Optimization of Center of Gravity Position and Anti-Wave Plate Angle of Amphibious Unmanned Vehicle Based on Orthogonal Experimental Method

When the amphibious vehicle navigates in water,the angle of the anti-wave plate and the position of the center of gravity greatly influence the navigation characteristics.In the relevant research on reducing the navigation resistance of amphibious vehicles by adjusting the angle of the anti-wave plate,there is a lack of scientific selection of parameters and reasonable research of simulation results by using mathematical methods,and the influence of the center of gravity position on navigation characteristics is not considered at the same time.To study the influence of the combinations of the angle of the anti-wave plate and the position of the center of gravity on the resistance reduction characteristics,a numerical calculation model of the amphibious unmanned vehicle was established by using the theory of computational fluid dynamics,and the experimental data verified the correctness of the numerical model.Based on this numerical model,the navigation characteristics of the amphibious unmanned vehicle were studied when the center of gravity was located at different positions,and the orthogonal experimental design method was used to optimize the parameters of the angle of the anti-wave plate and the position of the center of gravity.The results show that through the parameter optimization analysis based on the orthogonal experimental method,the combination of the optimal angle of the anti-wave plate and the position of the center of gravity is obtained.And the numerical simulation result of resistance is consistent with the predicted optimal solution.Compared with the maximum navigational resistance,the parameter optimization reduces the navigational resistance of the amphibious unmanned vehicle by 24%.

A Spider Monkey Optimization Algorithm Combining Opposition-Based Learning and Orthogonal Experimental Design

As a new bionic algorithm,Spider Monkey Optimization(SMO)has been widely used in various complex optimization problems in recent years.However,the new space exploration power of SMO is limited and the diversity of the population in SMO is not abundant.Thus,this paper focuses on how to reconstruct SMO to improve its performance,and a novel spider monkey optimization algorithm with opposition-based learning and orthogonal experimental design(SMO^(3))is developed.A position updatingmethod based on the historical optimal domain and particle swarmfor Local Leader Phase(LLP)andGlobal Leader Phase(GLP)is presented to improve the diversity of the population of SMO.Moreover,an opposition-based learning strategy based on self-extremum is proposed to avoid suffering from premature convergence and getting stuck at locally optimal values.Also,a local worst individual elimination method based on orthogonal experimental design is used for helping the SMO algorithm eliminate the poor individuals in time.Furthermore,an extended SMO^(3)named CSMO^(3)is investigated to deal with constrained optimization problems.The proposed algorithm is applied to both unconstrained and constrained functions which include the CEC2006 benchmark set and three engineering problems.Experimental results show that the performance of the proposed algorithm is better than three well-known SMO algorithms and other evolutionary algorithms in unconstrained and constrained problems.

Optimization of extraction of polyphenols from pomegranate peel by orthogonal experiment design and antioxidant activity

The aim of this study was to investigate the extraction process and antioxidant activity of polyphenols from Yunnan Mengzi pomegranate peel.Single factor and orthogonal test were used as optimize the extract rate(ER)of polyphenols from pomegranate peel(PGP).The polyphenols antioxidant activity was evaluated by DPPH·,·OH and total reducing ability,and compared with that of Vc.The optimum extraction conditions of polyphenols were as follows:ethanol concentration of 50%,liquid-solid ratio of 50:1,extraction temperature of 90°C,extraction for 4 h.Under these conditions,the ER of polyphenols from GPG was 8.15%.The results showed that the scavenging effects of polyphenols and Vc on DPPH·,·OH increased with increasing concentration,and the scavenging effect of polyphenols on DPPH·was higher than Vc in rang of 0.1-1.6µg/mL.When the concentration is greater than 0.6µg/mL,the scavenging effects of plyphenols on·OH is higher than Vc.The total reducing ability of polyphenols from PGP improved with the increase of concentration,and when the concentration was 8µg/mL,the total reducing ability was 114 U/mL.

