程。将该算法运用到升降控制系统中进行仿真和实际工况测试,实验结果表明,与传统三闭环控制相比,文中所提控制策略可以提高售货机升降系统运行的平稳性,减小冲击,使速度曲线更加柔和,并能够保持较好的跟踪性能。

ON THE COMPOSITION UNIFORMITY AND SHAPE COEFFICIENT OF MOLTEN POOL BY LASER ALLOYING

The effect of the laser processing parameters on the composition uniformity and shape coefficient of fusion zone with laser surface alloyed Cr plated on medium carbon low alloy steel has been studied.It was found that the composition uniformity depends on the shape coefficient of fusion zone,and the later is a function of both power density and interaction time.If the power density is fixed to a certain value,the shape coefficient is directly,propor- tional to the interaction time.A completely,uniform molten pool can be obtained,when the shape coefficient is between 1.6 and 3.0.

Analysis of cultivable aerobic bacterial community composition and screening for facultative sulfate-reducing bacteria in marine corrosive steel

Anaerobic, aerobic, and facultative bacteria are all present in corrosive environments. However, as previous studies to address corrosion in the marine environment have largely focused on anaerobic bacteria, limited attention has been paid to the composition and function of aerobic and facultative bacteria in this process. For analysis in this study, ten samples were collected from rust layers on steel plates that had been immersed in seawater for diff erent periods (i.e., six months and eight years) at Sanya and Xiamen, China. The cultivable aerobic bacterial community structure as well as the number of sulfate-reducing bacteria (SRB) were analyzed in both cases, while the proportion of facultative SRB among the isolated aerobic bacteria in each sample was also evaluated using a novel approach. Bacterial abundance results show that the proportions are related to sea location and immersion time;abundances of culturable aerobic bacteria (CAB) and SRB from Sanya were greater in most corrosion samples than those from Xiamen, and abundances of both bacterial groups were greater in samples immersed for six months than for eight years. A total of 213 isolates were obtained from all samples in terms of CAB community composition, and a phylogenetic analysis revealed that the taxa comprised four phyla and 31 genera. Bacterial species composition is related to marine location;the results show that Firmicutes and Proteobacteria were the dominant phyla, accounting for 98.13% of the total, while Bacillus and Vibrio were the dominant genera, accounting for 53.06% of the total. An additional sixfacultative SRB strains were also screened from the isolates obtained and were found to encompass the genus Vibrio (four strains), Staphylococcus (one strain), and Photobacterium (one strain). It is noteworthy that mentions of Photobacterium species have so far been absent from the literature, both in terms of its membership of the SRB group and its relationship to corrosion.

Gallbladder bile composition in patients with Crohn's disease

AIM： To further elucidate the pathogenesis and mechanisms of the high risk of gallstone formation in Crohn＇s disease. METHODS： Gallbladder bile was obtained from patients with Crohn＇s disease who were admitted for elective surgery （27 with ileal/ileocolonic disease and 7 with Crohn＇s colitis）. Fourteen gallstone patients served as controls. Duodenal bile was obtained from ten healthy subjects before and after the treatment with ursodeoxycholic acid. Bile was analyzed for biliary lipids, bile acids, bilirubin, crystals, and crystal detection time （CDT）. Cholesterol saturation index was calculated. RESULTS： The biliary concentration of bilirubin was about 50% higher in patients with Crohn＇s disease than in patients with cholesterol gallstones. Ten of the patients with Crohn＇s disease involving ileum and three of those with Crohn＇s colitis had cholesterol saturated bile. Four patients with ileal disease and one of those with colonic disease displayed cholesterol crystals in their bile. About 1/3 of the patients with Crohn＇s disease had a short CDT. Treatment of healthy subjects with ursodeoxycholic acid did not increase the concentration of bilirubin in duodenal bile. Several patients with Crohn＇s disease, with or without ileal resection/disease had gallbladder bile supersaturated with cholesterol and short CDT and contained cholesterol crystals. The biliary concentration of bilirubin was also increased in patients with Crohn＇s colitis probably not due to bile acid malabsorption. CONCLUSION： Several factors may be of importance for the high risk of developing gallstones of both cholesterol and pigment types in patients with Crohn＇s disease.The skillful technical assistance of Ms Lisbet Benthin and Ms Ingela Arvidsson is acknowledged.

基于S形速度曲线的键合头运动控制系统研究与分析

根据用户工艺需求,针对全自动芯片键合设备的运动控制模块以及键合头子模块开展需求分析,结合典型试验,设计出基于S形速度曲线的键合头运动控制系统,根据S形速度曲线重新规划了键合头的运动轨迹,使其对芯片键合周期缩短的同时也保证了键合精度。

Effect of Lycopus lucidus Turcz.supplementation on gut microflora and short chain fatty acid composition in Crj:CD-1 mice

We investigated the diversity and composition of microflora in feces of Lycopus lucidus Turcz.-fed mice.In addition,we evaluated the production of major cytokines(Interleukin-6 and-10)which are related to inflammation and fatty acid composition of several tissues.16S ribosomal DNA sequencing-based microbiome taxonomic profiling analysis was performed utilizing the EzBioCloud data base.Male mice fed on L.lucidus showed a significantly reduced number of lactic acid bacteria and coliform in the feces compared with the control group(p<0.05).16S rDNA sequencing analysis of fecal samples showed that L.lucidus supplementation decreased the community of harmful microflora(Enterobacteriaceae including Escherichia coli and Bacteroides sp.)in feces compared with the control group(p<0.05).There were no significant differences in mRNA expression of cytokine IL-6 and IL-10 between the control and L.lucidus fed groups.The fecal fatty acid composition in the L.lucidus group had percentages of 4:0,6:0,8:0 and 10:0 in the intestine but those short chain fatty acids were not detected in the control group.Our results showed that L.lucidus supplementation influenced gut environment by decreasing harmful microflora and increased the percentages of several short fatty acids.

