A significant portion of the national water supply can be attributed to de facto or unplanned potable reuse, though the extent of its contribution is difficult to estimate. Fortunately, the contribution of Water Resou...A significant portion of the national water supply can be attributed to de facto or unplanned potable reuse, though the extent of its contribution is difficult to estimate. Fortunately, the contribution of Water Resource Recovery Facility (WRRF) effluent to waters that supply drinking water treatment plants has been documented by some communities. In the United States (US), among the top 25 most impacted drinking water treatment plants by upstream WRRF, 16% of the influent flow to the drinking water treatment plant under average streamflow and up to 100% under low-flow conditions is WRRF effluent. Currently, the full extent of de facto reuse in the US may be much higher because of population growth. The scenario is no different for Beaufort-Jasper Water and Sewer Authority (BJWSA) in South Carolina, US, with contributions to the Savannah River originating from numerous WRRF and other upstream dischargers. South Carolina coastal utilities such as BJSWA are considering direct and indirect potable reuse options, driven by disposal limitations and challenges. Currently, South Carolina does not have a framework, guidelines, or regulations for reuse, but discussions have started among the regulated community. In addition to understanding the extent of de facto reuse, the state will need to develop standards and best practices to enable future adoption of planned potable reuse solutions to water resources challenges. Such guidance should address human health risk management and technical considerations regarding treatment in addition to other factors, including source control, storage, fail-safe operation, monitoring, non-cost factors, and public acceptance. This study conducted a mapping assessment specific to BJWSA, sampled at four locations on Savannah River, and observed that de facto reuse is approximately 4.6% to 5.9% during low-flow months and is within the range generally observed nationwide. When coupled with evidence that planned potable reuse can improve human health and environmental risks, this practice is a meaningful option in the water supply portfolio for many utilities.展开更多
Laser powder bed fusion(L-PBF) has attracted significant attention in both the industry and academic fields since its inception, providing unprecedented advantages to fabricate complex-shaped metallic components. The ...Laser powder bed fusion(L-PBF) has attracted significant attention in both the industry and academic fields since its inception, providing unprecedented advantages to fabricate complex-shaped metallic components. The printing quality and performance of L-PBF alloys are infuenced by numerous variables consisting of feedstock powders, manufacturing process,and post-treatment. As the starting materials, metallic powders play a critical role in infuencing the fabrication cost, printing consistency, and properties. Given their deterministic roles, the present review aims to retrospect the recent progress on metallic powders for L-PBF including characterization, preparation, and reuse. The powder characterization mainly serves for printing consistency while powder preparation and reuse are introduced to reduce the fabrication costs.Various powder characterization and preparation methods are presented in the beginning by analyzing the measurement principles, advantages, and limitations. Subsequently, the effect of powder reuse on the powder characteristics and mechanical performance of L-PBF parts is analyzed, focusing on steels, nickel-based superalloys, titanium and titanium alloys, and aluminum alloys. The evolution trends of powders and L-PBF parts vary depending on specific alloy systems, which makes the proposal of a unified reuse protocol infeasible. Finally,perspectives are presented to cater to the increased applications of L-PBF technologies for future investigations. The present state-of-the-art work can pave the way for the broad industrial applications of L-PBF by enhancing printing consistency and reducing the total costs from the perspective of powders.展开更多
分析目前高中英语阅读教学存在功利化、模式僵化、碎片化、浅层化、资源利用不充分等典型问题。针对这些问题,构建REUSE模式,即Reviewing(复习)—Exploring(探索)—Unlocking(揭秘)—Sharing(分享)—Evaluating(评价)。以人教版高中《...分析目前高中英语阅读教学存在功利化、模式僵化、碎片化、浅层化、资源利用不充分等典型问题。针对这些问题,构建REUSE模式,即Reviewing(复习)—Exploring(探索)—Unlocking(揭秘)—Sharing(分享)—Evaluating(评价)。以人教版高中《英语》必修3 Unit 3 The million pound bank note为例,探究在高中英语阅读教学中运用REUSE模式的教学流程及应用注意事项。展开更多
A water quality model for water reuse was made by mathematics induction. The relationship among the reuse rate of treated wastewater(R), pollutant concentration of reused water( Cs ), pollutant concentration of in...A water quality model for water reuse was made by mathematics induction. The relationship among the reuse rate of treated wastewater(R), pollutant concentration of reused water( Cs ), pollutant concentration of influent( C0), removal efficiency of pollutant in wastewater( E), and the standard of reuse water were discussed in this study. According to the experiment result of a toilet wastewater treatment and reuse with membrane bioreactors, R would be set at less than 40%, on which all the concerned parameters could meet with the reuse water standards. To raise R of reuse water in the toilet, an important way was to improve color removal of the wastewater.展开更多