An Orthogonal Experiment of Papain-Assisted Extraction of Polysaccharides from Agrocybe aegirit

[Objective] This study aimed to explore optimum conditions for papain-as- sisted extraction of polysaccharides from Agrocybe aegirit. [Method] Because enzyme is capable of destroying organizational structure of cells, papain was selected to cat- alyze cells to let polysaccharides out. An orthogonal experiment was carried out to investigate the effects of hydrolysis temperature, hydrolysis time, enzyme concentra- tion and solid to liquid ratio on extraction of polysaccharides from A. aegirit. [Result] Through the orthogonal experiment, the optimum papain-assisted extraction conditions were obtained： hydrolysis temperature, 45 ℃; hydrolysis time, 2 h; enzyme concen- tration 2%; solid to liquid ratio, 1：80. [Conclusion] This study will provide a reference for extraction of polysaccharides from A. aegirit.

Orthogonal experiment design of EMI of security monitoring system in coal mines

Security monitoring system of coal mines is indispensable to ensure the safe and efficient production of colliery. Due to the special and narrow underground field of the coal mine, the electromagnetic interference can cause a series of misstatements and false positives on the monitoring system, which will severely hamper the safe production of coal industry. In this paper, first, the frequency characteristics of the interference source on the power line are extracted when equipment runs normally. Then the finite difference time domain method is introduced to analyze the effects of the electromagnetic interference parameters on the security monitoring signal line. And the interference voltage of the two terminal sides on the single line is taken as evaluating indexes. Finally, the electromagnetic interference parameters are optimized by orthogonal experimental design based on the MATLAB simulation on the normal operation of equipment.

Stepwise multiple regressions application in liposome orthogonal experiments

Aim New statistical method was applied in data analysis of orthogonal experiments to optimize the preparation of liposome. Method Particle size, zeta potential, encapsulation efficiency and physical stability of liposomes were selected by orthogonal design as evaluating indicators. Through three statistical methods （direct observation, variance analysis and stepwise multiple regression）, the optimized preparing conditions were acquired and validated by experiment. Results All of the four indicators were different by these analyses. The validation experiments indicated that the optimized conditions by stepwise multiple regressions were better than that by traditional analysis. Conclusion Experiment results suggested that multiple regressions could avoid the weakness of direct observation and variance analysis, but more work should be done in preparing liposomes.

Application of orthogonal experimental design and Tikhonov regularization method for the identification of parameters in the casting solidification process

The inverse heat conduction method is one of methods to identify the casting simulation parameters. A new inverse method was presented according to the Tikhonov regularization theory. One appropriate regularized functional was established, and the functional was solved by the sensitivity coefficient and Newtonaphson iteration method. Moreover, the orthogonal experimental design was used to estimate the appropriate initial value and variation domain of each variable to decrease the number of iteration and improve the identification accuracy and efficiency. It illustrated a detailed case of AlSiTMg sand mold casting and the temperature measurement experiment was done. The physical properties of sand mold and the interracial heat transfer coefficient were identified at the meantime. The results indicated that the new regularization method was efficient in overcoming the ill-posedness of the inverse heat conduction problem and improving the stability and accuracy of the solutions.

Cavitation Optimization for a Centrifugal Pump Impeller by Using Orthogonal Design of Experiment

Cavitation is one of the most important performance of centrifugal pumps. However, the current optimization works of centrifugal pump are mostly focusing on hydraulic efficiency only, which may result in poor cavitation performance. Therefore, it is necessary to find an appropriate solution to improve cavitation performance with acceptable efficiency. In this paper, to improve the cavitation performance of a centrifugal pump with a vaned diffuser, the influence of impeller geometric parameters on the cavitation of the pump is investigated using the orthogonal design of experiment （DOE） based on computational fluid dynamics. The impeller inlet diameter D1, inlet incidence angle Aft, and blade wrap angle ~0 are selected as the main impeller geometric parameters and the orthogonal experiment of L9（3＂3） is performed. Three-dimensional steady simulations for cavitation are conducted by using constant gas mass fraction model with second-order upwind, and the predicated cavitation performance is validated by laboratory experiment. The optimization results are obtained by the range analysis method to improve cavitation performance without obvious decreasing the efficiency of the centrifugal pump. The internal flow of the pump is analyzed in order to identify the flow behavior that can affect cavitation performance. The results show that D1 has the greatest influence on the pump cavitation and the final optimized impeller provides better flow distribution at blade leading edge. The final optimized impeller accomplishes better cavitation and hydraulic performance and the NPSHR decreases by 0.63m compared with the original one. The presented work supplies a feasible route in engineering practice to optimize a centrifugal pump impeller for better cavitation performance.

