定压外边界的双孔介质复合储层中井底压力分析

针对外边界定压的双孔介质复合储层物理模型,用数学方法研究了两种内边界条件(是否考虑井筒储存和表皮 效应)下的变(常)流率问题的无因次井底压力的Laplace空间解,在深入剖析了解的结构和相互联系的基础上,找出了它 与常见的复合、双孔、均质储层井底压力间的相互关系,并简要地引导了相应的应用.此项研究,无疑是对试井分析 理论的一种完善,对相应的试井分析软件的研制具有深远的应用价值,对油藏工程中的数值模拟方法也具有指导意义.

Flow behavior and microstructure of ZK60 magnesium alloy compressed at high strain rate

Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.

Effect of Zr and Sc on mechanical properties and electrical conductivities of Al wires

In order to obtain the Al wires with good mechanical properties and high electrical conductivities, conductive wires of Al-0.16 Zr, Al-0.16 Sc, Al-0.12Sc-0.04Zr（mass fraction, %） and pure Al（99.996%） were produced with the diameter of 9.5 mm by continuous rheo-extrusion technology, and the extruded materials were heat treated and analyzed. The results show that the separate additions of 0.16% Sc and 0.16% Zr to pure Al improve the ultimate tensile strength but reduce the electrical conductivity, and the similar trend is found in the Al-0.12Sc-0.04 Zr alloy. After the subsequent heat treatment, the wire with the optimum comprehensive properties is Al-0.12Sc-0.04 Zr alloy, of which the ultimate tensile strength and electrical conductivity reach 160 MPa and 64.03%（IACS）, respectively.

A Statistical Method for Characterizing CMOS Process Fluctuations in Subthreshold Current Mirrors

A novel method to characterize CMOS process fluctuations in subthreshold current mirrors （SCM） is reported. The proposed model is succinct in methodology and calculation complexity compared with previous statistical models. However,it provides favorable estimations of CMOS process fluctuations on the SCM circuit, which makes it promising for engineering applications. The model statistically abstracts physical parameters, which depend on the IC process, into random variables with certain mean values and standard deviations, while aggregating all the random impacts into a discrete martingale. The correctness of the proposed method is experimentally verified on an SCM circuit implemented in an SMIC 0.18μm CMOS 1P6M mixed signal process with a conversion factor of 100 in an input range from 100pA to lμA. The pro- posed theory successfully predicts - 10% of die-to-die fluctuation measured in the experiment, and also suggests the -lmV of threshold voltage standard deviation over a single die,which meets the process parameters suggested by the design kit from the foundry. The deviations between calculated probabilities and measured data are less than 8%. Meanwhile, pertinent suggestions concerning high fluctuation tolerance subthreshold analog circuit design are also made and discussed.

Flow stress behavior of high-purity Al-Cu-Mg alloy and microstructure evolution

The flow stress behavior of high-purity Al-Cu-Mg alloy under hot deformation conditions was studied by Gleeble-1500,with the deformation temperature range from 300 to 500 °C and the strain rate range from 0.01 to 10 s-1. From the true stress-true strain curve, the flow stress increases with the increasing of strain and tends to be constant after a peak value, showing dynamic recover, and the peak value of flow stress increases with the decreasing of deformation temperature and the increasing of strain rate.When the strain rate is 10 s-1 and the deformation temperature is higher than 400 °C, the flow stress shows dynamic recrystallization characteristic. TEM micrographs were used to reveal the evolution of microstructures. According to the processing map at true strain of 0.7, the feasible deformation conditions are high strain rate(>0.5 s-1) or 440-500 °C and 0.01-0.02 s-1.

Viscosity profile prediction of a heavy crude oil during lifting in two deep artesian wells

It has been known that the productivity of artesian wells is strongly dependent on the rheological properties of crude oils. This work targets two deep artesian wells(>5000 m) that are producing heavy crude oil. The impacts of well conditions including temperature, pressure and shear rate, on the crude oil rheology were comprehensively investigated and correlated using several empirical rheological models. The experimental data indicate that this heavy oil is very sensitive to temperature as result of microstructure change caused by hydrogen bonding. The rheological behavior of the heavy oil is also significantly impacted by the imposed pressure, i.e., the viscosity flow activation energy(Eμ) gently increases with the increasing pressure. The viscosity–shear rate data are well fitted to the power law model at low temperature. However, due to the transition of fluid feature at high temperature(Newtonian fluid), the measured viscosity was found to slightly deviate from the fitting data. Combining the evaluated correlations, the viscosity profile of the heavy crude oil in these two deep artesian wells as a function of well depth was predicted using the oilfield producing data.

