This paper investigates the data collection in an unmanned aerial vehicle(UAV)-aided Internet of Things(IoT) network, where a UAV is dispatched to collect data from ground sensors in a practical and accurate probabili...This paper investigates the data collection in an unmanned aerial vehicle(UAV)-aided Internet of Things(IoT) network, where a UAV is dispatched to collect data from ground sensors in a practical and accurate probabilistic line-of-sight(LoS) channel. Especially, access points(APs) are introduced to collect data from some sensors in the unlicensed band to improve data collection efficiency. We formulate a mixed-integer non-convex optimization problem to minimize the UAV flight time by jointly designing the UAV 3D trajectory and sensors’ scheduling, while ensuring the required amount of data can be collected under the limited UAV energy. To solve this nonconvex problem, we recast the objective problem into a tractable form. Then, the problem is further divided into several sub-problems to solve iteratively, and the successive convex approximation(SCA) scheme is applied to solve each non-convex subproblem. Finally,the bisection search is adopted to speed up the searching for the minimum UAV flight time. Simulation results verify that the UAV flight time can be shortened by the proposed method effectively.展开更多
Wireless Sensor Network(WSN)is widely utilized in large-scale distributed unmanned detection scenarios due to its low cost and flexible installation.However,WSN data collection encounters challenges in scenarios lacki...Wireless Sensor Network(WSN)is widely utilized in large-scale distributed unmanned detection scenarios due to its low cost and flexible installation.However,WSN data collection encounters challenges in scenarios lacking communication infrastructure.Unmanned aerial vehicle(UAV)offers a novel solution for WSN data collection,leveraging their high mobility.In this paper,we present an efficient UAV-assisted data collection algorithm aimed at minimizing the overall power consumption of the WSN.Firstly,a two-layer UAV-assisted data collection model is introduced,including the ground and aerial layers.The ground layer senses the environmental data by the cluster members(CMs),and the CMs transmit the data to the cluster heads(CHs),which forward the collected data to the UAVs.The aerial network layer consists of multiple UAVs that collect,store,and forward data from the CHs to the data center for analysis.Secondly,an improved clustering algorithm based on K-Means++is proposed to optimize the number and locations of CHs.Moreover,an Actor-Critic based algorithm is introduced to optimize the UAV deployment and the association with CHs.Finally,simulation results verify the effectiveness of the proposed algorithms.展开更多
Large-scale wireless sensor networks(WSNs)play a critical role in monitoring dangerous scenarios and responding to medical emergencies.However,the inherent instability and error-prone nature of wireless links present ...Large-scale wireless sensor networks(WSNs)play a critical role in monitoring dangerous scenarios and responding to medical emergencies.However,the inherent instability and error-prone nature of wireless links present significant challenges,necessitating efficient data collection and reliable transmission services.This paper addresses the limitations of existing data transmission and recovery protocols by proposing a systematic end-to-end design tailored for medical event-driven cluster-based large-scale WSNs.The primary goal is to enhance the reliability of data collection and transmission services,ensuring a comprehensive and practical approach.Our approach focuses on refining the hop-count-based routing scheme to achieve fairness in forwarding reliability.Additionally,it emphasizes reliable data collection within clusters and establishes robust data transmission over multiple hops.These systematic improvements are designed to optimize the overall performance of the WSN in real-world scenarios.Simulation results of the proposed protocol validate its exceptional performance compared to other prominent data transmission schemes.The evaluation spans varying sensor densities,wireless channel conditions,and packet transmission rates,showcasing the protocol’s superiority in ensuring reliable and efficient data transfer.Our systematic end-to-end design successfully addresses the challenges posed by the instability of wireless links in large-scaleWSNs.By prioritizing fairness,reliability,and efficiency,the proposed protocol demonstrates its efficacy in enhancing data collection and transmission services,thereby offering a valuable contribution to the field of medical event-drivenWSNs.展开更多
This study addressed the issues related to the collection and management of basic data for railway green performance. A railway green performance basic database has been constructed based on metadata and data exchange...This study addressed the issues related to the collection and management of basic data for railway green performance. A railway green performance basic database has been constructed based on metadata and data exchange schemas. A data classification system has been established from the perspectives of businesses, processes,and entities. A BIM(Building Information Modelling) model data extraction scheme is proposed based on field similarity matching and a document content extraction scheme is proposed based on image recognition. A railway green performance basic data collection system has been developed, achieving efficient collection and integrated management of railway green performance basic data. This system can provide data support for applications such as railway carbon emissions accounting, green cost-benefit analysis, and evaluation of green design solutions.展开更多
This paper considers a time-constrained data collection problem from a network of ground sensors located on uneven terrain by an Unmanned Aerial Vehicle(UAV),a typical Unmanned Aerial System(UAS).The ground sensors ha...This paper considers a time-constrained data collection problem from a network of ground sensors located on uneven terrain by an Unmanned Aerial Vehicle(UAV),a typical Unmanned Aerial System(UAS).The ground sensors harvest renewable energy and are equipped with batteries and data buffers.The ground sensor model takes into account sensor data buffer and battery limitations.An asymptotically globally optimal method of joint UAV 3D trajectory optimization and data transmission schedule is developed.The developed method maximizes the amount of data transmitted to the UAV without losses and too long delays and minimizes the propulsion energy of the UAV.The developed algorithm of optimal trajectory optimization and transmission scheduling is based on dynamic programming.Computer simulations demonstrate the effectiveness of the proposed algorithm.展开更多
As the sixth generation network(6G)emerges,the Internet of remote things(IoRT)has become a critical issue.However,conventional terrestrial networks cannot meet the delay-sensitive data collection needs of IoRT network...As the sixth generation network(6G)emerges,the Internet of remote things(IoRT)has become a critical issue.However,conventional terrestrial networks cannot meet the delay-sensitive data collection needs of IoRT networks,and the Space-Air-Ground integrated network(SAGIN)holds promise.We propose a novel setup that integrates non-orthogonal multiple access(NOMA)and wireless power transfer(WPT)to collect latency-sensitive data from IoRT networks.To extend the lifetime of devices,we aim to minimize the maximum energy consumption among all IoRT devices.Due to the coupling between variables,the resulting problem is non-convex.We first decouple the variables and split the original problem into four subproblems.Then,we propose an iterative algorithm to solve the corresponding subproblems based on successive convex approximation(SCA)techniques and slack variables.Finally,simulation results show that the NOMA strategy has a tremendous advantage over the OMA scheme in terms of network lifetime and energy efficiency,providing valuable insights.展开更多
