Exploring the effect of cooling rate on non-isothermal crystallization of copolymer polypropylene by fast scanning calorimetry

Polypropylene is commonly used as a binder for ceramic injection molding,and rapid cooling is often encountered during processing.However,the crystallization behavior of polypropylene shows a strong dependence on cooling rate due to its semi-crystalline characteristics.Therefore,the influence of cooling rate on the quality of final product cannot be ignored.In this study,the fast differential scanning calorimetry(FSC)test was performed to study the influence of cooling rate on the non-isothermal crystallization behavior and non-isothermal crystallization kinetics of a copolymer polypropylene(PP BC03B).The results show that the crystallization temperatures and crystallinity decrease as the cooling rate increases.In addition,two exothermic peaks occur when cooling rate ranges from 30 to 300 K·s^(-1),indicating the formation of another crystal phase.Avrami,Ozawa and Mo equations were used to explore the non-isothermal crystallization kinetics,and it can be concluded that the Mo method is suitable for this study.

Efficient and selective removal of Pb(Ⅱ) from landfill leachate using L-serine-modified polyethylene/polypropylene nonwoven fabric synthesized via radiation grafting technique

In this study,to efficiently remove Pb(Ⅱ) from aqueous environments,a novel L-serine-modified polyethylene/polypropylene nonwoven fabric sorbent(NWF-serine)was fabricated through the radiation grafting of glycidyl methacrylate and subsequent L-serine modification.The effect of the absorbed dose was investigated in the range of 5–50 kGy.NWF-serine was characterized by Fourier transform infrared spectroscopy,thermogravimetric analysis,and scanning electron microscopy.Batch adsorption tests were conducted to investigate the influences of pH,adsorption time,temperature,initial concentration,and sorbent dosage on the Pb(Ⅱ) adsorption performance of NWF-serine.The results indicated that Pb(Ⅱ) adsorption onto NWF-serine was an endothermic process,following the pseudo-second-order kinetic model and Langmuir isotherm model.The saturated adsorption capacity was 198.1 mg/g.NWF-serine exhibited Pb(Ⅱ) removal rates of 99.8% for aqueous solutions with initial concentrations of 100 mg/L and 82.1% for landfill leachate containing competitive metal ions such as Cd,Cu,Ni,Mn,and Zn.Furthermore,NWF-serine maintained 86% of its Pb(Ⅱ) uptake after five use cycles.The coordination of the carboxyl and amino groups with Pb(Ⅱ) was confirmed using X-ray photoelectron spectroscopy and extended X-ray absorption fine structure analysis.

Characterization and Modeling of Mechanical Properties of Additively Manufactured Coconut Fiber-Reinforced Polypropylene Composites

In the face of the increased global campaign to minimize the emission of greenhouse gases and the need for sustainability in manufacturing, there is a great deal of research focusing on environmentally benign and renewable materials as a substitute for synthetic and petroleum-based products. Natural fiber-reinforced polymeric composites have recently been proposed as a viable alternative to synthetic materials. The current work investigates the suitability of coconut fiber-reinforced polypropylene as a structural material. The coconut fiber-reinforced polypropylene composites were developed. Samples of coconut fiber/polypropylene (PP) composites were prepared using Fused Filament Fabrication (FFF). Tests were then conducted on the mechanical properties of the composites for different proportions of coconut fibers. The results obtained indicate that the composites loaded with 2 wt% exhibited the highest tensile and flexural strength, while the ones loaded with 3 wt% had the highest compression strength. The ultimate tensile and flexural strength at 2 wt% were determined to be 34.13 MPa and 70.47 MPa respectively. The compression strength at 3 wt% was found to be 37.88 MPa. Compared to pure polypropylene, the addition of coconut fibers increased the tensile, flexural, and compression strength of the composite. In the study, an artificial neural network model was proposed to predict the mechanical properties of polymeric composites based on the proportion of fibers. The model was found to predict data with high accuracy.