The increasing complexity and size of configuration knowledge bases requres the provisionof advanced methods supporting the development of the actual configuration process and design reuse.A new framework to find a fe...The increasing complexity and size of configuration knowledge bases requres the provisionof advanced methods supporting the development of the actual configuration process and design reuse.A new framework to find a feasible and practical product configuration method is presented in masscustomization. The basic idea of the appoach is to integrate case-based reasoning (CBR) with a con-straint satisfaction problem(CSP). The similarity measure between a crisp and range is also given,which is common in case retrieves. Based on the configuration model, a product platform and customerneeds, case adaptation is carried out with the repair-based algorithm. Lastly, the methodology in theelevator configuration design domain is tested.展开更多
The mountainous abandoned mine land is often distributed in the fomi of fragmented patches. Therefore, it can greatly promote the reuse value of abandoned mine land and relieve the pressure of land demand to realize t...The mountainous abandoned mine land is often distributed in the fomi of fragmented patches. Therefore, it can greatly promote the reuse value of abandoned mine land and relieve the pressure of land demand to realize the rational reuse of abandoned mine land based on the future land use structure and spatial layout of mountainous area. In this paper, optimization of the spatial structure of mountainous abandoned mine land reuse is realized through the system dynamics model and CLUE-S model. Mentougou district, Beijing, China is selected as the research area. System dynamics model with feedback functions is constructed to simulate land use structure from 2011 to 2025, which is taken as the quanfiiative constraint on spatial structure optimization. CLUE-S model with neighborhood analysis function is applied to simulate future land use spatial structure. The simulation result layer is superimposed with the abandoned mine land distribution layer and the optimized spatial structure of abandoned mine land reuse then is determined, checked by reuse suitability evaluation. The result shows that abandoned mine land can be fully optimized as other land use types according to demand, and the reuse directions are water conservancy facilities land, urban land, rural residential land, tourism land, garden land, woodland and grassland. The trend of abandoned mine land reuse tend to be consistent with land use types of neighboring patches. This study can provide theoretical reference for the practices of mountainous abandoned mine land reuse.展开更多
The demand for Li-ion batteries (LIBs) for vehicles is increasing. However, LIBs use valuable rare metals, such as Co and Li, aswell as environmentally toxic reagents. LIBs are also necessary to utilize for a long per...The demand for Li-ion batteries (LIBs) for vehicles is increasing. However, LIBs use valuable rare metals, such as Co and Li, aswell as environmentally toxic reagents. LIBs are also necessary to utilize for a long period and to recycle useful materials. The reduction, reuse,and recycle (3R) of spent LIBs is an important consideration in constructing a circular economy. In this paper, a flowsheet of the 3R of LIBs isproposed and methods to reduce the utilization of valuable rare metals and the amount of spent LIBs by remanufacturing used parts and designingnew batteries considering the concept of 3R are described. Next, several technological processes for the reuse and recycling of LIBs are introduced.These technologies include discharge, sorting, crushing, binder removal, physical separation, and pyrometallurgical and hydrometallurgicalprocessing. Each process, as well as the related physical, chemical, and biological treatments, are discussed. Finally, the problem of developedtechnologies and future subjects for 3R of LIBs are described.展开更多
Two different kinds of black liquor from the papermaking industry were treated by acidification and reuse. The experimental parameters and conditions were discussed in detail. The experimental results indicated that t...Two different kinds of black liquor from the papermaking industry were treated by acidification and reuse. The experimental parameters and conditions were discussed in detail. The experimental results indicated that the treatment process mentioned in this article is an effective process for the treatment of black liquor from the papermaking industry. By the treatment, the solid materials in black liquor are transferred into two by products and the other components are reused or evaporated. Thus, no wastewater except some condensation water would be discharged in pulping process and the problem of pollution of black liquor would be effectively solved.展开更多
To deal with a bottom up process model for design reuses a specific extended house of quality(EHOQ)is proposed Two kinds of supported functions,basic supported functions and new supported functions,are defined.Two ...To deal with a bottom up process model for design reuses a specific extended house of quality(EHOQ)is proposed Two kinds of supported functions,basic supported functions and new supported functions,are defined.Two processes to determine two kinds of functions are presented A kind of EHOQ matrix for a company is given and its management steps are studied.展开更多