Autonomous underwater vehicle(AUV)-assisted data collection is an efficient approach to implementing smart ocean.However,the data collection in time-varying ocean currents is plagued by two critical issues:AUV yaw and...Autonomous underwater vehicle(AUV)-assisted data collection is an efficient approach to implementing smart ocean.However,the data collection in time-varying ocean currents is plagued by two critical issues:AUV yaw and sensor node movement.We propose an adaptive AUV-assisted data collection strategy for ocean currents to address these issues.First,we consider the energy consumption of an AUV in conjunction with the value of information(VoI)over the sensor nodes and formulate an optimization problem to maximize the VoI-energy ratio.The AUV yaw problem is then solved by deriving the AUV's reachable region in different ocean current environments and the optimal cruising direction to the target nodes.Finally,using the predicted VoI-energy ratio,we sequentially design a distributed path planning algorithm to select the next target node for AUV.The simulation results indicate that the proposed strategy can utilize ocean currents to aid AUV navigation,thereby reducing the AUV's energy consumption and ensuring timely data collection.展开更多
Underwater magnetic induction(MI)-assisted acoustic cooperative multiple-input-multipleoutput(MIMO) has been recently proposed as a promising technique for underwater wireless sensor networks(UWSNs).For the more,the e...Underwater magnetic induction(MI)-assisted acoustic cooperative multiple-input-multipleoutput(MIMO) has been recently proposed as a promising technique for underwater wireless sensor networks(UWSNs).For the more,the energy utilization of energy-constrained sensor nodes is one of the key issues in UWSNs,and it relates to the network lifetime.In this paper,we present an energy-efficient data collection for underwater MI-assisted acoustic cooperative MIMO wireless sensor networks(WSNs),including the formation of cooperative MIMO and relay link establishment.Firstly,the cooperative MIMO is formed by considering its expected transmission range and the energy balance of nodes with it.Particularly,from the perspective of the node’s energy consumption,the expected cooperative MIMO size and the selection of master node(MN) are proposed.Sequentially,to improve the coverage of the networks and prolong the network lifetime,relay links are established by relay selection algorithm that using matching theory.Finally,the simulation results show that the proposed data collection improves its efficiency,reduces the energy consumption of the master node,improves the networks’ coverage,and extends the network lifetime.展开更多
Unmanned aerial vehicles(UAVs) are advantageous for data collection in wireless sensor networks(WSNs) due to its low cost of use,flexible deployment,controllable mobility,etc. However,how to cope with the inherent iss...Unmanned aerial vehicles(UAVs) are advantageous for data collection in wireless sensor networks(WSNs) due to its low cost of use,flexible deployment,controllable mobility,etc. However,how to cope with the inherent issues of energy limitation and data security in the WSNs is challenging in such an application paradigm. To this end,based on the framework of physical layer security,an optimization problem for maximizing secrecy energy efficiency(EE) of data collection is formulated,which focuses on optimizing the UAV’s positions and the sensors’ transmit power. To overcome the difficulties in solving the optimization problem,the methods of fractional programming and successive convex approximation are then adopted to gradually transform the original problem into a series of tractable subproblems which are solved in an iterative manner. As shown in simulation results,by the joint designs in the spatial domain of UAV and the power domain of sensors,the proposed algorithm achieves a significant improvement of secrecy EE and rate.展开更多
The first part of this report describes the data reduction of non-merohedrally twinned crystals measured on Bruker and Agilent area-detector diffractometers. The image frames of methyl-2-aminopyrazine-3-carboxylate we...The first part of this report describes the data reduction of non-merohedrally twinned crystals measured on Bruker and Agilent area-detector diffractometers. The image frames of methyl-2-aminopyrazine-3-carboxylate were processed with APEX2 to furnish a set of overlapping diffraction indices that were used for solution and refinement. CrysAlisPRO was used for processing the frames of bis(diethyldicarbamato)nickel, which exists in monoclinic and tetragonal polymorphs, and in untwinned and twinned forms. In the second part, the crystal structure of [(3-formyl-4- hydroxyphenyl)methyl]triphenylphosphanium chloride was refined through the ‘HKLF 5'(based on a combined set of diffraction indices) and PLATON(based on one set of diffraction indices) routes to give identical outcomes because the amount of overlap of the twin domains is small. For the third part, in a proof-of-concept investigation, the diffraction pattern of untwinned and twinned 4-{(E)-(4-aminophenyl)diazenyl]phenylamine was recorded simultaneously in one run; the three domains could be indexed and the crystal structure satisfactorily refined. The refinement was identical to those derived from independent measurements; the crystal structure features two independent centrosymmetric molecules, one of which is ordered and the other whole-molecule-disordered. This two-in-one run opens up the possibility that two or more crystals having different atomic compositions can be measured simultaneously if their reciprocal lattices do not overlap significantly.展开更多
With technological advancements in 6G and Internet of Things(IoT), the incorporation of Unmanned Aerial Vehicles (UAVs) and cellularnetworks has become a hot research topic. At present, the proficient evolution of 6G ...With technological advancements in 6G and Internet of Things(IoT), the incorporation of Unmanned Aerial Vehicles (UAVs) and cellularnetworks has become a hot research topic. At present, the proficient evolution of 6G networks allows the UAVs to offer cost-effective and timelysolutions for real-time applications such as medicine, tracking, surveillance,etc. Energy efficiency, data collection, and route planning are crucial processesto improve the network communication. These processes are highly difficultowing to high mobility, presence of non-stationary links, dynamic topology,and energy-restricted UAVs. With this motivation, the current research paperpresents a novel Energy Aware Data Collection with Routing Planning for6G-enabled UAV communication (EADCRP-6G) technique. The goal of theproposed EADCRP-6G technique is to conduct energy-efficient cluster-baseddata collection and optimal route planning for 6G-enabled UAV networks.EADCRP-6G technique deploys Improved Red Deer Algorithm-based Clustering (IRDAC) technique to elect an optimal set of Cluster Heads (CH) andorganize these clusters. Besides, Artificial Fish Swarm-based Route Planning(AFSRP) technique is applied to choose an optimum set of routes for UAVcommunication in 6G networks. In order to validated whether the proposedEADCRP-6G technique enhances the performance, a series of simulationswas performed and the outcomes were investigated under different dimensions.The experimental results showcase that the proposed model outperformed allother existing models under different evaluation parameters.展开更多
