Polybenzoxazine/organosilicon composites with low dielectric constant and dielectric loss

The evolution of electronic communication technology raises higher requirements for low dielectric constant(low-k)materials.For this,a benzoxazine functional organosilicon(HP-aptes)with dense Si—O—Si crosslinking networks and large sterically hindered tert-butyl groups was prepared by the sol–gel method.Then,a series of polybenzoxazine composites(PPHP)were prepared from intrinsically low dielectric constant bis-functional benzoxazine monomer(P-aptmds)and HP-aptes.The double crosslinking networks of polybenzoxazine and organosilicon further increased the crosslinking density and decreased the dipole density of composites,which endowed the composites with enhanced low-k properties.When the content of HP-aptes is 30%(mass),the crosslinking density was 2.05×10^(-3)mol·cm^(-3),while that of PP-aptmds was 3.31×10^(-3)mol·cm^(-3).In addition,the dielectric constant and dielectric loss of PPHP composite at 1 MHz could reach 2.61 and 0.0056,respectively.

Study of Structural, Optical, Electrical and Dielectric Properties of Gd-Doped ZnO Composites Synthesized by Solid State Reaction Method

In this manuscript, we are reporting structural, bonding, optical, dielectric, and electrical properties of Gd-doped ZnO composite samples (Zn1−xGdxO, x = 0, 0.05, 0.10) prepared by solid-state reaction method. XRD spectra confirm the wurtzite hexagonal phase with a grain size distribution of 42 - 47 nm. The FT-IR spectra confirm bonding behavior like Zn-O, O=C=O, and O-H stretching modes. FESEM micrographs show that the grains of crystallites possess nearly spherical morphology. Optical absorption spectra confirm that the optical band gap decreases systematically from 3.19 eV to 3.15 eV for x = 0.0 to x = 0.10 samples. For all samples, PL spectra exhibited near-band emission, blue emission, and green emission peaks. The dielectric constant decreases as the applied frequency increases. Hall effect results show that with increasing doping concentration of Gd, mobility and resistivity increase while bulk concentration decreases. Current-Voltage study shows that current increases when temperature is increased. Rare earth-doped ZnO is potential material used for optoelectronics and spintronics device applications. Properties of Gd-doped ZnO are studied by various research groups, but dielectric studies are limitedly reported. Therefore, the present research work aims to study the change of electrical, optical, and dielectric properties of Gd-doped ZnO for device applications.

Synthesis and Characterization of SiCOF/a-C∶F Double-Layer Films with Low Dielectric Constant for Copper Interconnects~*

A novel double-layer film of SiCOF/a-C ： F with a low dielectric constant is deposited using a PECVD system. The chemical structure of the film is characterized with Fourier transform infrared spectroscopy （FTIR）. The measurements of the film refractive index reveal that the optical frequency dielectric constant （n^2） of the film is almost constant as a function of air exposure time, however, with increasing annealing temperature, the value of n^2 for the film decreases. Possible mechanisms are discussed in detail. The analysis of SIMS profiles for the metal-insulator-silicon structures reveal that in the Al/a-C ： F/Si structure,the annealing causes a more rapid diffusion of F in AI in comparison with C, but there is no obvious difference in Si. In addition, no recognizable verge exists between SiCOF and a-C ： F films,and the SiCOF film acts as a barrier against the diffusion of carbon into the aluminum layer.

Plasma-assisted ammonia synthesis in a packed-bed dielectric barrier discharge reactor:roles of dielectric constant and thermal conductivity of packing materials

In this article,plasma-assisted NH;synthesis directly from N;and H;over packing materials with different dielectric constants(BaTiO_(2),TiO_(2) and SiO_(2))and thermal conductivities(Be O,Al N and Al_(2)O_(2))at room temperature and atmospheric pressure is reported.The higher dielectric constant and thermal conductivity of packing material are found to be the key parameters in enhancing the NH;synthesis performance.The NH;concentration of 1344 ppm is achieved in the presence of BaTiO_(2),which is 106%higher than that of SiO_(2),at the specific input energy(SIE)of 5.4 k J·l^(-1).The presence of materials with higher dielectric constant,i.e.BaTiO_(2) and TiO_(2)in this work,would contribute to the increase of electron energy and energy injected to plasma,which is conductive to the generation of chemically active species by electron-impact reactions.Therefore,the employment of packing materials with higher dielectric constant has proved to be beneficial for NH;synthesis.Compared to that of Al_(2)O_(3),the presence of Be O and Al N yields 31.0%and 16.9%improvement in NH;concentration,respectively,at the SIE of5.4 k J·l^(-1).The results of IR imaging show that the addition of Be O decreases the surface temperature of the packed region by 20.5%to 70.3℃ and results in an extension of entropy increment compared to that of Al_(2)O_(3),at the SIE of 5.4 k J·l^(-1).The results indicate that the presence of materials with higher thermal conductivity is beneficial for NH;synthesis,which has been confirmed by the lower surface temperature and higher entropy increment of the packed region.In addition,when SIE is higher than the optimal value,further increasing SIE would lead to the decrease of energy efficiency,which would be related to the exacerbation in reverse reaction of NH;formation reactions.