Numerical Investigation of Electrohydrodynamic (EHD) Flow Control in an S-Shaped Duct

An electrohydrodynamic （EHD） method, which is based on glow discharge plasma, is presented for flow control in an S-shaped duct. The research subject is an expanding channel with a constant width and a rectangular cross section. An equivalent divergence angle and basic function are introduced to build the three-dimensional model. Subsequently, the plasma physical models are simplified as the effects of electrical body force and work （done by the force） on the fluid near the wall. With the aid of FLUENT software, the source terms of momentum and energy are added to the Navier-Stokes equation. Finally, the original performance of three models （A, B and C） is studied, in which model A demonstrates better performance. Then EHD control based on model A is discussed. The results show that the EHD method is an effective way of reducing flow loss and improving uniformity at the duct exit. The innovation in this study is the assessment of the EHD control effect on the flow in an S-shaped duct. Both the parametric modeling of the S-shaped duct and the simplified models of plasma provide valuable information for future research on aircraft inlet ducts.

液压成形对液体火箭发动机多层增强S型波纹管结构疲劳寿命的影响

完善液体火箭发动机燃气摇摆装置中增强S型波纹管组件的疲劳寿命评估方法,提高其疲劳寿命预测精度,是发展可重复使用液体火箭发动机的重要课题之一。针对多层增强S型波纹管,为了计算其液压成形后的实际寿命数据,了解成形工艺对其疲劳寿命的影响,提出一种充分考虑成形制备过程对结构不同区域几何构型和材料力学性能造成差异化影响后的波纹管疲劳寿命分析方法。该方法基于成形仿真和材料拉伸试验结果,构建实际波纹管有限元模型并进行三维仿真分析,得到其在高内压和不同摆动工况下结构危险点的循环载荷信息,并根据波纹管结构的低周疲劳失效特点采用子午向应力应变数据,以及经过平均应力应变修正的Manson-Coffin(M-C)公式对波纹管的循环寿命进行估算和对比分析。结果表明:波纹管疲劳寿命薄弱点位置和大小均与循环摆角有关;在预测计算中考虑液压成形作用影响更接近实际场景,所得结构疲劳寿命大小和所在区域均与理论模型值存在差异,在结构设计、优化和健康监测中不应忽视其影响。

Incorporating S-shaped testing-effort functions into NHPP software reliability model with imperfect debugging

Testing-effort（TE） and imperfect debugging（ID） in the reliability modeling process may further improve the fitting and prediction results of software reliability growth models（SRGMs）. For describing the S-shaped varying trend of TE increasing rate more accurately, first, two S-shaped testing-effort functions（TEFs）, i.e.,delayed S-shaped TEF（DS-TEF） and inflected S-shaped TEF（IS-TEF）, are proposed. Then these two TEFs are incorporated into various types（exponential-type, delayed S-shaped and inflected S-shaped） of non-homogeneous Poisson process（NHPP）SRGMs with two forms of ID respectively for obtaining a series of new NHPP SRGMs which consider S-shaped TEFs as well as ID. Finally these new SRGMs and several comparison NHPP SRGMs are applied into four real failure data-sets respectively for investigating the fitting and prediction power of these new SRGMs.The experimental results show that：（i） the proposed IS-TEF is more suitable and flexible for describing the consumption of TE than the previous TEFs;（ii） incorporating TEFs into the inflected S-shaped NHPP SRGM may be more effective and appropriate compared with the exponential-type and the delayed S-shaped NHPP SRGMs;（iii） the inflected S-shaped NHPP SRGM considering both IS-TEF and ID yields the most accurate fitting and prediction results than the other comparison NHPP SRGMs.

Interfacial stress transfer behavior in a specially-shaped fiber/matrix pullout test

Specially designed fibers are widely used in engineering practice because the specially-designed shape can help to improve the bonding strength of the fiber and the interface. Studied in this paper is the interfacial shear stress transfer behavior on both sides of the specially designed fiber when it is being pulled out; in which automatic analysis of three-dimensional photoelasticity is employed and the finite element method is adopted. The results show that the stress transfer occurs mainly in the region near the fiber＇s embedded end where the stress reaches its critical point, leading to debonding of the interface. Before debonding, as the pullout loading increases, the peak value of shear stress transfers along the fiber from the embedded end to the interior of the matrix, and then stops at the hooked part of the fiber because of its impediment. When the interface begins to debond as the load increases, the shear stress can be transferred to the hooked part.

WEIGHTED COMPOSITION OPERATORS ON WEIGHTED DIRICHLET SPACES

We characterize the boundedness and compactness of weighted composition operators on weighted Dirichlet spaces in terms of Nevanlinna counting functions and Caxleson measure.

Influences of Composition and Annealing on the Martensitic Transformation in Ni-Fe-Ga Alloys

A series of Ni-Fe-Ga alloys near the prototype Heusler composition （X2YZ） were prepared through arc-melting suction-casting method. The dependences of the transformation behavior on the alloy composition and annealing treatment were studied in detail by an optical microscope, X-ray diffraction, and differential scanning calorimeters methods. The experimental results show that the martensitic transformation temperatures increase almost linearly with increasing Ni content in all the NiFeGa alloys. Annealing the Ni55.5Fe18Ga26.5 alloy at 100-500 ℃ for 3 h and at 300 ℃ for 1-10 h shifts the martensitic transformation start temperature by almost 20 ℃ to high temperature. The variations in the martensitic transformation temperatures in these alloys are discussed in terms of structural differences resulting from alloy composition and annealing treatment.