In recent times,sixth generation(6G)communication technologies have become a hot research topic because of maximum throughput and low delay services for mobile users.It encompasses several heterogeneous resource and c...In recent times,sixth generation(6G)communication technologies have become a hot research topic because of maximum throughput and low delay services for mobile users.It encompasses several heterogeneous resource and communication standard in ensuring incessant availability of service.At the same time,the development of 6G enables the Unmanned Aerial Vehicles(UAVs)in offering cost and time-efficient solution to several applications like healthcare,surveillance,disaster management,etc.In UAV networks,energy efficiency and data collection are considered the major process for high quality network communication.But these procedures are found to be challenging because of maximum mobility,unstable links,dynamic topology,and energy restricted UAVs.These issues are solved by the use of artificial intelligence(AI)and energy efficient clustering techniques for UAVs in the 6G environment.With this inspiration,this work designs an artificial intelligence enabled cooperative cluster-based data collection technique for unmanned aerial vehicles(AECCDC-UAV)in 6G environment.The proposed AECCDC-UAV technique purposes for dividing the UAV network as to different clusters and allocate a cluster head(CH)to each cluster in such a way that the energy consumption(ECM)gets minimized.The presented AECCDC-UAV technique involves a quasi-oppositional shuffled shepherd optimization(QOSSO)algorithm for selecting the CHs and construct clusters.The QOSSO algorithm derives a fitness function involving three input parameters residual energy of UAVs,distance to neighboring UAVs,and degree of UAVs.The performance of the AECCDC-UAV technique is validated in many aspects and the obtained experimental values demonstration promising results over the recent state of art methods.展开更多
With the rapid developments of Internet of Things(IoT)and proliferation of embedded devices,large volume of personal data are collected,which however,might carry massive private information about attributes that users...With the rapid developments of Internet of Things(IoT)and proliferation of embedded devices,large volume of personal data are collected,which however,might carry massive private information about attributes that users do not want to share.Many privacy-preserving methods have been proposed to prevent privacy leakage by perturbing raw data or extracting task-oriented features at local devices.Unfortunately,they would suffer from significant privacy leakage and accuracy drop when applied to other tasks as they are designed and optimized for predefined tasks.In this paper,we propose a novel task-free privacy-preserving data collection method via adversarial representation learning,called TF-ARL,to protect private attributes specified by users while maintaining data utility for unknown downstream tasks.To this end,we first propose a privacy adversarial learning mechanism(PAL)to protect private attributes by optimizing the feature extractor to maximize the adversary’s prediction uncertainty on private attributes,and then design a conditional decoding mechanism(ConDec)to maintain data utility for downstream tasks by minimizing the conditional reconstruction error from the sanitized features.With the joint learning of PAL and ConDec,we can learn a privacy-aware feature extractor where the sanitized features maintain the discriminative information except privacy.Extensive experimental results on real-world datasets demonstrate the effectiveness of TF-ARL.展开更多
Exploiting mobile elements (MEs) to accomplish data collection in wireless sensor networks (WSNs) can improve the energy efficiency of sensor nodes, and prolong network lifetime. However, it will lead to large dat...Exploiting mobile elements (MEs) to accomplish data collection in wireless sensor networks (WSNs) can improve the energy efficiency of sensor nodes, and prolong network lifetime. However, it will lead to large data collection latency for the network, which is unacceptable for data-critical applications. In this paper, we address this problem by minimizing the traveling length of MEs. Our methods mainly consist of two steps: we first construct a virtual grid network and select the minimal stop point set (SPS) from it; then, we make optimal scheduling for the MEs based on the SPS in order to minimize their traveling length. Different implementations of genetic algorithm (GA) are used to solve the problem. Our methods are evaluated by extensive simulations. The results show that these methods can greatly reduce the traveling length of MEs, and decrease the data collection latency.展开更多
In this paper we describe a system used to control,collect and process data in an 8 mm portable microwave radiometer scatterometer .We focus on hardware and software design of the system based on a PIC16F874 chip. T...In this paper we describe a system used to control,collect and process data in an 8 mm portable microwave radiometer scatterometer .We focus on hardware and software design of the system based on a PIC16F874 chip. The system has been successfully used in an 8 mm portable microwave radiometer scatterometer. Compared with other similar systems, the system modularization, miniaturization and intelligentization are improved so as to meet portable instrument requirements.展开更多
In the IoT(Internet of Things)system,the introduction of UAV(Unmanned Aerial Vehicle)as a new data collection platform can solve the problem that IoT devices are unable to transmit data over long distances due to the ...In the IoT(Internet of Things)system,the introduction of UAV(Unmanned Aerial Vehicle)as a new data collection platform can solve the problem that IoT devices are unable to transmit data over long distances due to the limitation of their battery energy.However,the unreasonable distribution of UAVs will still lead to the problem of the high total energy consumption of the system.In this work,to deal with the problem,a deployment model of a mobile edge computing(MEC)system based on multi-UAV is proposed.The goal of the model is to minimize the energy consumption of the system in the process of data transmission by optimizing the deployment of UAVs.The DEVIPSK(differential evolution algorithm with variable population size based on a mutation strategy pool initialized by K-Means)is proposed to solve the model.In DEVIPSK,the population is initialized by K-Means to obtain better initial positions of UAVs.Besides,considering the limitation of the fixed mutation strategy in the traditional evolutionary algorithm,a mutation strategy pool is used to update the positions of UAVs.The experimental results show the superiority of the DEVIPSK and provide guidance for the deployment of UAVs in the field of edge data collection in the IoT system.展开更多