Relationship between rheological behavior and flotation rate in slurry with different chalcopyrite and lizardite concentration

The relationship between viscosity/yield stress and flotation rate in different chalcopyrite and lizardite concentrations was investigated by zeta potential measurements,rheological tests,flotation experiments,and DerjguinLandau-Verwey-Overbeek theoretical calculation.Results indicated that the concentration of minerals would affect the viscosity and yield stress of the slurry.That is,the viscosity/yield stress in the slurry rises accordingly when the concentration of minerals increases.The increase in viscosity/yield stress in slurry is also unfavorable to the enrichment of chalcopyrite but is conducive to the entrainment of lizardite in either single or binary system.Specifically,the flotation rate of chalcopyrite decreases while that of lizardite increases with the rise in viscosity/yield stress.

Dynamic recrystallization behavior and kinetics of high strength steel

The dynamic recrystallization behavior of high strength steel during hot deformation was investigated.The hot compression test was conducted in the temperature range of 950-1150 °C under strain rates of 0.1,1 and 5 s-1.It is observed that dynamic recrystallization(DRX) is the main flow softening mechanism and the flow stress increases with decreasing temperature and increasing strain rate.The relationship between material constants(Q,n,α and ln A) and strain is identified by the sixth order polynomial fit.The constitutive model is developed to predict the flow stress of the material incorporating the strain softening effect and verified.Moreover,the critical characteristics of DRX are extracted from the stress-strain curves under different deformation conditions by linear regression.The dynamic recrystallization volume fraction decreases with increasing strain rate at a constant temperature or decreasing deformation temperature under a constant strain rate.The kinetics of DRX increases with increasing deformation temperature or strain rate.

Hot compressive deformation behavior and constitutive relationship of Al-Zn-Mg-Zr alloy with trace amounts of Sc

Abstract： The hot deformation behaviors of AI-Zn-Mg-Sc-Zr alloy were investigated in a temperature range of 340-500℃ and a strain rate range of 0.001-10 s 1 using uniaxial compression test on Gleeble-1500 thermal simulation machine. The results show that the flow stress increases with increasing strain and tends to be constant after a peak value. The flow stress increases with increasing strain rate and decreases with increasing deformation temperature. The phenomenon of dynamic recovery and dynamic recrystallization can be observed by microstructural evolutions. Based on the hyperbolic Arrhenius-type equation, the true stress-true strain data from the tests were employed to establish the constitutive equation considering the effect of the true strain on material constants （α, β, Q, n and A）, which reveals the dependence of the flow stress on strain, strain rate and deformation temperature. The predicted stress-strain curves are in good agreement with experimental results, which confirms that the developed constitutive equations are suitable to research the hot deformation behaviors of Al-Zn-Mg-Sc-Zr alloy.

Constitutive analysis of AZ31 magnesium alloy plate

The plastic deformation simulation of AZ31 magnesium alloy at different elevated temperatures （from 473 to 723 K） was performed on Gleeble-1500 thermal mechanical simulator at the strain rates of 0.01, 0.1, 1, 5 and 10 s-t and the maximum deformation degree of 80%. The relationship between the flow stress and deformation temperature as well as strain rate was analyzed. The materials parameters and the apparent activation energy were calculated. The constitutive relationship was established with a Zener-Hollomon （Z） parameter. The results show that the flow stress increases with the increase of strain rate at a constant temperature, but it decreases with the increase of deformation temperature at a constant strain rate. The apparent activation energy is estimated to be 129-153 kJ/mol, which is close to that for self-diffusion of magnesium. The established constitutive relationship can reflect the change of flow stress during hot deformation.

Scale-Free Properties in Traffic System

In this work, we propose a new model of evolution networks, which is based on the evolution of the traffic flow. In our method, the network growth does not take into account preferential attachment, and the attachment of new node is independent of the degree of nodes. Our aim is that employing the theory of evolution network, we give a further understanding about the dynamical evolution of the traffic flow. We investigate the probability distributions and scaling properties of the proposed model The simulation results indicate that in the proposed model, the distribution of the output connections can be well described by scale-free distribution. Moreover, the distribution of the connections is largely related to the traffic flow states, such as the exponential distribution （i.e., the scale-free distribution） and random distribution etc.