Configuration knowledge is a dynamic information set which is evolving and enriching on and on. Product model is the instantiation of configuration knowledge and the evolution of configuration knowledge is the essenti...Configuration knowledge is a dynamic information set which is evolving and enriching on and on. Product model is the instantiation of configuration knowledge and the evolution of configuration knowledge is the essential inherent reason which causes the models dynamic evolvement. In the traditional model evolvement process, the inheriting and reuse of configuration knowledge was always ignored. Aim at solving the above problem, the multistage rhombus evolution mode of configuration knowledge is discussed in this paper. The product model based on configuration knowledge is put forward in different levels to achieve the models dynamic evolvement and automatic upgrading. The evolving configuration knowledge drives the product model to evolve directly according to the rule of up-layer evolvement. Furthermore, a new configuration knowledge reuse and optimization technology is presented to inheriting and reuse the foregone configuration knowledge in the course of model evolvement. At last, the air separation equipment which is related with the project is taken as an example to illuminate that the presented model evolvement and configuration knowledge reuse technology are validity and practical.展开更多
Sustainable production of clean water is a global challenge.While we firmly believe that membrane technologies are one of the most promising solutions to tackle the global water challenges,one must reduce their energy...Sustainable production of clean water is a global challenge.While we firmly believe that membrane technologies are one of the most promising solutions to tackle the global water challenges,one must reduce their energy consumption and fouling propensity for broad sustainable applications.In addition,different membranes face various challenges in their specific applications during long-term operations.In this short review,we will summarize the recent progresses in emerging membrane technologies and system integration to advance and sustain water reuse and desalination with discussion on their challenges and perspectives.展开更多
The demand for potable water is rising rapidly due to an ever-increasing population,economic activities,and dwindling water supplies.To provide adequate water supplies in the future,understanding the issues and challe...The demand for potable water is rising rapidly due to an ever-increasing population,economic activities,and dwindling water supplies.To provide adequate water supplies in the future,understanding the issues and challenges in the reuse of water and developing appropriate strategies for reuse will be critical.One way to augment water supplies for residential use is to reuse graywater- the wastewater from kitchens,bathrooms,and laundries.In this article,we critically review the evolution of water reuse,the definition of graywater,graywater reuse practices,volumes and flow in different situations,and graywater characteristics.We then examine the issues associated with different graywater treatment methods and how using graywater for irrigation around homes affects soil quality and plant growth.The study concludes that graywater treatment costs,human health risks,and its effect on soil quality are some of the challenges that need to be addressed in the future for widespread and sustainable reuse of graywater for irrigation around homes.展开更多
Objective To solve the three principal problems for reusing the software components, i.e., existence, discovery and availability principles, web services provided a new solution for reusing and assembling web software...Objective To solve the three principal problems for reusing the software components, i.e., existence, discovery and availability principles, web services provided a new solution for reusing and assembling web software or components under distributed environment with a series of XML-based protocols. Methods A 4+1 meta-model between atomic services, such as Sequence, Parallelism, Alternation, Substitute and Iteration, and a kind of service composition description language in composition process are investigated. Furthermore, an architecture-based service composition model with Ontology Engine is proposed, which is based on the software architecture life-cycle model and provides a mechanism for services composition with dynamic management and deployment. Results The results of the prototype system development show that the service-composed application not only reused the web service components, but also reused the data resources located in distributed databases. Conclusion The method of reused-based web services composition observably decreases the period and cost of development and greatly improves the programming efficiency.展开更多
Most used products must be maintained before they are reused. The modelingmethod for maintenance design of product level reuse based on quality function deployment ispresented. A fuzzy linear optimization model is dev...Most used products must be maintained before they are reused. The modelingmethod for maintenance design of product level reuse based on quality function deployment ispresented. A fuzzy linear optimization model is developed under financial uncertainty. Objective ofthe model is to maximize improvement rate of customer satisfaction level. Maintenance cost constrainis fuzzy. The algorithm for solution to the model is given. Its optimized results not only giveattention to satisfaction degree of cost constraint, but also maximize objective value. Anillustrative example involved water bump reuse is studied and the results show that the proposedmodel can effectively help maintenance planner determine the better design scheme.展开更多