Traffic data collection is essential for performance assessment, safety improvement and road planning. While automated traffic data collection for highways is relatively mature, that for roundabouts is more challengin...Traffic data collection is essential for performance assessment, safety improvement and road planning. While automated traffic data collection for highways is relatively mature, that for roundabouts is more challenging due to more complex traffic scenes, data specifications and vehicle behavior. In this paper, the authors propose an automated traffic data collection system dedicated to roundabout scenes. The proposed system has mainly four steps of processing. First, camera calibration is performed for roundabout traffic scenes with a novel circle-based calibration algorithm. Second, the system uses enhanced Mixture of Gaussian algorithm with shaking removal for video segmentation, which can tolerate repeated camera displacements and background movements. Then, Kalman filtering, Kemel-based tracking and overlap-based opti- mization are employed to track vehicles while they are occluded and to derive the complete vehicle trajectories. The resulting vehicle trajectory of each individual vehicle gives the position, size, shape and speed of the vehicle at each time moment. Finally, a data mining algorithm is used to automatically extract the interested traffic data from the vehicle trajectories. The overall traffic data collection system has been implemented in software and runs on regular PC. The total processing time for a 3-hour video is currently 6 h. The automated traffic data collection system can significantly reduce cost and improve efficiency compared to manual data collection. The extracted traffic data have been compared to accurate manual measurements for 29 videos recorded on 29 different days, and an accuracy of more than 90% has been achieved.展开更多
With the rapid spread of smart sensors,data collection is becoming more and more important in Mobile Edge Networks(MENs).The collected data can be used in many applications based on the analysis results of these data ...With the rapid spread of smart sensors,data collection is becoming more and more important in Mobile Edge Networks(MENs).The collected data can be used in many applications based on the analysis results of these data by cloud computing.Nowadays,data collection schemes have been widely studied by researchers.However,most of the researches take the amount of collected data into consideration without thinking about the problem of privacy leakage of the collected data.In this paper,we propose an energy-efficient and anonymous data collection scheme for MENs to keep a balance between energy consumption and data privacy,in which the privacy information of senors is hidden during data communication.In addition,the residual energy of nodes is taken into consideration in this scheme in particular when it comes to the selection of the relay node.The security analysis shows that no privacy information of the source node and relay node is leaked to attackers.Moreover,the simulation results demonstrate that the proposed scheme is better than other schemes in aspects of lifetime and energy consumption.At the end of the simulation part,we present a qualitative analysis for the proposed scheme and some conventional protocols.It is noteworthy that the proposed scheme outperforms the existing protocols in terms of the above indicators.展开更多
We suggest event collection protocol in a specific region where sensors are deployed to detect and collect events.In the traditional multi-hop routing in wireless sensor networks reporting events to a sink node or bas...We suggest event collection protocol in a specific region where sensors are deployed to detect and collect events.In the traditional multi-hop routing in wireless sensor networks reporting events to a sink node or base-station will cause imbalanced energy consumption of static sensors.To solve this problem,we use mobile sink.In this paper,we study the design of efficiency routing protocol for supporting efficient data collecting in mobile sink wireless sensor networks(mWSNs).We suggest the following two main ideas.First,we use reactive protocol to cut off unnecessary delay.Mobile sink makes a path to access to sensor node.Second,we model mobile sink movement depending on data frequency,so we can reduce moving distance efficiently.We simulate this protocol and compare it with the traditional method.Simulation results show this protocol reduces distance significantly and is suitable for mWSNs with heavy traffic.展开更多
<div style="text-align:justify;"> Due to its air superiority and high mobility, unmanned aerial vehicle (UAV) can obtain better line-of-sight (LoS) link transmission channel. Therefore, UAV assisted da...<div style="text-align:justify;"> Due to its air superiority and high mobility, unmanned aerial vehicle (UAV) can obtain better line-of-sight (LoS) link transmission channel. Therefore, UAV assisted data collection for wireless sensor networks (WSNs) has become an important research direction. This paper intends to minimize the loss of WSNs for the robust data acquisition and communication assisted by UAV under the imperfect channel state information (CSI). On the premise of ensuring the completion of the communication task, we jointly optimize the wake-up schedule of SNs and the flight trajectory of the UAV, by considering the flight speed of the UAV and the sparse access of all sensor nodes (SNs) in WSN. Because the formulated optimization problem is a mixed integer nonconvex problem, we decompose the original problem into the efficient suboptimal solutions to overcome the difficulty of the optimization. Finally, the number of access node corresponding to the optimized operation time and access efficiency is induced for the entire WSN system efficiency improving. The simulation shows the performance gains of our proposed scheme and the influences of the system parameters are analyzed. </div>展开更多
基金supported by the National Key Research and Development Program under Grant 2022YFB3303702the Key Program of National Natural Science Foundation of China under Grant 61931001+1 种基金supported by the National Natural Science Foundation of China under Grant No.62203368the Natural Science Foundation of Sichuan Province under Grant No.2023NSFSC1440。
文摘This paper investigates the data collection in an unmanned aerial vehicle(UAV)-aided Internet of Things(IoT) network, where a UAV is dispatched to collect data from ground sensors in a practical and accurate probabilistic line-of-sight(LoS) channel. Especially, access points(APs) are introduced to collect data from some sensors in the unlicensed band to improve data collection efficiency. We formulate a mixed-integer non-convex optimization problem to minimize the UAV flight time by jointly designing the UAV 3D trajectory and sensors’ scheduling, while ensuring the required amount of data can be collected under the limited UAV energy. To solve this nonconvex problem, we recast the objective problem into a tractable form. Then, the problem is further divided into several sub-problems to solve iteratively, and the successive convex approximation(SCA) scheme is applied to solve each non-convex subproblem. Finally,the bisection search is adopted to speed up the searching for the minimum UAV flight time. Simulation results verify that the UAV flight time can be shortened by the proposed method effectively.