Influence ofβ-nucleating Compound Agents on the Mechanical Properties and Crystallization Behavior of Polypropylene Random Copolymer

A novel polypropylene random(PPR)composite materials with optimized properties was developed by addingβ-nucleating compound agents(rare earth complex WBG-2 and aryl amide derivative TMB-5)and ternary compound modifier(TPE/WBG-2/CaCO_(3)).The effects of differentβ-nucleating agents and ternary compound modifier on the mechanical properties and crystallization behavior of PPR were analyzed.The results show that,compared with pure PPR materials,both WBG-2 and TMB-5 could significantly improve the impact strength of PPR.The crystallization temperature of PPR increased with the addition ofβ-nucleating agent.The modified PPR prepared with ternary compound modifier showed the most excellent comprehensive properties.

Rotator cuff repair with an interposition polypropylene mesh:A biomechanical ovine study

BACKGROUND Chronic large to massive rotator cuff tears are difficult to treat and re-tears are common even after surgical repair.We propose using a synthetic polypropylene mesh to increase the tensile strength of rotator cuff repairs.We hypothesize that using a polypropylene mesh to bridge the repair of large rotator cuff tears will increase the ultimate failure load of the repair.AIM To investigate the mechanical properties of rotator cuff tears repaired with a polypropylene interposition graft in an ovine ex-vivo model.METHODS A 20 mm length of infraspinatus tendon was resected from fifteen fresh sheep shoulders to simulate a large tear.We used a polypropylene mesh as an interposition graft between the ends of the tendon for repair.In seven specimens,the mesh was secured to remnant tendon by continuous stitching while mattress stitches were used for eight specimens.Five specimens with an intact tendon were tested.The specimens underwent cyclic loading to determine the ultimate failure load and gap formation.RESULTS The mean gap formation after 3000 cycles was 1.67 mm in the continuous group,and 4.16 mm in the mattress group(P=0.001).The mean ultimate failure load was significantly higher at 549.2 N in the continuous group,426.4 N in the mattress group and 370 N in the intact group(P=0.003).CONCLUSION The use of a polypropylene mesh is biomechanically suitable as an interposition graft for large irreparable rotator cuff tears.

The effect of pulse voltage rise rate on the polypropylene surface hydrophilic modification by ns pulsed nitrogen DBD

The nanosecond(ns) pulsed nitrogen dielectric barrier discharge(DBD) is employed to enhance the hydrophilicity of polypropylene(PP) surface and improve its application effect.The discharge characteristics of the ns pulsed nitrogen DBD with different pulse rise times(from 50to 500 ns) are investigated by electrical and optical diagnostic methods and the discharge uniformity is quantitatively analyzed by image processing method.To characterize the surface hydrophilicity,the water contact angle(WCA) is measured,and the physical morphology and chemical composition of PP before and after modification are analyzed to explore the effect of plasma on PP surface.It is found that with increasing pulse rise time from 50 to 500 ns,DBD uniformity becomes worse,energy efficiency decreases from 20% to 10.8%,and electron density decrease from 6.6 × 10^(11)to 5.5 × 10^(11)cm^(-3).The tendency of electron temperature is characterized with the intensity ratio of N_(2)/N_(2)^(+)emission spectrum,which decreases from 17.4 to15.9 indicating the decreasing of T_(e) with increasing pulse rise time from 50 to 500 ns.The PP surface treated with 50 ns pulse rise time DBD has a lower WCA(~47°),while the WCA of PP treated with 100 to 500 ns pulse rise time DBD expands gradually(~50°–57°).According to the study of the fixed-point WCA values,the DBD-treated PP surface has superior uniformity under50 ns pulse rise time(3° variation) than under 300 ns pulse rise time(8° variation).After DBD treatment,the increased surface roughness from 2.0 to 9.8 nm and hydrophilic oxygencontaining groups on the surface,i.e.hydroxyl(-OH) and carbonyl(C=O) have played the significant role to improve the sample’s surface hydrophilicity.The short pulse voltage rise time enhances the reduced electric field strength(E/n) in the discharge space and improves the discharge uniformity,which makes relatively sufficient physical and chemical reactions have taken place on the PP surface,resulting in better treatment uniformity.

