Efficient desorption and reuse of collector from the flotation concentrate:A case study of scheelite

Flotation is the most common method to obtain concentrate through the selective adsorption of collectors on target minerals to make them hydrophobic and floatable.In the hydrometallurgy of concentrate,collectors adsorbed on concentrate can damage ion-exchange resin and increase the chemical oxygen demand(COD)value of wastewater.In this work,we proposed a new scheme,i.e.,desorbing the collectors from concentrate in ore dressing plant and reusing them in flotation flowsheet.Lead nitrate and benzohydroxamic acid(Pb-BHA)complex is a common collector in scheelite flotation.In this study,different physical(stirring or ultrasonic waves)and chemical(strong acid or alkali environment)methods for facilitating the desorption of Pb-BHA collector from scheelite concentrate were explored.Single-mineral desorption tests showed that under the condition of pulp pH 13 and ultrasonic treatment for 15 min,the highest desorption rates of Pb and BHA from the scheelite concentrate were 90.48%and 63.75%,respectively.Run-of-mine ore flotation tests revealed that the reuse of desorbed Pb and BHA reduced the collector dosage by 30%for BHA and 25%for Pb.The strong alkali environment broke the chemical bonds between Pb and BHA.The cavitation effect of ultrasonic waves effectively reduced the interaction intensity between Pb-BHA collector and scheelite surfaces.This method combining ultrasonic waves and strong alkali environment can effectively desorb the collectors from concentrate and provide“clean”scheelite concentrate for metallurgic plants;the reuse of desorbed collector in flotation flowsheet can reduce reagent cost for ore dressing plants.

Ultra-soft Desorption Assisted Mass Spectrometry using Picosecond Infrared Laser for the Detection of lons in the Liquid Surface

To identify the species in liquid surface using mass spectrometry,we must eliminate or reduce interferences during the vaporization or desorption of the species from the liquid surface.It is much more challenging to isolate the ionic,larger species from the liquid surface,because of the frangible structures and the higher solvation energies of those species.Here we demonstrate a new mass spectrometry in which the ionic species at the liquid surface can be desorbed with ultrasoft infrared picosecond laser pulses while the liquid surface is not breached.This laser desorption assisted mass spectrometry is not only a powerful tool to detect the fragile species but also promising to investigate vibrational energy transfer dynamics in the liquid surface.

Effects of Different Concentrations of Sulfate Ions on Carbonate Crude Oil Desorption:Experimental Analysis and Molecular Simulation

Low salinity water containing sulfate ions can significantly alter the surface wettability of carbonate rocks.Nevertheless,the impact of sulfate concentration on the desorption of oil film on the surface of carbonate rock is still unknown.This study examines the variations in the wettability of the surface of carbonate rocks in solutions containing varying amounts of sodium sulfate and pure water.The problem is addressed in the framework of molecular dynamics simulation(Material Studio software)and experiments.The experiment’s findings demonstrate that sodium sulfate can increase the rate at which oil moisture is turned into water moisture.The final contact angle is smaller than that of pure water.The results of the simulations show that many water molecules travel down the water channel under the influence of several powerful forces,including the electrostatic force,the van der Waals force and hydrogen bond,crowding out the oil molecules on the calcite’s surface and causing the oil film to separate.The relative concentration curve of water and oil molecules indicates that the separation rate of the oil film on the surface of calcite increases with the number of sulfate ions.

Quantum Tunneling Enhanced Hydrogen Desorption from Graphene Surface: Atomic versus Molecular Mechanism

We study the desorption mechanism of hydrogen isotopes from graphene surface using first-principles calculations,with focus on the effects of quantum tunneling.At low temperatures,quantum tunneling plays a dominant role in the desorption process of both hydrogen monomers and dimers.In the case of dimer desorption,two types of mechanisms,namely the traditional one-step desorption in the form of molecules(molecular mechanism),and the two-step desorption in the form of individual atoms(atomic mechanism),are studied and compared.For the ortho-dimers,the dominant desorption mechanism is found to switch from the molecular mechanism to the atomic mechanism above a critical temperature,which is∼300K and 200K for H and D,respectively.