基金supported by the National Natural Science Foundation of China(NSFC)(61831002,62001076)the General Program of Natural Science Foundation of Chongqing(No.CSTB2023NSCQ-MSX0726,No.cstc2020jcyjmsxmX0878).
文摘Wireless Sensor Network(WSN)is widely utilized in large-scale distributed unmanned detection scenarios due to its low cost and flexible installation.However,WSN data collection encounters challenges in scenarios lacking communication infrastructure.Unmanned aerial vehicle(UAV)offers a novel solution for WSN data collection,leveraging their high mobility.In this paper,we present an efficient UAV-assisted data collection algorithm aimed at minimizing the overall power consumption of the WSN.Firstly,a two-layer UAV-assisted data collection model is introduced,including the ground and aerial layers.The ground layer senses the environmental data by the cluster members(CMs),and the CMs transmit the data to the cluster heads(CHs),which forward the collected data to the UAVs.The aerial network layer consists of multiple UAVs that collect,store,and forward data from the CHs to the data center for analysis.Secondly,an improved clustering algorithm based on K-Means++is proposed to optimize the number and locations of CHs.Moreover,an Actor-Critic based algorithm is introduced to optimize the UAV deployment and the association with CHs.Finally,simulation results verify the effectiveness of the proposed algorithms.
文摘Large-scale wireless sensor networks(WSNs)play a critical role in monitoring dangerous scenarios and responding to medical emergencies.However,the inherent instability and error-prone nature of wireless links present significant challenges,necessitating efficient data collection and reliable transmission services.This paper addresses the limitations of existing data transmission and recovery protocols by proposing a systematic end-to-end design tailored for medical event-driven cluster-based large-scale WSNs.The primary goal is to enhance the reliability of data collection and transmission services,ensuring a comprehensive and practical approach.Our approach focuses on refining the hop-count-based routing scheme to achieve fairness in forwarding reliability.Additionally,it emphasizes reliable data collection within clusters and establishes robust data transmission over multiple hops.These systematic improvements are designed to optimize the overall performance of the WSN in real-world scenarios.Simulation results of the proposed protocol validate its exceptional performance compared to other prominent data transmission schemes.The evaluation spans varying sensor densities,wireless channel conditions,and packet transmission rates,showcasing the protocol’s superiority in ensuring reliable and efficient data transfer.Our systematic end-to-end design successfully addresses the challenges posed by the instability of wireless links in large-scaleWSNs.By prioritizing fairness,reliability,and efficiency,the proposed protocol demonstrates its efficacy in enhancing data collection and transmission services,thereby offering a valuable contribution to the field of medical event-drivenWSNs.
基金supported by the Science and Technology Research and Development Plan of China State Railway Group Co.,Ltd.(L2023Z001).
文摘This study addressed the issues related to the collection and management of basic data for railway green performance. A railway green performance basic database has been constructed based on metadata and data exchange schemas. A data classification system has been established from the perspectives of businesses, processes,and entities. A BIM(Building Information Modelling) model data extraction scheme is proposed based on field similarity matching and a document content extraction scheme is proposed based on image recognition. A railway green performance basic data collection system has been developed, achieving efficient collection and integrated management of railway green performance basic data. This system can provide data support for applications such as railway carbon emissions accounting, green cost-benefit analysis, and evaluation of green design solutions.
基金funding from the Australian Government,via Grant No.AUSMURIB000001 associated with ONR MURI Grant No.N00014-19-1-2571。
文摘This paper considers a time-constrained data collection problem from a network of ground sensors located on uneven terrain by an Unmanned Aerial Vehicle(UAV),a typical Unmanned Aerial System(UAS).The ground sensors harvest renewable energy and are equipped with batteries and data buffers.The ground sensor model takes into account sensor data buffer and battery limitations.An asymptotically globally optimal method of joint UAV 3D trajectory optimization and data transmission schedule is developed.The developed method maximizes the amount of data transmitted to the UAV without losses and too long delays and minimizes the propulsion energy of the UAV.The developed algorithm of optimal trajectory optimization and transmission scheduling is based on dynamic programming.Computer simulations demonstrate the effectiveness of the proposed algorithm.
基金supported by National Natural Science Foundation of China(No.62171158)the project“The Major Key Project of PCL(PCL2021A03-1)”from Peng Cheng Laboratorysupported by the Science and the Research Fund Program of Guangdong Key Laboratory of Aerospace Communication and Networking Technology(2018B030322004).
