On-Chip Micro Temperature Controllers Based on Freestanding Thermoelectric Nano Films for Low-Power Electronics

Multidimensional integration and multifunctional com-ponent assembly have been greatly explored in recent years to extend Moore’s Law of modern microelectronics.However,this inevitably exac-erbates the inhomogeneity of temperature distribution in microsystems,making precise temperature control for electronic components extremely challenging.Herein,we report an on-chip micro temperature controller including a pair of thermoelectric legs with a total area of 50×50μm^(2),which are fabricated from dense and flat freestanding Bi2Te3-based ther-moelectric nano films deposited on a newly developed nano graphene oxide membrane substrate.Its tunable equivalent thermal resistance is controlled by electrical currents to achieve energy-efficient temperature control for low-power electronics.A large cooling temperature difference of 44.5 K at 380 K is achieved with a power consumption of only 445μW,resulting in an ultrahigh temperature control capability over 100 K mW^(-1).Moreover,an ultra-fast cooling rate exceeding 2000 K s^(-1) and excellent reliability of up to 1 million cycles are observed.Our proposed on-chip temperature controller is expected to enable further miniaturization and multifunctional integration on a single chip for microelectronics.

Reinforced temperature control of a reactive double dividing-wall distillation column

The mass and thermal coupling makes the control of the reactive double dividing-wall distillation column(R-DDWDC) an especially challenging issue with a highly interactive nature. With reference to the separation of an ideal endothermic quaternary reversible reaction with the most unfavorable ranking of relative volatilities(A + B ■ C + D with α_(A)>α_(C)>α_(D)>α_(B)), the operation rationality of the R-DDWDC is studied in this contribution. The four-point single temperature control system leads to great steady-state discrepancies in the compositions of products C and D and the reason stems essentially from the failure in keeping strictly the stoichiometric ratio between reactants A and B. A temperature plus temperature cascade control scheme is then employed to reinforce the stoichiometric ratio control and helps to secure a substantial abatement in the steady-state discrepancies. A temperature difference plus temperature cascade control scheme is finally synthesized and leads even to better performance than the most effective double temperature difference control scheme. These outcomes reveal not only the operation feasibility of the R-DDWDC but also the general significance of the proposed temperature difference plus temperature cascade control scheme to the inferential control of any other complicated distillation columns.

Experimental study on temperature stress calculation and temperature control optimization of concrete based on early age parameters

Temperature control curve is the key to achieving temperature control and crack prevention of high concrete dam during construction,and its rationality depends on the accurate measurement of temperature stress.With the simulation testing machine for the temperature stress,in the present study,we carried out the deformation process tests of concrete under three temperature curves:convex,straight and concave.Besides,we not only measured the early-age elastic modulus,creep parameters and stress process,but also proposed the preferred type.The results show that at early age,higher temperature always leads to greater elastic modulus and smaller creep.However,the traditional indoor experiments have underestimated the elastic modulus and creep development at early age,which makes the calculated value of temperature stress too small,thus increasing the cracking risk.In this study,the stress values of the three curves calculated based on the strain and early-age parameters are in good agreement with the temperature stress measured by the temperature stress testing machine,which verifies the method accuracy.When the temperature changes along the concave curve,the law of stress development is in consistent with that of strength.Under this condition,the stress fluctuation is small and the crack prevention safety of the concave type is higher,so the concave type is better.The test results provide a reliable basis and support for temperature control curve design and optimization of concrete dams.

Response of Over-summer Hydroponic Lettuce to Nutrient Solution Temperature Control

Temperature, as an important feature of hydroponic nutrient solution, is closely related to dissolved oxygen content of nutrient solution and growth status of plant roots. How to precisely adjust the temperature of nutrient solution is the key to obtain high quality and high yield of hydroponic vegetables over summer. With Lactuca sativa vat. crispa ＇Luosheng No.3＇ as the test material, the effect of chiller cooling technology on the temperature of nutrient solution, as well as on the yield and quality of Luosheng No.3, in over-summer hydroponic cultivation was studied. The results showed that the chiller cooling technology controlled the nutrient solution temperature in a reasonable range （（20 ± 1）℃） and promoted the growth and dry matter accumulation of Luosheng No.3, instead of affecting the quality. In short, the chiller cooling technology is applicable to the temperature regulation of nutrient solu- tion in hydroponics over summer.

Studies on the Economical and Practical Temperature Control Facility of Deep-Litter Systems for Swine Production

Deep-Litter System is a high yield approach to raise swine with pollution free in a lower cost. In the research, based on the heat stress in summer caused by fermentation, three temperature-control systems were designed, including natural ventilation through transoms, forced ventilation via fans, and cooling by hyperbaric spray system. Specifically, the latter intermittent auto-pressurized spray system developed in our lab, which could spray successively via pressure from storage tubes without wetting the fermentation bed, is suitable for the promotion with the deep-litter technology in rural regions , since the power consumption is only 1 kwh per day.