Multi-beam satellite communication systems can improve the resource utilization and system capacity effectively.However,the inter-beam interference,especially for the satellite system with full frequency reuse,will de...Multi-beam satellite communication systems can improve the resource utilization and system capacity effectively.However,the inter-beam interference,especially for the satellite system with full frequency reuse,will degrade the system performance greatly due to the characteristics of multi-beam satellite antennas.In this article,the user scheduling and resource allocation of a multi-beam satellite system with full frequency reuse are jointly studied,in which all beams can use the full bandwidth.With the strong inter-beam interference,we aim to minimize the system latency experienced by the users during the process of data downloading.To solve this problem,deep reinforcement learning is used to schedule users and allocate bandwidth and power resources to mitigate the inter-beam interference.The simulation results are compared with other reference algorithms to verify the effectiveness of the proposed algorithm.展开更多
A methodology is presented to plan reuse strategies of common modules in a product family by using the concepts of function degradation, reliability, function requirement, cost and life time. Markov chain model is emp...A methodology is presented to plan reuse strategies of common modules in a product family by using the concepts of function degradation, reliability, function requirement, cost and life time. Markov chain model is employed to predict function degradation and reliability. A utility model is used to evaluate the preference between used modules and new modules. An example of cascading-requirment product family illustrates the main ideas of our work. The Markov models are used effectively to predict function degradation and reliability. Utility theory is helpful to evaluate the reuse options of common modules.展开更多
Aiming at difficult sorting and retrieving complicated structure assembliesin assembly lib, a method for compartmentalizing assembly design resource by conceptual productstructure model is presented. The similar assem...Aiming at difficult sorting and retrieving complicated structure assembliesin assembly lib, a method for compartmentalizing assembly design resource by conceptual productstructure model is presented. The similar assembly retrieval mechanisms of symbol assembly relationgraph matching and symbol assembly relation graph similarity are discussed. The method is validatedby taking valve rod assemblies as example.展开更多
A laboratory scale test was conducted in a combined membrane process (CMP) with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin...A laboratory scale test was conducted in a combined membrane process (CMP) with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage. Removal performance of chemical oxygen demand (COD), ammonia nitrogen (NH4^+-N), turbidity and anionic surfactants (LAS) was investigated under different conditions. It was observed that the effluent COD, NH4^+-N, turbidity and LAS flocculated in ranges of 0.19-0.85 mg/L, 0.03-0.18 mg/L, 0.0-0.15 NTU and 0.0-0.05 mg/L, respectively in spite of considerable fluctuation in corresponding influent of 2120-5350 mg/L, 79.5-129.3 mg/L, 110-181.1NTU and 4.9-5.4 mg/L. The effluent quality of the CMP could meet the requirements of mechanical water and hygiene water according to the class I water quality standards in China (GB3838-2002). The removal rates of COD, NH4^+-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradation is indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network (BPNN) theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4^+-N was 5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The results indicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4^+-N, turbidity and LAS. It also suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters in submarine.展开更多
Heat-integrated water network synthesis(HIWNS)has received considerable attention for the advantages of reducing water and energy consumptions.HIWNS is effective in water and energy sustainability.Mixed integer non-li...Heat-integrated water network synthesis(HIWNS)has received considerable attention for the advantages of reducing water and energy consumptions.HIWNS is effective in water and energy sustainability.Mixed integer non-linear programming(MINLP)is usually applied in HIWNS.In this work,a novel nonlinear programming(NLP)was proposed for HIWNS by considering wastewater reuse and wastewater regeneration reuse.Integer variables are changed to non-linear equation by the methods for identifying stream roles and denoting the existence of process matches.The model is tested by examples with single and multiple regeneration unit problems.The testing results showed that the NLP is an alternative method for HIWNS with wastewater reuse and regeneration reuse.展开更多
High Rate Algal Pond (HRAP) was constructed and operated using a mixer device to investigate its capability in treating greywater for reuse in gardening. Physico-chemical and microbiological parameters were monitored....High Rate Algal Pond (HRAP) was constructed and operated using a mixer device to investigate its capability in treating greywater for reuse in gardening. Physico-chemical and microbiological parameters were monitored. With a hydraulic retention time of 7.5 days and a solid retention time of 20 days, the average removal efficiencies (ARE) were 69% and 62% for BOD5 and COD respectively. The ARE for , and were 23%, 52% and 43% respectively. The removal of suspended solids (SS) was unsatisfactory, which could be attributed to the low average algal settling efficiencies of 9.3% and 16.0% achieved after 30 and 60 minutes respectively. The ARE of fecal coliforms, Escherichia coli and enterococci were 2.65, 3.14 and 3.17 log units respectively. In view of the results, the HRAP technology could be adapted for greywater treatment in sahelian regions. However, further studies on the diversity of the algal species growing in the HRAP unit are necessary in order to increase the removal of SS. Hazards of a reuse of the effluents are discussed on the basis of the various qualitative parameters. The residual content of E. coli was varying from 4 CFU per 100 mL. Based on WHO guidelines for greywater reuse in irrigation, the effluents could be used for restricted irrigation (E. coli < 105 CFU per 100 mL). Furthermore, the reuse potential is discussed on the basis of FAO guidelines using SAR (3.03 to 4.11), electrical conductivity (482 to 4500 μS/cm) and pH values (6.45 to 8.6).展开更多