Hot deformation behavior and constitutive relationship of Q420qE steel

Isothermal compression tests at temperatures from 1 273 to l 423 K and strain rates from 0.1 to 10 s-q were carried out to investigate the flow behaviors of Q420qE steel. Stress-strain data collected from the tests were employed to establish the constitutive equation, in which the influence of strain was incorporated by considering the effect of strain on material constants Q, n, a, and lnA. The results show that the flow stress curves are dependent on the strain, strain rate and deformation temperature. They display typical dynamic recrystallization behavior and consist of three stages, i.e., hardening stage, softening stage and steady stage. The flow stress decreases with increasing the deformation temperature and decreasing the strain rate. In addition, the flow stress data predicted by the proposed constitutive model agree well with the corresponding experimental results, and the correlation coefficient and the average absolute relative error between them are 0.990 3 and 3.686%, respectively.

Dynamic modeling of twin roll casting AZ41 magnesium alloy during hot compression processing

A dynamic material model of Mg-4.51Al-1.19Zn-0.5Mn-0.5Ca(AZ41,mass fraction,%)magnesium alloy was put forward.The results show that the dynamic material model can characterize the deformation behavior and microstructure evolution and describe the relations among flow stress,strain,strain rates and deformation temperatures.Statistical analysis shows the validity of the proposed model.The model predicts that lower deformation temperature and higher strain rate cause the sharp strain hardening. Meanwhile,the flow stress curve turns into a steady state at high temperature and lower strain rate.The moderate temperature of 350 ℃and strain rate of 0.01 s-1 are appropriate to this alloy.

Effect of plunger number on hydraulic transformer's flow pulsation rate

In order to supply theoretical guidance to hydraulic transformer's design and application,the effect of the number of plungers in hydraulic transformer on its flow characteristic is analyzed,theoretical analysis and simulation are done on hydraulic transformer's flow characteristic when the number of plungers is different.Based on the working principle of swash plate piston hydraulic components,mathematical models of instantaneous flow and flow pulsation rate are built,and simulation study is done with MATLAB.As a result,the effect is found,and some conclusions worth referring to are obtained.

Analytical Solution of Smoluchowski Equation in Harmonic Oscillator Potential

Non-equilibrium fission has been described by diffusion model. In order to describe the diffusion process analytically, the analytical solution of Smoluchowski equation in harmonic oscillator potential is obtained. This analytical solution is able to describe the probability distribution and the diffusive current with the variable x and t. The results indicate that the probability distribution and the diffusive current are relevant to the initial distribution shape, initial position, and the nuclear temperature T; the time to reach the quasi-stationary state is proportional to friction coefficient beta, but is independent of the initial distribution status and the nuclear temperature T. The prerequisites of negative diffusive current are justified. This method provides an approach to describe the diffusion process for fissile process in complicated potentials analytically.

Flow behavior and fracture of Al−Mg−Si alloy at cryogenic temperatures

The tensile and fracture behaviors of AA6061 alloy were investigated in order to provide quantitative data about this alloy at cryogenic temperatures.Specimens of AA6061 alloy were solution heat treated before tensile tests at 298,173 and 77 K and tested at strain rates in the range from 0.1 to 0.0001 s^(−1).The results indicate the suppression of the Portevin−Le Chatelier(PLC)effect and dynamic strain aging(DSA)at 77 K.In contrast,at 298 K,a remarkable serrated flow,characteristic of the PLC effect,is observed.Furthermore,the tensile behavior at 77 K,compared with that observed at 173 and 298 K,shows a simultaneous increase in strength,uniform elongation,modulus of toughness,strain-hardening exponent and strain rate sensitivity,which is related to a decrease in the dynamic recovery rate at low temperature.These responses are reflected on the fracture morphology,since the dimple size decreases at 77 K,while the area covered by dimples increases.Comparisons of the Johnson−Cook model show that a good agreement can be obtained for tests at 173 and 77 K,in which DSA is suppressed.