Accelerating H^(*)desorption of hollow Mo_(2)C nanoreactor via in-situ grown carbon dots for electrocatalytic hydrogen evolution

Molybdenum carbide(Mo_(2)C)is a promising non-noble metal electrocatalyst with electronic structures similar to Pt for hydrogen evolution reaction(HER).However,strong H^(*)adsorption at the Mo sites hinders the improvement of HER performance.Here,we synthesized monodisperse hollow Mo_(2)C nanoreactors,in which the carbon dots(CD)were in situ formed onto the surface of Mo_(2)C through carburization reactions.According to finite element simulation and analysis,the CD@Mo_(2)C possesses better mesoscale diffusion properties than Mo_(2)C alone.The optimized CD@Mo_(2)C nanoreactor demonstrates superior HER performance in alkaline electrolyte with a low overpotential of 57 mV at 10 mA cm^(−2),which is better than most Mo_(2)C-based electrocatalysts.Moreover,CD@Mo_(2)C exhibits excellent electrochemical stability during 240 h,confirmed by operando Raman and X-ray diffraction(XRD).Density functional theory(DFT)calculations show that carbon dots cause the d-band center of CD@Mo_(2)C to shift away from Fermi level,promoting water dissociation and the desorption of H^(*).This study provides a reasonable strategy towards high-activity Mo-based HER eletrocatalysts by modulating the strength of Mo–H bonds.

Pore structure of low‑permeability coal and its deformation characteristics during the adsorption–desorption of CH4/N2

The pore structure of coal plays a key role in controlling the storage and migration of CH4/N2.The pore structure of coal is an important indicator to measure the gas extraction capability and the gas displacement efect of N2 injection.The deformation characteristic of coal during adsorption–desorption of CH4/N2 is an important factor afecting CH4 pumpability and N2 injectability.The pore structure characteristics of low-permeability coal were obtained by fuid intrusion method and photoelectric radiation technology.The multistage and connectivity of coal pores were analyzed.Subsequently,a simultaneous test experiment of CH4/N2 adsorption–desorption and coal deformation was carried out.The deformation characteristics of coal were clarifed and a coal strain model was constructed.Finally,the applicability of low-permeability coal to N2 injection for CH4 displacement technology was investigated.The results show that the micropores and transition pores of coal samples are relatively developed.The pore morphology of coal is dominated by semi-open pores.The pore structure of coal is highly complex and heterogeneous.Transition pores,mesopores and macropores of coal have good connectivity,while micropores have poor connectivity.Under constant triaxial stress,the adsorption capacity of the coal for CH4 is greater than that for N2,and the deformation capacity of the coal for CH4 adsorption is greater than that for N2 adsorption.The axial strain,circumferential strain,and volumetric strain during the entire process of CH4 and N2 adsorption/desorption in the coal can be divided into three stages.Coal adsorption–desorption deformation has the characteristics of anisotropy and gas-diference.A strain model for the adsorption–desorption of CH4/N2 from coal was established by considering the expansion stress of adsorbed gas on the coal matrix,the compression stress of free gas on the coal matrix,and the expansion stress of free gas on micropore fractures.N2 has good injectability in low-permeability coal seams and has the dual functions of improving coal seam permeability and enhancing gas fow,which can signifcantly improve the efectiveness of low-permeability coal seam gas control and promote the efcient utilization of gas resources.

Experimental and Numerical Research on Water Transport during Adsorption and Desorption in Cement-Based Materials

The durability of cement-based materials is related to water transport and storage in their pore network under different humidity conditions.To understand the mechanism and characteristics of water adsorption and desorption processes from the microscopic scale,this study introduces different points of view for the pore space model generation and numerical simulation of water transport by considering the“ink-bottle”effect.On the basis of the pore structure parameters(i.e.,pore size distribution and porosity)of cement paste and mortar with water-binder ratios of 0.3,0.4 and 0.5 obtained via mercury intrusion porosimetry,randomly formed 3D pore space models are generated using two-phase transformation on Gaussian random fields and verified via image analysis method of mathematical morphology.Considering the Kelvin-Laplace equation and the influence of“ink-bottle”pores,two numerical calculation scenarios based on mathematical morphology are proposed and applied to the generated model to simulate the adsorption-desorption process.The simulated adsorption and desorption curves are close to those of the experiment,verifying the effectiveness of the developed model and methods.The obtained results characterize water transport in cement-based materials during the variation of relative humidity and further explain the hysteresis effect due to“ink-bottle”pores from the microscopic scale.