文摘A significant portion of the national water supply can be attributed to de facto or unplanned potable reuse, though the extent of its contribution is difficult to estimate. Fortunately, the contribution of Water Resource Recovery Facility (WRRF) effluent to waters that supply drinking water treatment plants has been documented by some communities. In the United States (US), among the top 25 most impacted drinking water treatment plants by upstream WRRF, 16% of the influent flow to the drinking water treatment plant under average streamflow and up to 100% under low-flow conditions is WRRF effluent. Currently, the full extent of de facto reuse in the US may be much higher because of population growth. The scenario is no different for Beaufort-Jasper Water and Sewer Authority (BJWSA) in South Carolina, US, with contributions to the Savannah River originating from numerous WRRF and other upstream dischargers. South Carolina coastal utilities such as BJSWA are considering direct and indirect potable reuse options, driven by disposal limitations and challenges. Currently, South Carolina does not have a framework, guidelines, or regulations for reuse, but discussions have started among the regulated community. In addition to understanding the extent of de facto reuse, the state will need to develop standards and best practices to enable future adoption of planned potable reuse solutions to water resources challenges. Such guidance should address human health risk management and technical considerations regarding treatment in addition to other factors, including source control, storage, fail-safe operation, monitoring, non-cost factors, and public acceptance. This study conducted a mapping assessment specific to BJWSA, sampled at four locations on Savannah River, and observed that de facto reuse is approximately 4.6% to 5.9% during low-flow months and is within the range generally observed nationwide. When coupled with evidence that planned potable reuse can improve human health and environmental risks, this practice is a meaningful option in the water supply portfolio for many utilities.
基金supported by the Fundamental Research Funds for the Central Universities (Grant No. AE89991/403)National Natural Science Foundation of China (Grant No. 52005262)+1 种基金Natural Science Foundation of Jiangsu Province (BK20202007)National Key Research and Development Program of China (2022YFB4600800)。
文摘Laser powder bed fusion(L-PBF) has attracted significant attention in both the industry and academic fields since its inception, providing unprecedented advantages to fabricate complex-shaped metallic components. The printing quality and performance of L-PBF alloys are infuenced by numerous variables consisting of feedstock powders, manufacturing process,and post-treatment. As the starting materials, metallic powders play a critical role in infuencing the fabrication cost, printing consistency, and properties. Given their deterministic roles, the present review aims to retrospect the recent progress on metallic powders for L-PBF including characterization, preparation, and reuse. The powder characterization mainly serves for printing consistency while powder preparation and reuse are introduced to reduce the fabrication costs.Various powder characterization and preparation methods are presented in the beginning by analyzing the measurement principles, advantages, and limitations. Subsequently, the effect of powder reuse on the powder characteristics and mechanical performance of L-PBF parts is analyzed, focusing on steels, nickel-based superalloys, titanium and titanium alloys, and aluminum alloys. The evolution trends of powders and L-PBF parts vary depending on specific alloy systems, which makes the proposal of a unified reuse protocol infeasible. Finally,perspectives are presented to cater to the increased applications of L-PBF technologies for future investigations. The present state-of-the-art work can pave the way for the broad industrial applications of L-PBF by enhancing printing consistency and reducing the total costs from the perspective of powders.
文摘分析目前高中英语阅读教学存在功利化、模式僵化、碎片化、浅层化、资源利用不充分等典型问题。针对这些问题,构建REUSE模式,即Reviewing(复习)—Exploring(探索)—Unlocking(揭秘)—Sharing(分享)—Evaluating(评价)。以人教版高中《英语》必修3 Unit 3 The million pound bank note为例,探究在高中英语阅读教学中运用REUSE模式的教学流程及应用注意事项。
基金The Hi_Tech Research and Development Program(863) of China(No:2002AA601220)
文摘A water quality model for water reuse was made by mathematics induction. The relationship among the reuse rate of treated wastewater(R), pollutant concentration of reused water( Cs ), pollutant concentration of influent( C0), removal efficiency of pollutant in wastewater( E), and the standard of reuse water were discussed in this study. According to the experiment result of a toilet wastewater treatment and reuse with membrane bioreactors, R would be set at less than 40%, on which all the concerned parameters could meet with the reuse water standards. To raise R of reuse water in the toilet, an important way was to improve color removal of the wastewater.