Creep properties and permeability evolution in triaxial rheological tests of hard rock in dam foundation

Triaxial creep tests were carried out under seepage pressure by using rock servo-controlled triaxial rheology testing equipment. Based on experimental results, rock rheological properties influenced by seepage-stress coupling were studied, and variations of seepage rate with time in complete creep processes of rock were analyzed. It is shown that, when the applied stress is less than failure stress level, the creep deformation is not obvious, and its main form is steady-state creep. When applied stress level is greater than or less than but close to fracture stress, it is easier to see the increase of creep deformation and the more obvious accelerative creep characteristics. The circumferential creep deformation is obviously higher than the axial creep deformation. At the stage of steady-state creep, the average of seepage flow rate is about 4.7×10-9 rn/s at confining pressure （tr3） of 2 MPa, and is about 3.9×10-9 m/s at a3 of 6 MPa. It is seen that the seepage flow rate at or3 of 2 MPa in this case is obviously larger than that at tr3 of 6 MPa. At the stage of creep acceleration, the seepage flow rate is markedly increased with the increase of time. The variation of rock permeability is directly connected to the growth and evolution of creep crack. It is suggested that the permeability coefficient in complete creep processes of rock is not a constant, but is a function of rock creep strain, confining pressure, damage variable and pore water pressure. The results can be considered to provide a reliable reference for the establishment of rock rheological model and parameter identification.

Intraseasonal variability of summer monsoon rainfall over the lower reaches of the Yangtze River basin

This work investigates the boreal-summer intraseasonal variability(ISV)of the precipitation over the lower reaches of the Yangtze River basin(LYRB)during 1979–2016,based on daily Climate Prediction Center global precipitation data.The ISV of the summer monsoon rainfall over the LYRB is mainly dominated by the lower-frequency 12–20-day variability and the higher-frequency 8–12-day variability.The lower-frequency variability is found to be related to the northwestwardpropagating quasi-biweekly oscillation(QBWO)over the western North Pacific spanning the South China Sea(SCS)and Philippine Sea,while the higher-frequency variability is related to the southeastward propagating midlatitude wave train(MLWT).Moreover,not each active QBWO(MLWT)in the SCS(East Asia)can generate ISV components of the precipitation anomaly over the LYRB.The QBWO can change the rainfall significantly with the modulation of mean state precipitation,while the quasi-11-day mode mainly depends on the intensity of the MLWT rather than the mean precipitation change.These findings should enrich our understanding of the ISV of the East Asian summer monsoon and improve its predictability.

The Relationship between the Interdecadal Variation of Summer Precipitation and Its Interannual Variability over the Middle and Lower Reaches of the Yangtze River Valley

The intensity of summer precipitation interannual variability is strongest over the middle and lower reaches of the Yangtze River Valley(MLYRV). The variability is larger than 1.5 mm d–1 and up to 35%–40% of the climatological mean summer precipitation. The relationship between the interdecadal change in the intensity of summer precipitation and its interannual variability over this area is investigated, by analyzing five gauged and re-constructed precipitation datasets. The relationship is found to be very weak over the MLYRV, with a correlation coefficient of only approximately 0.10. The Pacific Decadal Oscillation influences the western North Pacific subtropical high, which is responsible for the interdecadal change in summer precipitation over the MLYRV. However, the precipitation interannual variability is closely related to the ENSO events in the preceding winter due to its impact on the meridional displacement of the East Asian westerly jet. Different physical mechanisms cause different interdecadal variation in the intensity of summer precipitation and its interannual variability, and thus result in a poor relationship.

Microstructure evolution and its effect on flow stress of TC17 alloy during deformation in α+β two-phase region

The microstructure evolution and its effect on flow stress of TC17 alloy during deformation in the α+β two-phase region were investigated via microstructure characterization and isothermal compression tests. Results showed that the spheroidized rate of α phase at 820 and 850℃ slightly increased with increasing strain. With increasing deformation temperature, the spheroidized rate of α phase showed a slight increasing trend, but the volume fraction of α phase significantly decreased. The flow stress at 780 ℃ and 1 s^-1 decreased continuously and steady state condition was not achieved up to strain of 1.2 due to dislocation annihilation and α lamellae rotation. Under this condition, the dynamic spheroidization was retarded. At the deformation temperatures of 820 and 850℃, and a strain rate of 1 s^-1, a steady state flow stress was observed at strains above 0.8 due to the balance between work hardening and dynamic softening. The dynamic softening was attributed to the α lamellae rotation, dynamic recovery and a little spheroidization.