Study of the Temperature-Programmed Desorption of Carbon Dioxide (CO2) on Zeolites X Modified with Bivalent Cations

Study of physisorbed and chemisorbed carbon dioxide (CO2) species was carried out on the NaX zeolite modified by cationic exchanges with bivalent cations (Ca2+ and Ba2+) by temperature-programmed desorption of CO2 (CO2-TPD). Others results were obtained by infrared to complete the study. The results of this research showed, in the physisorption region (213 - 473 K), that the cationic exchanges on NaX zeolite with bivalent cations increase slightly the interactions of CO2 molecule with adsorbents and/or cationic site. Indeed, the desorption energies of physisorbed CO2 obtained on the reference zeolite NaX (13.5 kJ·mol-1) are lower than that of exchanged zeolites E-CaX and E-BaX (15.77 and 15.17 kJ·mol-1 respectively). In the chemisorbed CO2 region (573 - 873 K), the desorption energies related to desorbed species (bidentate carbonates: CO32-) on the exchanged zeolites E-CaX and E-BaX are about 81 kJ·mol-1, higher than the desorbed species (bicarbonates: HCO32-) on the reference R-NaX (62 kJ·mol-1). In addition, the exchanged E-BaX zeolite develops the secondary adsorption sites corresponding to bicarbonates species with desorption energies of 35 kJ·mol-1 lower to desorption energies of bicarbonates noted on the reference zeolite NaX.

Desorption of Methylene Blue Adsorbed on Activated Carbon from Cocoa Pod Shell

Environmental protection has become a concern for the world. For this reason, the objective of this work is to remove methylene blue adsorbed on activated carbon. The coal used comes from cocoa pod shells. Before pyrolysis, the shells were ground, sieved and impregnated with orthophosphoric acid. Before desorption, the activated carbons were initially saturated with MB. These saturated coals were brought into contact with a sodium chloride (NaCl) solution and then stirred. The evolution of the resorbed MB concentration was monitored by spectrophotometry. The desorption tests showed a remarkable elimination from the first 10 minutes. The desorption kinetics comprises two phases: a rapid kinetics between 0 and 30 minutes and a slow kinetics between 30 and 60 minutes. The desorption of the dye reaches a concentration aqual to 0.84 mg/l at pH = 4 at temperature = 80°C. For modeling, the coefficient of the Langmuir II model is greater than or equal to O.9893. The model of Langmuir III is less than or equal to 0.9373. The Freundlich model coefficient is 0.9842 or less. The desorption is thefore carried out on energy-homogeneous adsorption sites and without any interaction between the adsorbed cations of the dye. Experimental parameters such as pH, temperature and concentration of sodium chloride (NaCl) solution influence the desorption of MB. And the model of Langmuir II describes well the process of desorption of the MB.

Effect of shaking time, ionic strength, temperature and pH value on desorption of Cr(III) adsorbed onto GMZ bentonite

The Cr（III） desorption experiments of Gaomiaozi （GMZ） bentonite in aqueous solutions were performed. The variables affecting the desorption behaviors, such as contact time, concentration of the desorbent, pH value of the solution, temperature and desorption isotherms, were investigated by the batch experiments. The results show that the adsorbed Cr（III） on GMZ bentonite can be easily extracted by the desorbent. Kinetics examination shows that desorption is slower than adsorption, and the desorption rate increases with time and reaches the equilibrium after 3 h. The final desorption ratios of Cr（III） are 89.4%, 56.5%and 77.2%in the desorption solution with 0.1 mol/L HCl, 1 mol/L NaCl, and 1 mol/L CaCl2, respectively, and the concentration can promote the desorption progress. Furthermore, the results of successive regeneration cycles indicate that the bentonite has a good regeneration ability and reusability. The pH value is an important factor in the Cr（III） desorption from the GMZ bentonite. The results of adsorption and desorption isotherms show that both adsorption and desorption isotherms are consistent with the Freundlich equation. The comparison of adsorption and desorption isotherms implies that the adsorption/desorption hysteresis is negligible and the transport of Cr（III） in bentonite can be described by a reversible adsorption process.

Study on Enhancement of PCBs Desorption in Soil by Surfactants

[Objective]The aim of this paper was to provide theoretical basis for study on enhancement of surfactants to desorption of PCBs from soil. [Method]The desorption effects of surfactants SDBs,Tween 80,HTAB on PCBs were studied as well as their distribution in water and soil. Effects of rationing on desorption of PCBs were also analyzed. [Result]The potential of single surfactant to enhance the desorption of PCBs from soil in order was Tween 80 SDBS HTAB. Three surfactants were largely adsorbed on soil and the sorption followed HTABTween 80SDBS. The desorption of PCBs increased significantly and linearly with the increase of aqueous micelle concentration of surfactants. [Conclusion]Enhancing effect of three surfactants on PCBs desorption were obtained,which will provide theoretical basis for further analyzing.