基金This project is supported by National Natural Science Foundation of China(No.50275133) and China Hi-tech Program CIMS Topic (No.2003-China(No.50275133) and China Hi-tech Program CIMS Topic (No.2003-AA411320). Received July 22, 2003
文摘The increasing complexity and size of configuration knowledge bases requres the provisionof advanced methods supporting the development of the actual configuration process and design reuse.A new framework to find a feasible and practical product configuration method is presented in masscustomization. The basic idea of the appoach is to integrate case-based reasoning (CBR) with a con-straint satisfaction problem(CSP). The similarity measure between a crisp and range is also given,which is common in case retrieves. Based on the configuration model, a product platform and customerneeds, case adaptation is carried out with the repair-based algorithm. Lastly, the methodology in theelevator configuration design domain is tested.
基金the National Natural Science Foundation of China (41877533)Beijing Social Science Foundation (18GLB014).
文摘The mountainous abandoned mine land is often distributed in the fomi of fragmented patches. Therefore, it can greatly promote the reuse value of abandoned mine land and relieve the pressure of land demand to realize the rational reuse of abandoned mine land based on the future land use structure and spatial layout of mountainous area. In this paper, optimization of the spatial structure of mountainous abandoned mine land reuse is realized through the system dynamics model and CLUE-S model. Mentougou district, Beijing, China is selected as the research area. System dynamics model with feedback functions is constructed to simulate land use structure from 2011 to 2025, which is taken as the quanfiiative constraint on spatial structure optimization. CLUE-S model with neighborhood analysis function is applied to simulate future land use spatial structure. The simulation result layer is superimposed with the abandoned mine land distribution layer and the optimized spatial structure of abandoned mine land reuse then is determined, checked by reuse suitability evaluation. The result shows that abandoned mine land can be fully optimized as other land use types according to demand, and the reuse directions are water conservancy facilities land, urban land, rural residential land, tourism land, garden land, woodland and grassland. The trend of abandoned mine land reuse tend to be consistent with land use types of neighboring patches. This study can provide theoretical reference for the practices of mountainous abandoned mine land reuse.
文摘The demand for Li-ion batteries (LIBs) for vehicles is increasing. However, LIBs use valuable rare metals, such as Co and Li, aswell as environmentally toxic reagents. LIBs are also necessary to utilize for a long period and to recycle useful materials. The reduction, reuse,and recycle (3R) of spent LIBs is an important consideration in constructing a circular economy. In this paper, a flowsheet of the 3R of LIBs isproposed and methods to reduce the utilization of valuable rare metals and the amount of spent LIBs by remanufacturing used parts and designingnew batteries considering the concept of 3R are described. Next, several technological processes for the reuse and recycling of LIBs are introduced.These technologies include discharge, sorting, crushing, binder removal, physical separation, and pyrometallurgical and hydrometallurgicalprocessing. Each process, as well as the related physical, chemical, and biological treatments, are discussed. Finally, the problem of developedtechnologies and future subjects for 3R of LIBs are described.
文摘Two different kinds of black liquor from the papermaking industry were treated by acidification and reuse. The experimental parameters and conditions were discussed in detail. The experimental results indicated that the treatment process mentioned in this article is an effective process for the treatment of black liquor from the papermaking industry. By the treatment, the solid materials in black liquor are transferred into two by products and the other components are reused or evaporated. Thus, no wastewater except some condensation water would be discharged in pulping process and the problem of pollution of black liquor would be effectively solved.
基金This project is supported by Provincial Natural Science Foundation of both Hebei (No.699059) and Tianjin(No.003804611).
文摘To deal with a bottom up process model for design reuses a specific extended house of quality(EHOQ)is proposed Two kinds of supported functions,basic supported functions and new supported functions,are defined.Two processes to determine two kinds of functions are presented A kind of EHOQ matrix for a company is given and its management steps are studied.