Dynamic characteristics of charging effects on the dielectric constant due to E-beam irradiation:a numerical simulation

A series of synthetic variations of material intrinsic properties always come with charging phenomena due to electron beam irradiation.The effects of charging on the dielectric constant will influence the charging dynamic in return.In this paper,we propose a numerical simulation for investigating the dynamic characteristics of charging effects on the dielectric constant due to electron beam irradiation.The scattering process between electrons and atoms is calculated considering elastic and inelastic collisions via the Rutherford model and the fast secondary electron model,respectively.Internal charge drift due to E-field,density gradient caused diffusion,charges trap by material defect,free electron and hole neutralization,and variation in the internal dielectric constant are considered when simulating the transport process.The dynamics of electron and hole distributions and charging states are demonstrated during E-beam irradiation.As a function of material nonlinear susceptibility and primary energy,the dynamics of charging states and dielectric constants are then presented in the charging process.It is found that the variation in the internal dielectric constant is more with respect to the depth and irradiation time.Material with a larger nonlinear susceptibility corresponds a faster charging enhancement.In addition,the effective dielectric constant and the surface potential have a linear relationship in the charging balance.Nevertheless,with shrinking charging affect range,the situation with a higher energy primary electron comes with less dielectric constant variation.The proposed numerical simulation mode of the charging process and the results presented in this study offer a comprehensive insight into the complicated charging phenomena in electron irradiation related fields.

Fabrication of BaTiO3/Epoxy Composites Exhibiting Large Dielectric Constant, Low Dielectric Loss and High Flexural Strength

BaTiO3/epoxy composites consisting of two three-dimensionally interpenetrating networks of BaTiO3 and epoxy phases were prepared using a new approach. The BaTiO3/epoxy composites exhibit a colossal dielectric constant, low dielectric loss and high flexural strength. In the BaTiO3 networks, chemically bonded grain boundaries between neighboring BaTiO3 grains were established, and they are responsible for the colossal dielectric constant and high flexural strength of the BaTiO3/epoxy composites. Furthermore, unlike the conventional ceramic/polymer composites, this approach also makes high loadings of BaTiO3 contents possible for the BaTiO3/epoxy composites without compromising their high flexural strength.

Impact of Native Defects in the High Dielectric Constant Oxide HfSiO_4 on MOS Device Performance

Native dejects in HfSiO4 are investigated by first principles calculations. Transition levels of native detects can be accurately described by employing the nonlocal HSE06 hybrid functional. This methodology overcomes the band gap problem in traditional functionals. By band alignments among the Si, GaAs and HfSiO4. we are able to determine the position of defect levels in Si and GaAs relative to the HfSiO4 band gap. We evaluate the. possibility of these defects acting as fixed charge. Native defects lead to the change of valence and conduction band offsets. Gate leakage current is evaluated by the band offset. In addition, we also investigate diffusions of native defects, and discuss how they affect the MOS device performance.

Determination of Water Colltent in Clayey Red Soil Using Techniques Based on Measurement of Dielectric Constant

Two time-domain reflectometry (TDR) systems and a new impedance measuring instrument, Thetaprobe,which are based on determination of soil dielectric constant, were used to measure water content of clayeyred soil to eraluate the accuracy of these instruments. The results indicated that these instruments shouldbe carefUlly re-calibrated before being applied in clayey red soil. With a new calibration curve fed into one ofthe TDR systems tested, nase system, the measured data compared well with tho8e by standard oven-dryingmethod.

Dielectric constant predictions for energetic materials using quantum calculations

The dielectric constant(DC)is one of the key properties for detection of threat materials such as Improvised Explosive Devices(IEDs).In the present paper,the density functional theory(DFT)as well as ab-initio approaches are used to explore effective methods to predict dielectric constants of a series of 12 energetic materials(EMs)for which experimental data needed to experimentally determine the dielectric constant(refractive indices)are available.These include military grades energetic materials,nitro and peroxide compounds,and the widely used nitroglycerin.Ab-initio and DFT calculations are conducted.In order to calculate dielectric constant values of materials,potential DFT functional combined with basis sets are considered for testing.Accuracy of the calculations are compared to experimental data listed in the scientific literature,and time required for calculations are both evaluated and discussed.The best functional/basis set combinations among those tested are CAM-B3LYP and AUG-ccpVDZm,which provide great results,with accuracy deviations below 5%when calculated results are compared to experimental data.