Hydrogen desorption kinetics mechanism of Mg-Ni hydride under isothermal and non-isothermal conditions

The Mg-Ni hydride was prepared by hydriding combustion synthesis under a high magnetic field. The dehydriding kinetics of the hydrides was measured under the isothermal and non-isothermal conditions. A model was applied to analyzing the kinetics behavior of Mg-Ni hydride. The calculation results show that the theoretical value and the experimental data can reach a good agreement, especially in the case of non-isothermal dehydriding. The rate-controlling step is the diffusion of hydrogen atoms in the solid solution. The sample prepared under magnetic field of 6 T under the isothermal condition can reach the best performance. The similar tendency was observed under the non-isothermal condition and the reason was discussed.

Study on the Effects of Polyacrylamide on Phosphorus Adsorption and Desorption Characteristics of Soil Aggregates

[Objective]The research aimed to provide scientific reference for reasonable utilization of polyacrylamide(PAM).[Method]After PAM treatment,the soil aggregates were classified through dry sieve analysis and the adsorption capacity and desorption capacity of all soil aggregates to phosphorus at different phosphorus concentrations were analyzed.[Result] The phosphorus adsorption and desorption of soil sample treated by PAM declined. The amount of phosphorus adsorption increased with the increase of phosphorus concentration and this increase was fast in low phosphorus concentration area but slow in high phosphorus concentration area.At different phosphorus concentrations,adsorption showed a へ shape changing trend.The phosphorus adsorption was related to phosphorus concentration and the 2-3 mm aggregate had the highest desorption rate while 0.1-0.25 mm aggregate and 0.45-1 mm aggregate had lowest desorption rate.[Conclusion]The PAM treatment generated significant influence on phosphorus adsorption and analytic features of aggregate in all size fractions.

Influence Factors on Particle Growth for On-line Aerosol Matrix-assisted Laser Desorption/Ionization Time-of-flight Mass Spectrometry

An evaporation/condensation flow cell was developed and interfaced with the matrix-assisted laser desorption/ionization （MALDI） time-of-flight mass spectrometer for on-line bioaerosol detection and characterization, which allows matrix addition by condensation onto the laboratory-generated bioaerosol particles. The final coated particle exiting from the con- denser is then introduced into the aerodynamic particle sizer spectrometer or home-built aerosol laser time-of-flight mass spectrometer, and its aerodynamic size directly effects on the matrix-to-analyte molar ratio, which is very important for MALDI technique. In order to observe the protonated analyte molecular ion, and then determine the classification of bi- ological aerosols, the matrix-to-analyte molar ratio must be appropriate. Four experimental parameters, including the temperature of the heated reservoir, the initial particle size, its number concentration, and the matrix material, were tested experimentally to analyze their influences on the final particle size. This technique represents an on-line system of detection that has the potential to provide rapid and reliable identification of airborne biological aerosols.

Adsorption and Desorption Characteristics of Cadmium and Lead in Typical Paddy Soils of Jiangxi Province and Its Environmental Risk Assessment

[Objective] This study aimed to investigate the adsorption and desorption characteristics of cadmium and lead in typical paddy soils of Jiangxi Province. [Method] Gleyed paddy soil and waterloggogenic paddy soil were collected from Jiangxi Province and used as experimental materials to investigate single and com- petitive adsorption and desorption behaviors of cadmium and lead by batch equilib- rium method. The environmental risk of the presence of cadmium and lead in paddy soils was assessed using distribution coefficients. [Result] Under equal ratio condi- tions, the adsorption capacity of lead by two types of paddy soils was higher than that of cadmium, and the adsorption rate in waterloggogenic paddy soil was higher than that in gleyed paddy soil. The desorption capacity of cadmium by two types of paddy soils was higher than that of lead, and the desorption rate in gleyed paddy soil was higher than that in waterloggogenic paddy soil. Under competitive condi- tions, the adsorption capacity of cadmium and lead by paddy soils was significantly reduced compared with single ion system, while the desorption rate was remarkably improved. The potential environmental risk of cadmium contamination was greater than that of lead in paddy soils. Moreover, environmental risks of cadmium and lead were reduced with the increase of pH, which increased significantly under the coex- istence state. [Conclusion] In the coexistence of cadmium and lead, cadmium con- tamination should be controlled and avoided compared with lead contamination in paddy soils.