Preference-based multiobjective artificial bee colony algorithm for optimization of superheated steam temperature control

In order to incorporate the decision maker＇s preference into multiobjective optimization a preference-based multiobjective artificial bee colony algorithm PMABCA is proposed.In the proposed algorithm a novel reference point based preference expression method is addressed.The fitness assignment function is defined based on the nondominated rank and the newly defined preference distance.An archive set is introduced for saving the nondominated solutions and an improved crowding-distance operator is addressed to remove the extra solutions in the archive.The experimental results of two benchmark test functions show that a preferred set of solutions and some other non-preference solutions are achieved simultaneously.The simulation results of the proportional-integral-derivative PID parameter optimization for superheated steam temperature verify that the PMABCA is efficient in aiding to making a reasonable decision.

A Two-stage pH and Temperature Control with Substrate Feeding Strategy for Production of Gamma-aminobutyric Acid by Lactobacillus brevis CGMCC 1306

Methods to optimize the production of gamma-aminobutyric acid （GABA） by Lactobacillus brevis CGMCC 1306 were investigated. Results indicated that cell growth was maximal at pH 5.0, while pH 4.5 was pref-erable to GABA formation. The optimal temperature for cell growth （35 °C） was lower than that for GABA forma-tion （40 °C）. In a two-stage pH and temperature control fermentation, cultures were maintained at pH 5.0 and 35 °C for 32 h, then adjusted to pH 4.5 and 40 °C, GABA production increased remarkably and reached 474.79 mmol·L-1 at 72 h, while it was 398.63 mmol·L-1 with one stage pH and temperature control process, in which cultivation con-ditions were constantly controlled at pH 5.0 and 35 °C. In order to avoid the inhibition of cell growth at higher L-monosodium glutamate （L-MSG） concentrations, the two-stage control fermentation with substrate feeding strat-egy was applied to GABA production, with 106.87 mmol （20 g） L-MSG supplemented into the shaking-flask at 32 h and 56 h post-inoculation separately. The GABA concentration reached 526.33 mmol·L-1 at 72 h with the fer-mentation volume increased by 38%. These results will provide primary data to realize large-scale production of GABA by L. brevis CGMCC 1306.

Real-Time Temperature Control for High Arch Dam Based on Decision Support System

It is important and difficult to control the temperature of mass concrete structure during high arch dam construction.A new method with decision support system is presented for temperature control and crack prevention.It is a database system with functions of data storage,information inquiry,data analysis,early warning and resource sharing.Monitoring information during construction can be digitized via this system,and the intelligent analysis and dynamic control of concrete temperature can be conducted.This method has been applied in the construction of the Dagangshan Arch Dam in China and has proven to be very convenient.Based on the decision support of this system and the dynamic adjustment of construction measures,the concrete temperature of this project is well-controlled.

Dynamic Thermal Model and Temperature Control of Proton Exchange Membrane Fuel Cell Stack

A dynamic thermal transfer model of a proton exchange membrane fuel cell (PEMFC) stack is developed based on energy conservation in order to reach better temperature control of PEMFC stack. Considering its uncertain parameters and disturbance, we propose a robust adaptive controller based on backstepping algorithm of Lyaponov function. Numerical simulations indicate the validity of the proposed controller.

Temperature control and cracking prevention in coastal thin-wall concrete structures

A three-dimensional finite element program for thermal analysis of hydration heat in concrete structures with a plastic pipe cooling system is introduced in this paper. The program was applied to simulation of the temperature and stress field of the Cao＇e Sluice during the construction period. From the calculated results, we can find that the temperaiure and stress of concrete cooled with plastic pipes are much lower than those of concrete without pipes. Moreover, plastic pipes could not be corroded by seawater. That is to say, a good effect of temperature control and cracking prevention can be achieved, which provides a useful reference for other similar nearshore concrete projects.

Preparation of graphene oxides with different sheet sizes by temperature control

The sheet size of a graphene oxide （GO） can greatly influence its electrical, optical, mechanical, electrochemical and catalytic property. It is a key challenge to how to control the sheet size during its preparation in different application fields. According to our previous theoretical calculations of the effect of temperature on the oxidation process of graphene, we use Hummers method to prepare GOs with different sheet sizes by simply controlling the temperature condition in the process of the oxidation reaction of potassium permanganate （KMnO4） with graphene and the dilution process with deionized water. The results detected by transmission electron microscopy （TEM） and atomic force microscopy （AFM） show that the average sizes of GO sheets prepared at different temperatures are about 1 μm and 7 μm respectively. The ultraviolet-visible spectroscopy （UV-vis） shows that lower temperature can lead to smaller oxidation degrees of GO and less oxygen functional groups on the surface. In addition, we prepare GO membranes to test their mechanical strengths by ultrasonic waves, and we find that the strengths of the GO membranes prepared under low temperatures are considerably higher than those prepared under high temperatures, showing the high mechanical strengths of larger GO sheets. Our experimental results testify our previous theoretical calculations. Compared with the traditional centrifugal separation and chemical cutting method, the preparation process of GO by temperature control is simple and low-cost and also enables large-size synthesis. These findings develop a new method to control GO sheet sizes for large-scale potential applications.