Effect of Synthetic Conditions and Thickener Formulation on the Rheological and Tribological Properties of Polypropylene Grease

Polypropylene(PP)grease holds great potential for special industrial applications.In this study,synthetic conditions,thickener content,and the ratio of two different molecular weight PPs were investigated systematically using a rheometer,scanning electron microscope,X-ray diffraction,Fourier transform infrared spectrometer,oscillating tribometer,and 3D surface profiler measurements.The results showed that suitable synthetic conditions are two quenching cycles,and the synthetic temperature and time is 240℃for 12 h.The rheological analysis showed that thickener content and different proportions of the two PP molecular weights have a significant influence on the rheological properties of PP grease.High molecular weight PP(H-PP)has a stronger thickening ability than low molecular weight PP(L-PP).The higher the amount of H-PP in the fixed thickener content or the higher the thickener content with a specific proportion,the higher the viscoelasticity of PP grease.The tribological performance is related to the rheological properties.The proportion of two different molecular weight PPs in the thickener content should be appropriate;excessive H-PP content leads to lubrication failure.

Effect of Polypropylene Fiber on the Unconfined Compressive Strength of Loess with Different Water Content

Fiber-reinforced soils have been of great interest to experimenters for building foundations’strength performance,time,and economy.This paper investigates the effects of water content and polypropylene fiber dosage and length on loess’s unconfined compressive strength(UCS)according to the central composite response surface design test procedure.The water content is 11%–25%,the mass ratio of fiber to soil is 0.1%–0.9%,and the fiber length ranges from 6–18 mm.The response surface method(RSM)developed full quadratic models of different variables with response values.After analysis of variance(ANOVA),the mathematical model developed in this study was statistically significant(p≤0.05)and applicable to the optimization process.The optimization results showed that the optimal water content values,fiber amount,and fiber length were 16.41%,0.579%,and 14.90 mm,respectively.The unconfined compressive strength of the optimized specimens was increased by 288.017 kPa.The research results can reference the design and construction of fiber-reinforced soil in practical projects such as road base engineering and foundation engineering.

A Circular Economy Use of Post-Consumer Polypropylene Packaging for Low Thermal Conductive and Fire-Retardant Building Material Applications

Wastes from polypropylene(PP)packages are accumulating every year because it is one of the most widely consumed and short lifecycle products.This paper aims to develop low thermal conductive and fire-retardant materials from post-consumer PP(pPP)packages.Ammonium polyphosphate(APP)and hollow glass microsphere(HGM)were further added to improve the fire retardancy and thermal conductivity of pPP.The influence of APP and HGM on the mechanical and thermal properties,fire retardancy and thermal conductivity of pPP were investigated and compared with that of virgin PP(vPP).HGM was constantly added at 5 wt%while the content of APP was varied from 5 to 20 wt%.Experimental results showed that the tensile and flexural strengths were reduced with increasing APP concentrations.A morphological study confirmed the poor interfacial adhesion and debonding of each component during the applied load.Formulations containing APP less than 10 wt%did not show a satisfying fire retardancy rating due to the long self-extinguishing time.Further flame dipping and cotton ignition were observed for these formulations.With 15 and 20 wt%APP,the fire rating was significantly improved from no rating to V-0.The conductive heat transfer coefficient(k)was reduced by the presence of HGM.Based on these results,the formulation with 15 and 20 wt%could be used as a low k,fire-retardant building material.

Experimental study on mechanical and frost heave behaviors of silty clay improved by polyvinyl alcohol and polypropylene fiber