基金supported by National Natural Science Foundation of China (Grant No. 50835008, Grant No. 50875237, Grant No. 50705084)National Hi-tech Research and Development Program of China (863 Program, Grant No. 2007AA04Z190, Grant No. 2008AA042301)
文摘Configuration knowledge is a dynamic information set which is evolving and enriching on and on. Product model is the instantiation of configuration knowledge and the evolution of configuration knowledge is the essential inherent reason which causes the models dynamic evolvement. In the traditional model evolvement process, the inheriting and reuse of configuration knowledge was always ignored. Aim at solving the above problem, the multistage rhombus evolution mode of configuration knowledge is discussed in this paper. The product model based on configuration knowledge is put forward in different levels to achieve the models dynamic evolvement and automatic upgrading. The evolving configuration knowledge drives the product model to evolve directly according to the rule of up-layer evolvement. Furthermore, a new configuration knowledge reuse and optimization technology is presented to inheriting and reuse the foregone configuration knowledge in the course of model evolvement. At last, the air separation equipment which is related with the project is taken as an example to illuminate that the presented model evolvement and configuration knowledge reuse technology are validity and practical.
基金supported by PUB, Singapore’s National Water Agency under the project ‘‘Development of 8 inch Novel High Efficiency Pressure-Retarded Osmosis (PRO) Membrane Modules towards Potential Pilot Testing and Field Validation” with NUS grant No. R-279-000-555-592Singapore National Research Foundation for supporting the project entitled, ‘‘Using Cold Energy from Regasification of Liquefied Natural Gas (LNG) for Novel Hybrid Seawater Desalination Technologies” (Grant number: R-279-000-456-279)BASF SE, Germany for partially funding this project with a grant number of R-279-000-363-597
文摘Sustainable production of clean water is a global challenge.While we firmly believe that membrane technologies are one of the most promising solutions to tackle the global water challenges,one must reduce their energy consumption and fouling propensity for broad sustainable applications.In addition,different membranes face various challenges in their specific applications during long-term operations.In this short review,we will summarize the recent progresses in emerging membrane technologies and system integration to advance and sustain water reuse and desalination with discussion on their challenges and perspectives.
文摘The demand for potable water is rising rapidly due to an ever-increasing population,economic activities,and dwindling water supplies.To provide adequate water supplies in the future,understanding the issues and challenges in the reuse of water and developing appropriate strategies for reuse will be critical.One way to augment water supplies for residential use is to reuse graywater- the wastewater from kitchens,bathrooms,and laundries.In this article,we critically review the evolution of water reuse,the definition of graywater,graywater reuse practices,volumes and flow in different situations,and graywater characteristics.We then examine the issues associated with different graywater treatment methods and how using graywater for irrigation around homes affects soil quality and plant growth.The study concludes that graywater treatment costs,human health risks,and its effect on soil quality are some of the challenges that need to be addressed in the future for widespread and sustainable reuse of graywater for irrigation around homes.
文摘Objective To solve the three principal problems for reusing the software components, i.e., existence, discovery and availability principles, web services provided a new solution for reusing and assembling web software or components under distributed environment with a series of XML-based protocols. Methods A 4+1 meta-model between atomic services, such as Sequence, Parallelism, Alternation, Substitute and Iteration, and a kind of service composition description language in composition process are investigated. Furthermore, an architecture-based service composition model with Ontology Engine is proposed, which is based on the software architecture life-cycle model and provides a mechanism for services composition with dynamic management and deployment. Results The results of the prototype system development show that the service-composed application not only reused the web service components, but also reused the data resources located in distributed databases. Conclusion The method of reused-based web services composition observably decreases the period and cost of development and greatly improves the programming efficiency.
基金This project is supported by National Defense Science Foundation of China(No.2001QB1014).
文摘Most used products must be maintained before they are reused. The modelingmethod for maintenance design of product level reuse based on quality function deployment ispresented. A fuzzy linear optimization model is developed under financial uncertainty. Objective ofthe model is to maximize improvement rate of customer satisfaction level. Maintenance cost constrainis fuzzy. The algorithm for solution to the model is given. Its optimized results not only giveattention to satisfaction degree of cost constraint, but also maximize objective value. Anillustrative example involved water bump reuse is studied and the results show that the proposedmodel can effectively help maintenance planner determine the better design scheme.
基金supported in part by the National Natural Science Foundation of China under Grant 62171052,Grant 61971054Science and Technology on Information Transmission and Dissemination in Communication Networks Laboratory Foundation under Grant HHX21641X002。
文摘Multi-beam satellite communication systems can improve the resource utilization and system capacity effectively.However,the inter-beam interference,especially for the satellite system with full frequency reuse,will degrade the system performance greatly due to the characteristics of multi-beam satellite antennas.In this article,the user scheduling and resource allocation of a multi-beam satellite system with full frequency reuse are jointly studied,in which all beams can use the full bandwidth.With the strong inter-beam interference,we aim to minimize the system latency experienced by the users during the process of data downloading.To solve this problem,deep reinforcement learning is used to schedule users and allocate bandwidth and power resources to mitigate the inter-beam interference.The simulation results are compared with other reference algorithms to verify the effectiveness of the proposed algorithm.