Characteristics and applications of gas desorption with excavation disturbances in coal mining

According to the deficiency of experiment system for gas adsorption and desorption in coal mass, a large scale experiment system is developed independently by researchers. This experiment system is composed of primary and auxiliary boxes, power transmission system, mining system, loading system, gas charging system, data monitoring and intelligent acquisition system. The maximum experiment coal consumption is 1200 kg, the mining system is developed to conduct experiment for gas desorption under excavating disturbance, and the plane-charging cribriform ventilation device is developed to realize uniform ventilation for experiment coal sample, which is accord with the actual gas source situation of coal bed. The desorption characteristics of gas in coal are experimentally studied under the conditions of nature and mining using the experiment system. The results show that, compare with nature condition, the permeability of coal and the velocity of gas desorption could significantly increase under the influence of coal pressure relief and destruction caused by mining, and the degree of gas desorption could somewhat increase too. Finally, pressure relief gas extraction of current seam and adjacent seams after mining in a certain coal mine of Yangquan mining area are introduced, and the gas desorption experiment results is verified by analyzing the effect of gas extraction.

Adsorption and Desorption of Natural Zeolite on NH_4^+

The adsorption and desorption kinetic of natural zeolite on NH4＋ was stud-ied by lab analysis. The results showed that the adsorption and desorption kinetic of natural zeolite on NH4＋ coincided with the first-order kinetics, modified Freundlich equation, parabolic diffusion model, and heterogeneous diffusion model. The desorp-tion of the adsorbed NH4＋ was far rapider than the adsorption, which can be fin-ished within 60 min.

Research on Reliability of Desorption Indexes of Drilling Cuttings(K_(1)andΔh_(2)):A Case-Based on Pingdingshan Mining Region,China

To accurately predict the risk of coal and gas outburst and evaluate the reliability of desorption indexes of drilling cuttings(K_(1) andΔh_(2))in No.16 coal seam of Pingmei No.12 coal mine,two sets of coal samples were selected from the target coal seams for proximate analyses,methane adsorption/desorption tests,and desorption indexes of drilling cuttings tests.The results indicated that the desorption volume in the initial stage of desorption is large,and increases slowly in the later stage.The methane desorption volume of PMD1 and PMD2 coal samples accounts for 15.14%-18.09%and 15.72%-18.17%respectively in the first 1 min,and 43.92%-48.55%and 41.87%-52.25%respectively in the first 10 min in the 120 min desorption tests.Both K_(1) andΔh_(2) present power function relationships with methane pressure.Similarly,the power function relationships also can be found between the initial desorption characteristics(Q1 and Q4-5)and the methane pressure.Finally,the average relative error between the measured value and the calculated value of Q1 based on K_(1) is less than that of Q4-5 based onΔh_(2),which indicates that K_(1) is a more reliable index thanΔh_(2) to predict the risk of coal and gas outburst in the No.16 coal seam of Pingmei No.12 coal mine.

Effect of dissolved organic matter on adsorption and desorption of mercury by soils

Effects of dissolved organic matter (DOM) on adsorption and desorption of Hg were investigated in two kinds of soils, Xanthi-Udic Ferralosols (XUF) and Typic Purpli-Udic Cambosols (TPUC). The DOM was obtained from humus soil (DOMH), rice straw (DOMR), and pig manure (DOMP). The presence of DOM obviously reduced Hg maximum adsorption capacity with up to 40% decreases over the control, being an order of DOMH (250.00 mg/kg)< DOMR (303.03 mg/kg) < DOMP (322.58 mg/kg) < CK (control 416.67 mg/kg) for the...

Adsorption/desorption behavior between a novel amphoteric granular lignin adsorbent and reactive red K-3B in aqueous solutions

A novel amphoteric granular lignin adsorbent(AGLA) was prepared using magnesium lignosulfonate as a raw material which was provided by a straw sulfite pulp mill in Guangdong Province, China. A reactive dye(red K-3B) was used as an adsorbate to investigate the adsorption behavior by static and mobile ways. The removal of reactive red K-3B was found to be initially pH and concentration dependent. Moreover, an increase of solution temperature ranging from 5℃ to 60℃ helped to enhance the rate of intraparticle diffusion of adsorbate and changes in the size of the pores of the adsorbent and thus to reduce the adsorption time. The total breakthrough adsorption capacity was 531 mg/g, and the saturated adsorption capacity was 560 mg/g, which prevailed over the activated carbons evidently. The reactive red K-3B adsorbed on AGLA could be recovered with a mixture of alcohol, NaCl and HCl aqueous solutions. The recovery percentage could reach 92.4%.