文摘As the sixth generation network(6G)emerges,the Internet of remote things(IoRT)has become a critical issue.However,conventional terrestrial networks cannot meet the delay-sensitive data collection needs of IoRT networks,and the Space-Air-Ground integrated network(SAGIN)holds promise.We propose a novel setup that integrates non-orthogonal multiple access(NOMA)and wireless power transfer(WPT)to collect latency-sensitive data from IoRT networks.To extend the lifetime of devices,we aim to minimize the maximum energy consumption among all IoRT devices.Due to the coupling between variables,the resulting problem is non-convex.We first decouple the variables and split the original problem into four subproblems.Then,we propose an iterative algorithm to solve the corresponding subproblems based on successive convex approximation(SCA)techniques and slack variables.Finally,simulation results show that the NOMA strategy has a tremendous advantage over the OMA scheme in terms of network lifetime and energy efficiency,providing valuable insights.
基金supported by the National Natural Science Foundation of China(62071472,62101556)the Natural Science Foundation of Jiangsu province(BK20200650,BK20210489)the Future Network Scientific Research Fund Project(FNSRFP2021-YB-12)。
文摘Autonomous underwater vehicle(AUV)-assisted data collection is an efficient approach to implementing smart ocean.However,the data collection in time-varying ocean currents is plagued by two critical issues:AUV yaw and sensor node movement.We propose an adaptive AUV-assisted data collection strategy for ocean currents to address these issues.First,we consider the energy consumption of an AUV in conjunction with the value of information(VoI)over the sensor nodes and formulate an optimization problem to maximize the VoI-energy ratio.The AUV yaw problem is then solved by deriving the AUV's reachable region in different ocean current environments and the optimal cruising direction to the target nodes.Finally,using the predicted VoI-energy ratio,we sequentially design a distributed path planning algorithm to select the next target node for AUV.The simulation results indicate that the proposed strategy can utilize ocean currents to aid AUV navigation,thereby reducing the AUV's energy consumption and ensuring timely data collection.
基金supported in part by the program for "Industrial Io T and Emergency Collaboration" Innovative Research Team in CUMT (No.2020ZY002)in part by the Postgraduate Research&Practice Innovation Program of Jiangsu Province,2021WLKXJ054Postgraduate Research&Practice Innovation Program of China University of Mining and Technology,KYCX21_2242
文摘Underwater magnetic induction(MI)-assisted acoustic cooperative multiple-input-multipleoutput(MIMO) has been recently proposed as a promising technique for underwater wireless sensor networks(UWSNs).For the more,the energy utilization of energy-constrained sensor nodes is one of the key issues in UWSNs,and it relates to the network lifetime.In this paper,we present an energy-efficient data collection for underwater MI-assisted acoustic cooperative MIMO wireless sensor networks(WSNs),including the formation of cooperative MIMO and relay link establishment.Firstly,the cooperative MIMO is formed by considering its expected transmission range and the energy balance of nodes with it.Particularly,from the perspective of the node’s energy consumption,the expected cooperative MIMO size and the selection of master node(MN) are proposed.Sequentially,to improve the coverage of the networks and prolong the network lifetime,relay links are established by relay selection algorithm that using matching theory.Finally,the simulation results show that the proposed data collection improves its efficiency,reduces the energy consumption of the master node,improves the networks’ coverage,and extends the network lifetime.
基金Supported by the National Natural Science Foundation of China(No.61871401).
文摘Unmanned aerial vehicles(UAVs) are advantageous for data collection in wireless sensor networks(WSNs) due to its low cost of use,flexible deployment,controllable mobility,etc. However,how to cope with the inherent issues of energy limitation and data security in the WSNs is challenging in such an application paradigm. To this end,based on the framework of physical layer security,an optimization problem for maximizing secrecy energy efficiency(EE) of data collection is formulated,which focuses on optimizing the UAV’s positions and the sensors’ transmit power. To overcome the difficulties in solving the optimization problem,the methods of fractional programming and successive convex approximation are then adopted to gradually transform the original problem into a series of tractable subproblems which are solved in an iterative manner. As shown in simulation results,by the joint designs in the spatial domain of UAV and the power domain of sensors,the proposed algorithm achieves a significant improvement of secrecy EE and rate.
文摘The first part of this report describes the data reduction of non-merohedrally twinned crystals measured on Bruker and Agilent area-detector diffractometers. The image frames of methyl-2-aminopyrazine-3-carboxylate were processed with APEX2 to furnish a set of overlapping diffraction indices that were used for solution and refinement. CrysAlisPRO was used for processing the frames of bis(diethyldicarbamato)nickel, which exists in monoclinic and tetragonal polymorphs, and in untwinned and twinned forms. In the second part, the crystal structure of [(3-formyl-4- hydroxyphenyl)methyl]triphenylphosphanium chloride was refined through the ‘HKLF 5'(based on a combined set of diffraction indices) and PLATON(based on one set of diffraction indices) routes to give identical outcomes because the amount of overlap of the twin domains is small. For the third part, in a proof-of-concept investigation, the diffraction pattern of untwinned and twinned 4-{(E)-(4-aminophenyl)diazenyl]phenylamine was recorded simultaneously in one run; the three domains could be indexed and the crystal structure satisfactorily refined. The refinement was identical to those derived from independent measurements; the crystal structure features two independent centrosymmetric molecules, one of which is ordered and the other whole-molecule-disordered. This two-in-one run opens up the possibility that two or more crystals having different atomic compositions can be measured simultaneously if their reciprocal lattices do not overlap significantly.