文摘A methodology is presented to plan reuse strategies of common modules in a product family by using the concepts of function degradation, reliability, function requirement, cost and life time. Markov chain model is employed to predict function degradation and reliability. A utility model is used to evaluate the preference between used modules and new modules. An example of cascading-requirment product family illustrates the main ideas of our work. The Markov models are used effectively to predict function degradation and reliability. Utility theory is helpful to evaluate the reuse options of common modules.
基金This project is supported by State High Technology Development Program of China (No.2003AA413310) National Natural Science Foundation of China(No.60375020) 973 Program of China(No. 2004CB719402, No. 2002CB312106).
文摘Aiming at difficult sorting and retrieving complicated structure assembliesin assembly lib, a method for compartmentalizing assembly design resource by conceptual productstructure model is presented. The similar assembly retrieval mechanisms of symbol assembly relationgraph matching and symbol assembly relation graph similarity are discussed. The method is validatedby taking valve rod assemblies as example.
基金This work was supported by the Heilongjiang Natural Science Foundation(No.E2007-04)the National Natural Science Foundation of China(No.50908062)the State Key Laboratory of Urban Water Resource and Environment(No.HIT-QAK200808).
文摘A laboratory scale test was conducted in a combined membrane process (CMP) with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage. Removal performance of chemical oxygen demand (COD), ammonia nitrogen (NH4^+-N), turbidity and anionic surfactants (LAS) was investigated under different conditions. It was observed that the effluent COD, NH4^+-N, turbidity and LAS flocculated in ranges of 0.19-0.85 mg/L, 0.03-0.18 mg/L, 0.0-0.15 NTU and 0.0-0.05 mg/L, respectively in spite of considerable fluctuation in corresponding influent of 2120-5350 mg/L, 79.5-129.3 mg/L, 110-181.1NTU and 4.9-5.4 mg/L. The effluent quality of the CMP could meet the requirements of mechanical water and hygiene water according to the class I water quality standards in China (GB3838-2002). The removal rates of COD, NH4^+-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradation is indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network (BPNN) theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4^+-N was 5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The results indicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4^+-N, turbidity and LAS. It also suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters in submarine.
基金financially supported by the Major Science and Technology Project of Xinjiang Bingtuan(2017AA007/02)。
文摘Heat-integrated water network synthesis(HIWNS)has received considerable attention for the advantages of reducing water and energy consumptions.HIWNS is effective in water and energy sustainability.Mixed integer non-linear programming(MINLP)is usually applied in HIWNS.In this work,a novel nonlinear programming(NLP)was proposed for HIWNS by considering wastewater reuse and wastewater regeneration reuse.Integer variables are changed to non-linear equation by the methods for identifying stream roles and denoting the existence of process matches.The model is tested by examples with single and multiple regeneration unit problems.The testing results showed that the NLP is an alternative method for HIWNS with wastewater reuse and regeneration reuse.
文摘High Rate Algal Pond (HRAP) was constructed and operated using a mixer device to investigate its capability in treating greywater for reuse in gardening. Physico-chemical and microbiological parameters were monitored. With a hydraulic retention time of 7.5 days and a solid retention time of 20 days, the average removal efficiencies (ARE) were 69% and 62% for BOD5 and COD respectively. The ARE for , and were 23%, 52% and 43% respectively. The removal of suspended solids (SS) was unsatisfactory, which could be attributed to the low average algal settling efficiencies of 9.3% and 16.0% achieved after 30 and 60 minutes respectively. The ARE of fecal coliforms, Escherichia coli and enterococci were 2.65, 3.14 and 3.17 log units respectively. In view of the results, the HRAP technology could be adapted for greywater treatment in sahelian regions. However, further studies on the diversity of the algal species growing in the HRAP unit are necessary in order to increase the removal of SS. Hazards of a reuse of the effluents are discussed on the basis of the various qualitative parameters. The residual content of E. coli was varying from 4 CFU per 100 mL. Based on WHO guidelines for greywater reuse in irrigation, the effluents could be used for restricted irrigation (E. coli < 105 CFU per 100 mL). Furthermore, the reuse potential is discussed on the basis of FAO guidelines using SAR (3.03 to 4.11), electrical conductivity (482 to 4500 μS/cm) and pH values (6.45 to 8.6).