Effective dielectric constant model of electromagnetic backscattering from stratified air–sea surface film–sea water medium

Studies of surface film medium on the sea surface are carried out in this paper for developing the technology to automatically detect and classify sea surface films, and an effective dielectric constant model of electromagnetic backscattering from a stratified air–ocean interface. Numerical results of the new model show the characteristics of effective dielectric constants for the air–sea surface film–sea water medium as follows. The effective dielectric constants decrease with increasing relative dielectric constants of the sea surface films. The effective dielectric constants decrease in horizontal polarization（abbr. HH polarization） and increase in VV vertical polarization（abbr. VV polarization） with increasing radar incident angle. Effective dielectric constants vary with relative sea surface film thickness as a cosinusoidal function of sea surface film thickness. Effective dielectric constant of VV polarization is larger than that of HH polarization. Two potential applications are found with our model, i.e., the retrieval of dielectric constants from the sea surface film, and the film thickness retrieval with our model. Our model has a highly significant influence on improving the technology related to the remote sensing of sea surface films.

Transmission spectra characteristics of 1D photonic crystals with complex dielectric constant

The characteristics of photonic forbidden bands, transmission gain and absorption of one-dimensional （ID） dual-periodical photonic crystals （PC） with a complex dielectric layer were studied by using the optical transfer matrix （TM） method. The results show that the photonic band gap （PBG） of this structure is enlarged and many transmission resonance peaks appear in PBG. Large transmission gain for transmission peaks is obtained if the imaginary part of dielectric constant is negative. With the increase of the absolute value of the imaginary part, the transmission gain increases firstly and the transmittance gain gets to an apex. The imaginary parts of dielectric constant corresponding to transmission gain apex are different according to wavelength. However, the transmission ratio of resonance peaks is less than 1 if the imagi- nary part of dielectric constant is positive. The properties might be used to design multi-narrow-channel band filters and optical amplification devices synchronously.

Study of the behaviour of the dielectric constant in Cu,Fe:BaTiO_3

In this work we study the behaviour of the dielectric constant of BaTiO3 single crystals doped with Cu and Fe for different ion percentages, particularly, the influence of these hetemvalent substitutions on the ferroelectric-paraelectric phase transition whose temperature is found at Tc=120℃ for pure samples. The dielectric constant e in terms of temperature shows that the Curie temperature decreases when the quantity of impurities increases and presents a broadening and flattering of the maximum oft（T） within higher values, with the transition becoming more and more diffuse. It is interesting to have a material with very high permittivity （high-k） because of its capacity to store an important quantity of electric charges. The t anisotropy and the Curie-Weiss law are also verified with a good ratio between the slopes ofε^-l（T） from both sides of the transition, leading to a Curie constant： C= 13 × 10^4 K for BaTiO3：1.6%Fe in the polar phase. BaTiO3 is a displacive ferroelectric going through a first-order phase transition. The substitutions have an effect on the dynamics of the perovskite lattice. They induce charges transfer to Ti and a diminution of elastic forces in BaTiO3. Then we discuss the transition but on the nature of the material. fact that the maximum of permittivity does not depend on the phase

Helium Plasma Damage of Low-k Carbon Doped Silica Film:the Effect of Si Dangling Bonds on the Dielectric Constant

The low-k carbon doped silica film has been modified by radio frequency helium plasma at 5 Pa pressure and 80 W power with subsequent XPS, FTIR and optical emission spec- troscopy analysis. XPS data indicate that helium ions have broken Si-C bonds, leading to Si-C scission with C（1s） lost seriously. The Si（2p）, O（ls）, peak obviously shifted to higher binding en- ergies, indicating an increasingly oxidized Si（2p）. FTIR data also show that the silanol formation increased with longer exposure time up to a week. Contrarily, the CHa stretch, Si-C stretching bond and the ratio of the Si-O-Si cage and Si-O-Si network peak sharply decreased upon exposure to helium plasma. The OES result indicates that monovalent helium ions in plasma play a key role in damaging carbon doped silica film. So it can be concluded that the monovalent helium ions besides VUV photons can break the weak Si-C bonds to create Si dangling bonds and free methyl radicals, and the latter easily reacts with O_2 from the atmosphere to generate CO_2 and H_2O. The bonds change is due to the Si dangling bonds combining with H_2O, thereby, increasing the dielectric constant k value.

Liquid Phase Sintering (LPS) and Dielectric Constant of α-Silicon Nitride Ceramic

The spark plasma sintering （SPS） was applied to prepare α-Si3 N4 ceramics of different densities with magnesia, silicon dioxide, alumina as the sintering aids. The mechanism of liquid phase sintering （LPS） wus discussed and the factors influencing the density of the prepared samples were analyzed. The dielectric constant of sintered samples was tested. The experimental results show that the density can be controlled from 2.48 g/ cm^3 to 3.09 g/ cm^3 while the content of the sintering aids and the sintering temperature alter and the dielectric constant is closely dependent on the density of obtained samples.