文摘With technological advancements in 6G and Internet of Things(IoT), the incorporation of Unmanned Aerial Vehicles (UAVs) and cellularnetworks has become a hot research topic. At present, the proficient evolution of 6G networks allows the UAVs to offer cost-effective and timelysolutions for real-time applications such as medicine, tracking, surveillance,etc. Energy efficiency, data collection, and route planning are crucial processesto improve the network communication. These processes are highly difficultowing to high mobility, presence of non-stationary links, dynamic topology,and energy-restricted UAVs. With this motivation, the current research paperpresents a novel Energy Aware Data Collection with Routing Planning for6G-enabled UAV communication (EADCRP-6G) technique. The goal of theproposed EADCRP-6G technique is to conduct energy-efficient cluster-baseddata collection and optimal route planning for 6G-enabled UAV networks.EADCRP-6G technique deploys Improved Red Deer Algorithm-based Clustering (IRDAC) technique to elect an optimal set of Cluster Heads (CH) andorganize these clusters. Besides, Artificial Fish Swarm-based Route Planning(AFSRP) technique is applied to choose an optimum set of routes for UAVcommunication in 6G networks. In order to validated whether the proposedEADCRP-6G technique enhances the performance, a series of simulationswas performed and the outcomes were investigated under different dimensions.The experimental results showcase that the proposed model outperformed allother existing models under different evaluation parameters.
基金This work was supported by the National Research Foundation of Korea(NRF)grant funded by the Korea government(MSIT)(No.2021R1F1A1063319).
文摘In recent times,sixth generation(6G)communication technologies have become a hot research topic because of maximum throughput and low delay services for mobile users.It encompasses several heterogeneous resource and communication standard in ensuring incessant availability of service.At the same time,the development of 6G enables the Unmanned Aerial Vehicles(UAVs)in offering cost and time-efficient solution to several applications like healthcare,surveillance,disaster management,etc.In UAV networks,energy efficiency and data collection are considered the major process for high quality network communication.But these procedures are found to be challenging because of maximum mobility,unstable links,dynamic topology,and energy restricted UAVs.These issues are solved by the use of artificial intelligence(AI)and energy efficient clustering techniques for UAVs in the 6G environment.With this inspiration,this work designs an artificial intelligence enabled cooperative cluster-based data collection technique for unmanned aerial vehicles(AECCDC-UAV)in 6G environment.The proposed AECCDC-UAV technique purposes for dividing the UAV network as to different clusters and allocate a cluster head(CH)to each cluster in such a way that the energy consumption(ECM)gets minimized.The presented AECCDC-UAV technique involves a quasi-oppositional shuffled shepherd optimization(QOSSO)algorithm for selecting the CHs and construct clusters.The QOSSO algorithm derives a fitness function involving three input parameters residual energy of UAVs,distance to neighboring UAVs,and degree of UAVs.The performance of the AECCDC-UAV technique is validated in many aspects and the obtained experimental values demonstration promising results over the recent state of art methods.
基金supported by National Key R&D Program of China (Grant No. 2021ZD0112803)National Natural Science Foundation of China (Grants No. 62122066, U20A20182, 61872274)
文摘With the rapid developments of Internet of Things(IoT)and proliferation of embedded devices,large volume of personal data are collected,which however,might carry massive private information about attributes that users do not want to share.Many privacy-preserving methods have been proposed to prevent privacy leakage by perturbing raw data or extracting task-oriented features at local devices.Unfortunately,they would suffer from significant privacy leakage and accuracy drop when applied to other tasks as they are designed and optimized for predefined tasks.In this paper,we propose a novel task-free privacy-preserving data collection method via adversarial representation learning,called TF-ARL,to protect private attributes specified by users while maintaining data utility for unknown downstream tasks.To this end,we first propose a privacy adversarial learning mechanism(PAL)to protect private attributes by optimizing the feature extractor to maximize the adversary’s prediction uncertainty on private attributes,and then design a conditional decoding mechanism(ConDec)to maintain data utility for downstream tasks by minimizing the conditional reconstruction error from the sanitized features.With the joint learning of PAL and ConDec,we can learn a privacy-aware feature extractor where the sanitized features maintain the discriminative information except privacy.Extensive experimental results on real-world datasets demonstrate the effectiveness of TF-ARL.
基金supported by Tianjin Municipal Information Industry Office (No. 082044012)
文摘Exploiting mobile elements (MEs) to accomplish data collection in wireless sensor networks (WSNs) can improve the energy efficiency of sensor nodes, and prolong network lifetime. However, it will lead to large data collection latency for the network, which is unacceptable for data-critical applications. In this paper, we address this problem by minimizing the traveling length of MEs. Our methods mainly consist of two steps: we first construct a virtual grid network and select the minimal stop point set (SPS) from it; then, we make optimal scheduling for the MEs based on the SPS in order to minimize their traveling length. Different implementations of genetic algorithm (GA) are used to solve the problem. Our methods are evaluated by extensive simulations. The results show that these methods can greatly reduce the traveling length of MEs, and decrease the data collection latency.
文摘In this paper we describe a system used to control,collect and process data in an 8 mm portable microwave radiometer scatterometer .We focus on hardware and software design of the system based on a PIC16F874 chip. The system has been successfully used in an 8 mm portable microwave radiometer scatterometer. Compared with other similar systems, the system modularization, miniaturization and intelligentization are improved so as to meet portable instrument requirements.
基金This paper was supported in part by Project funded by China Postdoctoral Science Foundation under Grant 2020M671552in part by Jiangsu Planned Projects for Postdoctoral Research Funds under Grant 2019K233+2 种基金in part by NUPTSF(NY220060)in part by the Opening Project of Jiangsu Key Laboratory of Data Science and Smart Software(No.2020DS301)in part by Natural Science Foundation of Jiangsu Province of China under Grant BK20191381.