Determination of Total Flavonoids in Leaves of Paliurus ramosissimus and Orthogonal Experiment Optimization Process

[Objectives] To screen the optimal extraction conditions of flavonoids from leaves of Paliurus ramosissimus( Lour.) Poir.,measure the content of flavonoids in leaves of P. ramosissimus. using the Microplate Reader,and provide experimental basis for the development of medicinal resources of P. ramosissimus. [Methods] The ultrasonic extraction method was adopted and orthogonal design was carried out to study the effects of ethanol concentration( A),ultrasonic time( B),the solid-to-liquid ratio( C) on the extraction of flavonoids from leaves of P. ramosissimus. The Microplate Reader was used to measure the content of flavonoids in leaves of P. ramosissimus. in different extraction conditions,P. ramosissimus. and the optimal extraction conditions were used to measure the content of flavonoids from leaves of P. ramosissimus.[Results]Effects of the ultrasonic extraction method on the extraction rate of flavonoids from leaves of P. ramosissimus: extraction times >ethanol concentration > Ultrasound time > solid-liquid ratio. The screened optimal extraction process was: ethanol concentration of 65%,the solid-to-liquid ratio of 1∶ 25,ultrasonic time of 2 h and extraction times Under this condition,the extraction rate of total flavonoids in leaves of P. ramosissimus. was 2. 56%. [Conclusions] This method is simple and feasibility,reliable,and suitable for rapid measurement with large samples.

Treatment performance of integrated biological aerated filter by orthogonal experiments

Biological aerated filters have many advantages such as small volume and high treatment efficiency. This research focused on sewage treatment performance of integrated biological aerated filter (IBAF) under different conditions such as aeration, hydraulic retention time and the height of fillers layer, to identify the turn of marked affecting factor of removal performance through orthogonal experiments, optimize the function parameter of IBAF, reveal the regularity of sewage treatment of IBAF under different conditions, and adopt suitable measures to guarantee excess water quality of IBAF.

Characterization of the adsorption behavior of aqueous cadmium on nanozero-valent iron based on orthogonal experiment and surface complexation modeling

Polyvinylpyrrolidone K-30(PVP) was introduced into the preparation of nanozero-valent iron(n ZVI) and the traditional liquid-phase reduction was improved. The introduction of PVP simplified the traditional method.The n ZVI prepared with this new approach showed excellent surface characters and high performance on the removal of cadmium. TEM results showed that the aggregates of n ZVI can reach to several micrometers in length but less than 100 nm in diameter. The iron particles that were enclosed by a layer of oxide film that is less than10 nm, demonstrated that the n ZVI possesses a core–shell structure. BET results indicate that the specific surface area of the n ZVI was 20.3159 m^2g^(-1). A three factor and three level orthogonal experiment was employed to find out the dominant factor that affects the removal rate of cadmium by n ZVI. Based on the range values, the prominence order of each factor was: initial p H of the solution N initial concentration of cadmium N dosage of n ZVI, the range was 96.453, 3.294 and 1.747, respectively. A simulation was performed under the same condition and a same conclusion was derived, this consistence confirmed the validity of the conclusion that p H is the most significant factor that affects the adsorption efficiency.