A Group Contribution Method for the Correlation of Static Dielectric Constant of Ionic Liquids

Static dielectric constant is a key parameter to estimate the electro-viscous effect which plays important roles in the flow and convective heat transfer of fluids with ions in microfluidic devices such as micro reactors and heat exchangers.A group contribution method based on 27 groups is developed for the correlation of static dielectric constant of ionic liquids in this paper.The ionic liquids considered include imidazolium,pyridinium,pyrrolidinium,alkylammonium,alkylsulfonium,morpholinium and piperidinium cations and various anions.The data collected cover the temperature ranges of 278.15-343.15 K and static dielectric constant ranges of 9.4-85.6.The results of the method show a satisfactory agreement with the literature data with an average absolute relative deviation of 7.41%,which is generally of the same order of the experimental data accuracy.The method proposed in this paper provides a simple but reliable approach for the prediction of static dielectric constant of ionic liquids at different temperatures.

Nonlinear parametric interactions in ion-implanted semiconductor plasmas having strain-dependent dielectric constants

We report nonlinear parametric interactions using a hydrodynamic model of ion-implanted semiconductor plasmas having strain-dependent dielectric constants（SDDC）. High-dielectric-constant materials are technologically important because of their nonlinear properties. We find that the third-order susceptibility varies in the range 10^-14--10^-12m^2·V^-2 for ion-implanted semiconductor plasmas, which is in good agreement with previous results. It is found that the presence of SDDC in ion-implanted semiconductor plasma modifies the characteristic properties of the material.

Chemical Bonds and Dielectric Constants of REM（RE＝Rare Earth，M＝N，P，As，Sb）Crystals

By using Pillips and van Vechten theory, the chemical bond parameters and dielectric constants of REM (RE=rare earth,M=N,P,As,Sb) crystals were calculated.The values calculated of dielectric constants agree with the experimental values.

Local Dielectric Constant of the Solvent Shell Surrounding Ethyl Acetoacetate in Cosolvent-Modified Supercritical Carbon Dioxide

The enol contents and equilibrium constants for keto-enol tautomerism of ethyl acetoacetate in supercritical (SC) CO2 with and without cosolvent ethanol and in various liquid solvents were investigated by UV spectroscopy. The local dielectric constant about the solute in SC CO2/ethanol system was obtained through the correlation between Gibbs free energy of tautomerism and Onsager-Kirkwood solvent quantity. The great difference between local dielectric constant and that calculated from homogeneous dielectric medium theory suggests clustering of the cosolvent around the solute.

A Decisive Study on Dielectric Response of Bi2O3/Polystyrene &Bi2O3/PVDF Composite as Flexible Electrodes for Energy Storage

In this manuscript a comparative study on Bi2O3/polystyrene and Bi2O3/PVDF composites has been executed via analysis of structural, bonding, surface morphology and dielectric response of composites for energy storage. The composites have been synthesized using solution cast method by varying concentrations of Bi2O3 (BO = 1 - 5 mw%) into polystyrene (PS) and polyvinylidene fluoride (PVDF) polymers respectively. X-ray diffraction confirms the generation of crystallinity, Fourier transform infrared (FT-IR) spectroscopy confirms bonding behavior and scanning electron microscopy (SEM) confirms uniform distribution of Bi2O3 (BO) in PS and PVDF polymers. Impedance spectroscopy has been employed for determination of dielectric response of the fabricated composites. The dielectric constant has been found to be increased as 1.4 times of pristine PS to BO5%PS95% composites and 1.8 times of pristine PVDF to BO5%PVDF95% composites respectively. These high dielectric composite electrodes are useful for flexible energy storage devices.

Effect of Cu ion substitution on structural and dielectric properties of Ni-Zn ferrites

A series of Cu-substituted Ni_(0.5-x)Cu_xZn_(0.5)Fe_2O_4(x=0.12,0.16,0.20,0.24 and 0.28) spinel ferrites were prepared by conventional ceramic method to investigate the effects of Cu compositional variation on the structure and dielectric properties.XRD patterns demonstrate that all the samples are crystallized in single-phase cubic spinel structure and the lattice constant increases with increasing Cu content.White grains observed by SEM are Cu-rich phase.The dielectric constant versus frequency curve displays a normal dielectric behavior of spinel ferrites.While the frequency dependence of dielectric loss tangent is found to be abnormal,exhibiting a peak at certain frequency for all Cu-substituted Ni-Zn ferrites.A maximum of the resistivity is observed at x=0.2 due to the decrease of hopping electrons between Fe^(2+) and Fe^(3+) in per unit volume,which is in contrast with the Cu content dependence of dielectric constant and dielectric loss.