Silty clay is widely used as subgrade filler in cold regions,which suffer from frost heave in winter and mud pumping in spring.In this study,polyvinyl alcohol(PVA)and polypropylene(PP)fiber were used to improve the mechanical and frost heave behavior of silty clay in cold regions,and the direct shear test and one-dimensional frost heave test were employed in studying improvement effects.Moreover,improvement mechanisms of PVA and PP fiber were analyzed based on test results.The main findings are as follows.(1)Both PP and PVA can heighten the strength of silty clay and suppress frost heave,but the PVA solution has a more decisive influence on improving mechanical properties than PP fiber.(2)The improvement mechanism of the PVA solution is cementing.The improvement effect of 2%PVA solution is the best,which can increase the shear strength by approximately 40%–60%at different stress levels and decrease the frost heave ratio from 0.89%to 0.16%at optimal water content.(3)For 2%PVA improved samples,0.25%PP fiber can further increase soil cohesion by approximately 20–30 kPa at different stress levels and further decrease the frost heave ratio from 0.16%to 0.07%at optimal water content.The improvement effect is neglectable when the PP fiber content exceeds 0.25%.Overall,2%PVA with 0.25%PP fiber is the optimum combination to improve silty clay in cold regions.

Matrix-Material Fabrication Technique and Thermogravimetric Analysis of Banana Fiber Reinforced Polypropylene Composites

From the environmental consideration,it would be very interesting to use natural fibers such as banana,jute or coir as reinforcement materials instead of artificial fibers or any kind of synthetic materials.Natural fibers have many advantages over synthetic ones.Polypropylene banana fiber composites(PPBC)are prepared using untreated and alkali-treated banana fibers at 10-25%by weight of the fiber loading.The thermal properties of polypropylene natural fiber composites are very important for technological uses.Thermogravimetric measurements show that the incorporation of banana fiber into PP enhances the thermal stability of composites containing treated fibers,in comparison with untreated fibers.A composite of biodegradable polypropylene(PP)reinforced with short banana natural fibers was prepared by melt blending followed by a hot press molding system.The thermal properties of matrix materials were studied using thermogravimetric analyzers TGA units.It is observed that the introduction of short banana fibers slightly improved the thermo oxidative stability of PP-banana composites.Physical and chemical changes occurred through dehydration,phase transition,molecular orientation,crystallinity disruption,oxidation and decomposition,and incorporation of several functional groups.Systematic investigations of the thermal behavior of polymers in gas,vacuum or inert atmosphere give the knowledge of how change takes place in polymers.To understand such changes thermogravimetric analysis(TGA)and thermal analysis(TG)were performed.It is observed reinforcement of short banana fiber leads to little improvement in the thermooxidative stability of PPBC.Due to the enhancement of thermo-mechanical properties,such composites may be used as building materials namely roof materials,selling materials and many other engineering applications.

医用丝线和Polypropylene缝线用于皮肤除皱的对比研究

目的:研究临床常用外科缝线医用丝线和在国外用于皮肤提升除皱术中的常用Polypropylene缝线对皮肤胶原蛋白的影响。方法:将21只造模成功的衰老家兔随机分为三组,即Polypropylene缝线(P)组、医用丝线(S)组和空白对照组。在缝线植入术后第3、7、15、30、45、60及90天切取P组和S组手术标记区及对照组取样区皮肤,做羟脯氨酸(HYP)的含量测定。结果:P组、S组和对照组在不同时间点测得的HYP含量差异有统计学意义(P<0.05)。测定时点与手术分组存在交互作用(P<0.05)。HYP含量为P组>S组>对照组。结论:Polypropylene缝线比医用丝线能更为有效的改善皮肤弹性和皱纹。

Preliminary study of viscoelastic properties of MAPP-modified wood flour/polypropylene composites

Viscoelastic properties of maleated polypropylene （MAPP）-modified wood flour/polypropylene composites （WPC） were investigated by both a compression stress relaxation method and dynamic mechanical analyses （DMA）. Three wood to polymer ratios （40：60, 60：40, and 80：20） and five MAPP loading levels （0, 1, 2, 4 and 8%） were used to study their effects on the viscoelastic prop- erties of MAPP-WPC. The results show that： 1） higher wood to polymer ratio corresponds to higher stress relaxation levels for unmodified WPC. The modification with MAPP has an obvious effect on the stress relaxation of MAPP-WPC at higher wood to polymer ratios （60：40 and 80：20）, but almost no effect at the 40：60 wood to polymer ratio. The optimal MAPP loading level for the wood to polymer ratio of 60：40 appears at 1%; 2） the storage modulus reaches its maximum at a MAPP loading level of 1% for wood to polymer ratios of 40：60 and 60：40, while for the 80：20 wood to polymer ratio, a higher storage modulus is observed at higher MAPP loading levels, which is quite consistent with the stress relaxation results. The results suggested that a suitable loading level of MAPP has a positive effect on the viscoelastic properties of WPC at higher wood to polymer ratios. Excessive MAPP loading would have resulted in adverse effects.