CVD Method for Carbon Nanotubes Preparation Based on Orthogonal Experiment Using C_3H_6

Carbon nanotubes (CNTs) have potential applications in many fields, chemical vapor deposition (CVD) is an effective method for CNTs preparation. By CVD, the catalytic pyrolysis temperature, pyrolysis time and the size of the raw gas flow have a great influence on yield rate of CNTs and their form. In this paper, the orthogonal experiment analysis method is used for studying the influence factors of yield rate of CNTs. Research results show that, in the suitable temperature range of preparing CNTs, there is relatively more CNTs with excellent morphology, otherwise, if the temperature is too low, the growth of CNTs will not be sufficient; if the temperature is too high, then CNTs will be generated with excessive defects; with longer growth time of suitable pyrolysis of CNTs, higher yield of CNTs will be obtained; CNTs morphology with reaction time is not proportional; too low or too high raw gas flow rate is not conducive to the growth of CNTs. We have found the optimum conditions for the CNTs preparation: pyrolysis temperature 68 degrees C, pyrolysis time 35 min, propylene flow rate of 180 mL/min. The results have a reference value for the preparation of CNTS and their composites.

Orthogonal design of experiment and analysis of abrasive water jet cutting on carbon fiber reinforced composites

The carbon fiber reinforced composite is a new type of composite material with an excellent property in strength and elastic modulus,and has found extensive applications in aerospace,energy,automotive industry and so on.However,this composite has a strict requirement on processing techniques,for example,brittle damage or delamination often exists in conventional processing techniques.Abrasive water jet machining technology is a new type of green machining technique with distinct advantages such as high-energy and thermal distortion free.The use of abrasive water jet technique to process carbon fiber composite materials has become a popular trend since it can significantly improve the processing accuracy and surface quality of carbon fiber composite materials.However,there are too many parameters that affect the quality of an abrasive water jet machining.At present,few studies are carried out on the parameter optimization of such a machining process,which leads to the unstable quality of surface processing.In this paper,orthogonal design of experiment and regression analysis were employed to establish the empirical model between cutting surface roughness and machining process parameters.Then a verified model was used to optimize the machining process parameters for abrasive water jet cutting carbon fiber reinforced composites.

Orthogonal Experiments for Controlling the Formation of DBPs During Preozonation of Bromide-Containing Raw Water

Orthogonal method was adopted to optimize the preozonation process and to minimize the bromate formation. Factors such as contact time, pH and ammonia concentration were investigated by orthogonal experiments to understand the interaction of various operation conditions on the formation of bromate and other disinfection byproducts(DBPs). Results showed that pH had the most significant influence on the minimization of bromate formation. The factors influencing the formation of bromate were in order of pH > contact time > ammonia concentration. For the formation of trihalomethanes(THMs) and haloacetic acids(HAAs), however, contact time significantly influenced their formation potential. In the practical preozonation process of waterworks, it is appropriate to set preozonation contact time to be 20 min. In order to minimize the formation of bromate, pH value of the raw water should be adjusted to 6. 0, and a certain concentration of ammonia could be added into the water to strengthen the minimization effect when the concentration of bromide in the raw water is higher than that in the experimental water.

Application of Orthogonal Experiment in EDM Using the Suspended Powder Fluid

To solve the problems of EDM when using the ordinary fluid and mold manufacturing,this paper provides the orthogonal experiment in the suspended powder fluid,which can optimize the main process parameters.And it also achieves the technology of EDM in the suspended powder fluid primarily.

Parameters optimization for direct contact membrane distillation based on orthogonal experiment

Parameter optimization integrating operation parameters and structure parameters for the purpose of high permeate flux,high productivity and low exergy consumption of direct contact membrane distillation (DCMD) process was conducted based on Taguchi experimental design. L16(45) orthogonal experiments were carried out with feed inlet temperature,permeate stream inlet temperature,flow rate,module packing density and length-diameter ratio as optimization parameters and with permeate flux,water productivity per unit volume of module and water production per unit exergy loss separately as optimization objectives. By using range analysis method,the dominance degree of the various influencing factors for the three objectives was analyzed and the optimum condition was obtained for the three objectives separately. Furthermore,the multi-objectives optimization was performed based on a weight grade method. The combined optimum conditions are feed inlet temperature 75℃,packing density 30% ,length-diameter ratio 10,permeate stream inlet temperature 30 ℃ and flow rate 25 L/h,which is in order of their dominance degree,and the validity of the optimization scheme was confirmed.