A Soil Temperature Control System for Sapling Study in Alpine Region

A soil temperature control system was designed for sapling study in alpine region and tested in summer, 2009. The system consisted of a power switch, voltage regulator, microcomputer timer, safety relays, temperature control device, temperature sensors, heating cables, fireproofing plastic pipes (PVC), 108 heavy-duty plastic containers and seedlings. The heating cables were held in six 2-layer PVC frames with 25 cm wide, 320 cm long and 25 cm high and three 1-layer frames with 25 cm wide and 320 cm long for 15°C soil temperature treatment, half of the 2-layer frames were used for 20°C and 25°C soil temperature treatments, respectively. Each of the frames was installed at each of ditches with 30 cm wide, 330 cm long and 30 cm deep in size. 12 seedling containers with 20 cm top diameter, 18cm bottom diameter and 25 cm high were homogenously placed at each of the ditches, and spaces between the containers were filled with natural soil. The system was economic, and could increase soil temperatures obviously and uniformly, the maximal and minimal standard errors of soil temperatures were ±0.28 and ±0.05°C at 10cm depth in the containers within each of all the ditches. In the system, aboveground environment was natural, diurnal and monthly soil temperatures varied with changing air temperature, the research results may be better to know the eco-physiological and growth responses of alpine saplings/seedlings to soil warming than that in greenhouse, laboratory, infrared heat lamp and open top chamber.

Research on the principle of space high-precision temperature control system of liquid crystals based Stokes polarimeter

The magnetic field is one of the most important parameters in solar physics,and a polarimeter is the key device to measure the solar magnetic field.Liquid crystals based Stokes polarimeter is a novel technology,and will be applied for magnetic field measurement in the first space-based solar observatory satellite developed by China,Advanced Space-based Solar Observatory.However,the liquid crystals based Stokes polarimeter in space is not a mature technology.Therefore,it is of great scientific significance to study the control method and characteristics of the device.The retardation produced by a liquid crystal variable retarder is sensitive to the temperature,and the retardation changes 0.09°per 0.10℃.The error in polarization measurement caused by this change is 0.016,which affects the accuracy of magnetic field measurement.In order to ensure the stability of its performance,this paper proposes a high-precision temperature control system for liquid crystals based Stokes polarimeter in space.In order to optimize the structure design and temperature control system,the temperature field of liquid crystals based Stokes polarimeter is analyzed by the finite element method,and the influence of light on the temperature field of the liquid crystal variable retarder is analyzed theoretically.By analyzing the principle of highprecision temperature measurement in space,a high-precision temperature measurement circuit based on integrated operational amplifier,programmable amplifier and 12 bit A/D is designed,and a high-precision space temperature control system is developed by applying the integral separation PI temperature control algorithm and PWM driving heating films.The experimental results show that the effect of temperature control is accurate and stable,whenever the liquid crystals based Stokes polarimeter is either in the air or vacuum.The temperature stability is within±0.0150℃,which demonstrates greatly improved stability for the liquid crystals based Stokes polarimeter.

Studies on Composting Spent Coffee Grounds by <i>Aspergillus sp</i>and <i>Aspergillus sp</i>in Aerobic Static Batch Temperature Control

Spent Coffee Ground (SCG) is characterized by high organic content, in the form of insoluble polysaccharides bound and phenol compounds. Phenol compounds are toxic to nature and are a cause of environmental pollution. Composting method of this study is aerobic static batch composting with temperature control with adding activators of some fungi such as Aspergillus sp, and Penicillium sp. The purpose of the research is to fill the research gap from previous studies of spent coffee grounds compost, which requires a long time in composting, so that if it is used directly on the soil and plants, the positive effect also requires a long time. The result of composting for 28 days with this method is that mature compost has black crumb and normal pH, with characteristics of C/N ratio below 10: C1 (7.06), C2 (6.99). This value is far from the control with a C/N ratio of 8.33. Decompose rate of macromolecule are above 40% for lignin and 70% for cellulose. Implementation of compost in radish plants, resulting Germination Index above 80% which indicates that the compost is ripe: control (92.39%), C1 (183.88%), C2 (191.86%). The results of the analysis with FTIR also showed that the compost was mature and stable, and rich in minerals. So, it can be concluded that this composting method can speed up composting time and optimize the results of compost produced.