文摘In the IoT(Internet of Things)system,the introduction of UAV(Unmanned Aerial Vehicle)as a new data collection platform can solve the problem that IoT devices are unable to transmit data over long distances due to the limitation of their battery energy.However,the unreasonable distribution of UAVs will still lead to the problem of the high total energy consumption of the system.In this work,to deal with the problem,a deployment model of a mobile edge computing(MEC)system based on multi-UAV is proposed.The goal of the model is to minimize the energy consumption of the system in the process of data transmission by optimizing the deployment of UAVs.The DEVIPSK(differential evolution algorithm with variable population size based on a mutation strategy pool initialized by K-Means)is proposed to solve the model.In DEVIPSK,the population is initialized by K-Means to obtain better initial positions of UAVs.Besides,considering the limitation of the fixed mutation strategy in the traditional evolutionary algorithm,a mutation strategy pool is used to update the positions of UAVs.The experimental results show the superiority of the DEVIPSK and provide guidance for the deployment of UAVs in the field of edge data collection in the IoT system.
文摘Traffic data collection is essential for performance assessment, safety improvement and road planning. While automated traffic data collection for highways is relatively mature, that for roundabouts is more challenging due to more complex traffic scenes, data specifications and vehicle behavior. In this paper, the authors propose an automated traffic data collection system dedicated to roundabout scenes. The proposed system has mainly four steps of processing. First, camera calibration is performed for roundabout traffic scenes with a novel circle-based calibration algorithm. Second, the system uses enhanced Mixture of Gaussian algorithm with shaking removal for video segmentation, which can tolerate repeated camera displacements and background movements. Then, Kalman filtering, Kemel-based tracking and overlap-based opti- mization are employed to track vehicles while they are occluded and to derive the complete vehicle trajectories. The resulting vehicle trajectory of each individual vehicle gives the position, size, shape and speed of the vehicle at each time moment. Finally, a data mining algorithm is used to automatically extract the interested traffic data from the vehicle trajectories. The overall traffic data collection system has been implemented in software and runs on regular PC. The total processing time for a 3-hour video is currently 6 h. The automated traffic data collection system can significantly reduce cost and improve efficiency compared to manual data collection. The extracted traffic data have been compared to accurate manual measurements for 29 videos recorded on 29 different days, and an accuracy of more than 90% has been achieved.
基金This work is supported by the National Key R&D Program of China under Grant No.2018YFB0505000the National Natural Science Foundation of China under Grant No.U1836115,No.61922045,No.U1836115 and No.61672295+2 种基金the Natural Science Foundation of Jiangsu Province under Grant No.BK20181408the State Key Laboratory of Cryptology Foundation,Guangxi Key Laboratory of Cryptography and Information Security No.GCIS201715the CICAEET fund,and the PAPD fund.
文摘With the rapid spread of smart sensors,data collection is becoming more and more important in Mobile Edge Networks(MENs).The collected data can be used in many applications based on the analysis results of these data by cloud computing.Nowadays,data collection schemes have been widely studied by researchers.However,most of the researches take the amount of collected data into consideration without thinking about the problem of privacy leakage of the collected data.In this paper,we propose an energy-efficient and anonymous data collection scheme for MENs to keep a balance between energy consumption and data privacy,in which the privacy information of senors is hidden during data communication.In addition,the residual energy of nodes is taken into consideration in this scheme in particular when it comes to the selection of the relay node.The security analysis shows that no privacy information of the source node and relay node is leaked to attackers.Moreover,the simulation results demonstrate that the proposed scheme is better than other schemes in aspects of lifetime and energy consumption.At the end of the simulation part,we present a qualitative analysis for the proposed scheme and some conventional protocols.It is noteworthy that the proposed scheme outperforms the existing protocols in terms of the above indicators.
基金MKE(the Ministry of Knowledge Economy),Korea,under the Convergence-ITRC(Convergence Infor mation Technology Research Center)support program(NIPA-2011-C6150-1101-0004)supervised by the NIPA(National IT Industry Pro-motion Agency)
文摘We suggest event collection protocol in a specific region where sensors are deployed to detect and collect events.In the traditional multi-hop routing in wireless sensor networks reporting events to a sink node or base-station will cause imbalanced energy consumption of static sensors.To solve this problem,we use mobile sink.In this paper,we study the design of efficiency routing protocol for supporting efficient data collecting in mobile sink wireless sensor networks(mWSNs).We suggest the following two main ideas.First,we use reactive protocol to cut off unnecessary delay.Mobile sink makes a path to access to sensor node.Second,we model mobile sink movement depending on data frequency,so we can reduce moving distance efficiently.We simulate this protocol and compare it with the traditional method.Simulation results show this protocol reduces distance significantly and is suitable for mWSNs with heavy traffic.
文摘<div style="text-align:justify;"> Due to its air superiority and high mobility, unmanned aerial vehicle (UAV) can obtain better line-of-sight (LoS) link transmission channel. Therefore, UAV assisted data collection for wireless sensor networks (WSNs) has become an important research direction. This paper intends to minimize the loss of WSNs for the robust data acquisition and communication assisted by UAV under the imperfect channel state information (CSI). On the premise of ensuring the completion of the communication task, we jointly optimize the wake-up schedule of SNs and the flight trajectory of the UAV, by considering the flight speed of the UAV and the sparse access of all sensor nodes (SNs) in WSN. Because the formulated optimization problem is a mixed integer nonconvex problem, we decompose the original problem into the efficient suboptimal solutions to overcome the difficulty of the optimization. Finally, the number of access node corresponding to the optimized operation time and access efficiency is induced for the entire WSN system efficiency improving. The simulation shows the performance gains of our proposed scheme and the influences of the system parameters are analyzed. </div>