医用丝线和Polypropylene缝线对植入部位皮肤衰老因子影响的实验研究

目的通过衰老动物模型研究临床常用外科缝线医用丝线和皮肤提升除皱术中的常用聚丙烯缝线(Polypropylene缝线)对皮肤抗衰老指标的影响,探讨手术缝线对皮肤除皱的机制。方法将21只造模成功的衰老家兔随机分为三组,并于缝线植入术后第3,7,15,30,45,60,90天切取手术标记区及对照组取样区皮肤,测定皮肤组织中超氧化物歧化酶(SOD)的活性及过氧化氢(H2O2)的含量。结果缝线植入组和对照组在不同时间点测得的SOD及H2O2含量差异有统计学意义(P<0.05)。测定时点与手术分组存在交互作用(P<0.05)。结论植入缝线可以起到一定的抗衰老作用,Polypropylene缝线比医用丝线能更为有效地改善皮肤弹性和皱纹。

Catalytic performances of kaoline and silica alumina in the thermal degradation of polypropylene

Polypropylene was cracked thermally and catalytically in the presence of kaoline and silica alumina in a semi batch reactor in the temperature range 400℃～550℃ in order to obtain suitable liquid fuels.The dependencies between process temperatures,types of catalyst,feed compositions and product yields of the obtained fuel fractions were found.It was observed that up to 450℃ thermal cracking temperature,the major product of pyrolysis was liquid oil and the major product at other higher temperatures(475℃～550℃) are viscous liquid or wax and the highest yield of pyrolysis product is 82.85% by weight at 500℃.Use of kaoline and silica alumina decreased the reaction time and increased the yield of liquid fraction.Again the major pyrolysis product in catalytic pyrolysis at all temperatures was low viscous liquid oil.Silica alumina was found better as compared to kaoline in liquid yield and in reducing the reaction temperature.The maximum oil yield using silica alumina and kaoline catalyst are 91% and 89.5% respectively.On the basis of the obtained results hypothetical continuous process of waste polypropylene plastics processing for engine fuel production can be presented.

Synthesis and Application of Novel Triazine-Based Charring-Foaming Agents in Intumescent Flame Retardant Polypropylene

Three novel triazine-based charring-foaming agents (M2-CFA,M4-CFA,and M6-CFA) were synthesized successfully with only water as the solvent and were characterized by FT-IR and thermal gravimetric analysis (TGA).These three charring-foaming agents and the byproduct 944-by were employed to study the effectiveness of the novel intumescent flame retardant dopant on the fire retardancy of polypropylene (PP) investigated through UL-94 and limiting oxygen index (LOI) tests.TGA results showed that the M4-CFA presented good char formation ability (char residue: 26.8% at 700 ℃).It was found that the sample with a 2/1 mass ratio of APP to M4-CFA exhibited the best flame retardancy among all the PP composites: 35.5% LOI and a V-0 rating of UL-94.Additionally,the microstructure and morphology of char residues were further studied by XRD,Raman spectroscopy and SEM.

Reinforcing effects of modified Kevlar~ fiber on the mechanical properties of wood-flour/polypropylene composites

Kevlar fiber （KF） is a synthesized product with strong mechanical properties. We used KF as a reinforcement to improve the mechanical properties of wood-flour/polypropylene （WF/PP） composites. KF was pretreated with NaOH to improve its compatibility with the thermoplastic matrix. Maleated polypropylene （MAPP） was used as a coupling agent to improve the interfacial adhesion between KF, WF, and PP. Incorporation of KF improved the mechanical properties of WF/PP composites. Treatment of KF with NaOH resulted in further improvement in mechanical strength. Addition of 3% MAPP and 2% hydrolyzed KF （HKF） led to an increment of 93.8% in unnotched impact strength, 17.7% in notched impact strength, 86.8% in flexure strength, 50.8% in flexure modulus, and 94.1% in tensile strength compared to traditional WF/PP composites. Scanning electron microscopy of the cryo-fractured section of WF/PP showed that the HKF surface was rougher than the virgin KF, and the KF was randomly distributed in the composites, which might cause a mechanical interlocking between KF and polypropylene molecules in the composites.