Finite-time Stability of Heating Furnace Temperature Control System

A finite-time stabilization controller for the heating furnace temperature control system is proposed.Based on the extended Lyapunov finite-time stability theory and power integral method,a finite-time stable condition of the heating furnace temperature control system is given.The temperature of the heating furnace is directed by the finite-time stabilization controller to make it stable in finite time.And the quality and quantity of slabs is improved.The simulation example is presented to illustrate the applicability of the developed results.

Application of Improved Neural Adaptive PSD Algorithm in Temperature Control of INS

A neural adaptive proportion sum differential (PSD) algorithm with errors prediction is researched. It is applied in inertial navigation system(INS) temperature control. The algorithm do not need the process's precise mathematical model and can adapt to the process parameters changing, and can deal with the process with nonlinearity. According to the Smith predictor, author developed a method that takes the predicted process error and error change as neural adaptive PSD algorithm's input. The method is effective to the system with long dead time. The results of compute simulation show that this system has characters of quickly reaction, low overshoot and good stability. It can meet the requirements of temperature control of INS.

Direct incorporation of paraffin wax as phase change material into mass concrete for temperature control: mechanical and thermal properties

Taking advantage of heat absorbing and releasing capability of phase change material(PCM),Paraffin wax-based concrete was prepared to assess its automatic temperature control performance.The mechanical properties of PCM concrete with eight different Paraffin wax contents were tested by the cube compression test and four-point bending test.The more Paraffin wax incorporated,the greater loss of the compressive strength and bending strength.Based on the mechanical results,four contents of Paraffin wax were chosen for studying PCM concrete's thermal properties,including thermal conductivity,thermal diffusivity,specific heat capacity,thermal expansion coefficient and adiabatic temperature rise.When the Paraffin wax content increases from 10%to 20%,the thermal conductivity and the thermal diffusivity decrease from 7.31 kJ/(m·h·°C)to 7.10 kJ/(m·h·°C)and from 3.03×10−3 m2/h to 2.44×10−3 m2/h,respectively.Meanwhile the specific heat capacity and thermal expansion coefficient rise from 5.38×10−1 kJ/(kg·°C)to 5.76×10−1 kJ/(kg·°C)and from 9.63×10−6/°C to 14.02×10−6/°C,respectively.The adiabatic temperature rise is found to decrease with an increasing Paraffin wax content.Considering both the mechanical and thermal properties,15%of Paraffin wax was elected for the mass concrete model test,and the model test results confirm the effect of Paraffin wax in automatic mass concrete temperature control.

Determination of Impurity Silicon in Anticancer Drug (Ge-132) by Electrothermally Atomised Atomic Absorption Spectrometry with Optical Temperature Control Accessory

The present paper describes the ashing and atomization processes in silicon analysis by electrothermally atomised atomic absorption spectrometry(EAAAS) with an uncoat-ed graphite tube, a pyrolytically coated graphite tube and a tungsten-coated graphitetube. The sensitivity and linear range of three graphite tubes were compared. By using optical temperature control accessory, the signals are enhanced by a factor of 2 and the germanium interferences in the determination of silicon are eliminated. The effects of time constant and carrier gas flow-rate on the determination of silicon were also tested. The sample can be directly analyzed in its aqueous solution without any pretreatment. The measurements of samples containing 0. 2 μg/mL and 0. 4 μg/mL silicon were run ten times and the variation coefficient is 4. 9% and 2.6%, respectively. The recovery tests for carboxyethyl germanium sesquioxide(Ge-132) synthesized and imported were performed, and the recoveries are 97. 0% and 110%, respectively. Keywords Carboxyethyl germanium sesquioxide, Electrothermally atomised atomic absorption spectrometry, Silicon

Color-Changing Fabric System with Temperature Control

Color-changing fabric system with temperature control is designed through textile design and electronic technology.The system inserts a conductive fabric inside a fabric coated with thermochromic powder.A temperature control system is constructed to adjust the current to raise the temperature of conductive fabric to the active point of thermochromic powder and keep the temperature in stable.Therefore,the fabric could sense the temperature and change colors.In order to achieve wearability,mobile power supply is selected and flexible sensor is adopted.Kalman filter is engaged in the proportion integration differentiation(PID)control algorithm to reduce the interference of measurement noise.The experiment result shows that the proposed color-changing fabric system could reach the target temperature quickly and meet the design demands for color-changing.

Design and Research on New Intelligent Temperature Control System for Stove

A new intelligent temperature control system for stove was introduced. It could accomplish A/D conversion, data processing, output displaying and alarming while the temperature exceeds the given threshold. The temperature adjusting devices were bi direction SCR and heating resistor. The hardware and software were discussed in the paper.