Optimization of in vitro Regeneration System of Benihoppe Strawberry (Fragaria × ananassa Duch.) with Orthogonal Experiment Design

[Objective] This study aimed to optimize the in vitro regeneration system of Benihoppe strawberry. [Method] Based on orthogonal experiment, the effects of different medium types, plant growth regulator types and concentrations on the regeneration of adventitious shoots of Benihoppe strawberry leaves were in- vestigated. [Result] IBA is an important factor affecting the multiplication of adventitious shoots of Benihoppe strawberry leaves; the optimal induction medium is MS ＋ 2.0 mg/L TDZ ＋ 0.2 mg/L IBA, with an induction rate of 90.00% ; the optimal differentiation medium is MS ＋ 2.0 mg/L 6-BA ＋ 0.2 mg/L IBA, with a differentiation rate of 8.1% ; the optimal multiplication medium is MS ＋ 1.0 mg/L 6-BA ＋ 0.2 mg/L IBA, with an average multiplication rate of each adventi- tious shoot of 7.67 ; the optimal subculture medium is MS ＋ 0.5 mg/L 6-BA ＋ 0. 1 mg/L 2, 4-D, with an average seeding height in each treatment of 5.98 cm; the optimal rooting medium is 1/2MS ＋ O. 5 mg/L 6-BA ＋ 0. 1 mg/L 2, 4-D, with an average number of roots in each treatment of 4.5. [ Conclusion] This stud- y laid the foundation for further investigating the genetic transformation of strawberry and improving the quality of strawberry at the genetic level.

Optimization of Ultrasonic Extraction Process of Total Flavonoids from Mulberry Leaves by Orthogonal Experiment

In this study, by using mulberry leaves as raw materials, ultrasonic extraction process of total flavonoids from mulberry leaves was optimized by orthogonal experiment. Results showed that the maximum yield of total flavonoids （6.1% ） was obtained from mulberry leaves with addition of 45 times the volume of water by ultrasonic extraction at 55 ℃ for three times, 55 min each. According to the verification test, the optimized technical process was reasonable and feasible with high stability.

Optimization of Conditions for Extracting Luteolin from Ternate Grape Fern Herb by an Orthogonal Experiment

[Objectives] This study was conducted to optimize the extraction process of luteolin, a natural product of Ternate Grape Fern Herb, so as to provide a theoretical research basis for the chemical composition, pharmacological research and preparation development of Ternate Grape Fern Herb. [Methods] The effects of four factors including ultrasonic extraction time, liquid-to-material ratio, ultrasonic extraction temperature and ethanol concentration on extraction yield of luteolin from Ternate Grape Fern Herb were investigated by the ultrasonic-assisted extraction technology, through a single-factor experiment and an orthogonal experiment based on the single-factor experiment, and the experimental data was subjected to variance analysis and SSR analysis of the significance of differences between groups by SPSS20.0 software to select the optimal extraction process conditions. [Results] The optimal extraction process conditions were as follows: ultrasonic extraction time 25 min, liquid-to-material ratio 25∶1 ml/g, ethanol volume fraction 60%, ultrasonic extraction temperature 85 ℃. [Conclusions] The results were verified, and it was determined that the ultrasonic-assisted extraction process established in this study is reasonable and reliable, and can be used for the extraction of luteolin.

Simulation analysis of hot dip galvanizing process parameters based on orthogonal experimental design

An iron and steel company＇ s hot galvanizing technology was chosen as the object. An orthogonal experimental scheme with 5 factors of mixed level was designed, according to the various factors affecting the distribution of slag. For each scheme, the amount of slag and slag height in different orthogonal schemes by simulation were obtained with FLUENT software. Then, range and variance analyses were selected to compare the trend of slag height in the different process parameters of the hot dip galvanizing process. Finally, the optimal combination of the process parameters was obtained.