DYNAMIC RHEOLOGICAL BEHAVIOR OF POLYPROPYLENE FILLED WITH ULTRA-FINE POWDERED RUBBER PARTICLES

Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.

DISPERSION AND TENSILE BEHAVIOR OF POLYPROPYLENE/MONTMORILLONITE NANOCOMPOSITES PRODUCED VIA MELT INTERCALATION

Most of the articles on polymer nanocomposites focus on the importance of chemistry used to modify the surface of the clay, usually montmorillonite (MMT), and characterization of the nano-scale structure obtained. The role and importance of processing were also discussed recently. However, few papers concerning the correlation between morphology of MMT and mechanical properties were published. In order to understand. the tensile behavior of PP/Montmorillonite (MMT) nanocomposites better, and to further improve the reinforcement efficiency, we first prepared the PP nanocomposites via direct melt intercalation using conventional twin-screw extrusion. The dispersion and tensile property of the composites were then investigated by SEM, XRD, TEM and a video-controlled tensile set-up. The macroscopic and microscopic dispersion of MMT in PP matrix was verified by XRD and TEM, combined with SEM. The tensile properties were obtained by video-controlled tensile set-up, which gives true stress-strain curve. It was found that a partly intercalated and partly exfoliated structure (also called incomplete exfoliation) existed in the system. Though the tensile strength of PP nanocomposites is not much improved in engineering stress-strain curves, more than 20% increase of true stress was found in a true stress-strain experiment at high true strain, which indicates that only oriented silicate layers can have a big effect on tensile properties: Not only orientation of silicate platelets but also the degree of exfoliation is a key factor to determine the reinforcement efficiency. The reinforcement efficiency of MMT has been discussed based on the 'continuum' Halpin-Tsai equations. A good agreement was found between experimental data and theoretical prediction by changing N value (number of platelets per stack) which corresponding to different state of the dispersion of MMT in PP matrix.

Polypropylene crisper and 1-MCP delay the softening,lignification and transcription levels of related enzyme genes of golden needle mushrooms(Flammulina velutipes)

The fresh postharvest golden needle mushroom(Flammulina velutipes) sporocarp has a high moisture content and crisp texture, but it still has high physiological activity and respiration, leading to senescence and quality deterioration.Treatments with 1-methylcyclopropene(1-MCP) and polypropylene(PP) crispers were used to study the changes of lignification and softening of F. velutipes during storage. The main findings were as follows: the crisper packaging could effectively prolong the storage time of F. velutipes;either the 1-MCP treatment, crisper packaging or the combination of the two treatments could significantly inhibit the accumulation of lignin and the decreases in the contents of cellulose and pectin, and had certain inhibitory effects on the activities of enzymes involved in lignification and softening including phenylalanine ammonia-lyase(PAL), cinnamyl alcohol dehydrogenase(CAD), cellulase(Cx), pectin methylesterase(PME) and polygalacturonase(PG). Among them, the inhibitory effect of the crisper packaging was higher than the 1-MCP treatment, while the combination of the two treatments was the best. The results of transmission electron microscopy(TEM) and scanning electron microscopy(SEM) showed that the crisper packaging in combination with the 1-MCP treatment could effectively maintain the integrity and stability of the F. velutipes cellular structure and inhibit the emergence of plasmolysis to prevent cell membrane rupture. The transcription levels showed that the crisper packaging and the combination of the 1-MCP treatment and crisper packing could effectively affect the expression of genes for enzymes related to lignification and softening of F. velutipes. In conclusion, 1-MCP and PP crispers could delay the lignification and softening of F. velutipes during storage.