Temperature and stress fields in electron beam welded Ti-15-3 alloy to 304 stainless steel joint with copper interlayer sheet

Electron beam welding of Ti-15-3 alloy to 304 stainless steel （STS） using a copper filler metal was carried out. The temperature fields and stress distributions in the Ti/Fe and Ti/Cu/Fe joint during the welding process were numerically simulated and experimentally measured. The results show that the rotated parabola body heat source is fit for the simulation of the electron beam welding. The temperature distribution is asymmetric along the weld center and the temperature in the titanium alloy plate is higher than that in the 304 STS plate. The thermal stress also appears to be in asymmetric distribution. The residual tensile stress mainly exists in the weld at the 304 STS side. The copper filler metal decreases the peak temperature and temperature grade in the joint as well as the residual stress. The longitudinal and lateral residual tensile strengths reduce by 66 MPa and 31 MPa, respectively. From the temperature and residual stress, it is concluded that copper is a good filler metal candidate for the electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel.

Electron beam welding of 304 stainless steel to QCr0.8 copper alloy with copper filler wire

Electron beam welding （EBW） of 304 stainless steel to QCr0.8 copper alloy with copper filler wire was carried out. Orthogonal experiment was performed to investigate the effects of process parameters on the tensile strength of the joints, and the process parameters were optimized. The optimum process parameters are as follows：beam current of 30 mA, welding speed of 100 mm/min, wire feed rate of 1 m/min and beam offset of-0.3 mm. The microstructures of the optimum joint were studied. The results indicate that the weld is mainly composed of dendriticαphase with little globularεphase, and copper inhomogeneity only occurs at the top of the fusion zone. In addition, a melted region without mixing exists near the weld junction of copper side. This region with a coarser grain size is the weakest section of the joints. It is found that the microhardness of the weld decreases with the increase of the copper content in solid solution. The highest tensile strength of the joint is 276 MPa.

Electrochemical Synthesis of Phenol-aniline Copolymerization Coating on 304 Stainless Steel Anodes and Coating Microstructure Analysis

Electrochemical copolymerization of phenol and aniline was achieved on 304 stainless steel anodes in neutral water solution with an electrolyte of Na2SO4O4. Compared with pit corrosion potential of different copolymer coatings, the best solution composition was 0.09 mol/L phenol and 0.01 mol/L aniline. Through infrared spectrum analysis, polyaniline structure was proved in phenol-aniline copolymer, as well as more side chains. Scanning electron microscope was used to analyze microstructure of copolymer coating, taking advantage of part solubility of phenol-aniline eopolymer in tetrahydrofuran, the bifurcate network structure was observed. The copolymer coating microstructure was summarized, compared with the performance of polyphenol coatings, the reasons of corrosion resistance enhancement with the addition of aniline in electropolymerization reaction was assumed as well.

Effects of Laser Shock Processing on Mechanical Properties of Laser Welded ANSI 304 Stainless Steel Joint

With the rapid development of engineering component with integration,high-speed and multi-parameter,traditional techniques haven＇t met practical needs in extreme service environment.Laser welding,a new welding technology,has been widely used.However,it would generate the drop of mechanical properties for laser welded joint due to its thermal effect.Laser shock processing（LSP） is one of the most effective methods to improve the mechanical properties of laser welded ANSI 304 stainless steel joint.In this paper,the effects of LSP on the mechanical properties of laser welded ANSI 304 stainless steel joint have been investigated.The welded joint on the front of the tensile samples is treated by LSP impacts,and the overlapping rate of the laser spot is 50%.The tensile test of the laser welded joint with and without LSP impacts is carried out,and the fracture morphology of the tensile samples is analyzed by scanning electron microscope（SEM）.Compared with the yield strength of 11.70 kN,the tensile strength of 37.66 kN,the yield-to-tensile strength ratio of 0.310 7,the elongation of 25.20%,the area reduction of 32.68% and the elastic modulus of 13 063.876 MPa,the corresponding values after LSP impacts are 14.25 kN,38.74 kN,0.367 8,26.58%,42.29% and 14 754.394 MPa,respectively.Through LSP impacts,the increasing ratio of the yield strength and tensile strength are 121.79% and 102.87%,respectively;the elongation and area reduction are improved by 5.48% and 29.38%,respectively.By comparing with coarse fracture surface of the welded joint,the delamination splitting with some cracks in the sharp corner of the welded joint and asymmetric dimples,LSP can cause brighter fracture surface,and finer and more uniform dimples.Finally,the schematic illustration of dimple formation with LSP is clearly described.The proposed research ensures that the LSP technology can clearly improve the yield strength,tensile strength,yield-to-tensile strength ratio,elongation,area reduction and elastic modulus of the welded joint.The enhancement mechanism of LSP on laser welded ANSI 304 stainless steel joint is mainly due to the fact that the refined and uniform dimples effectively delay the fracture of laser welded joints.

Characterization of stress corrosion crack growth of 304 stainless steel by electrochemical noise and scanning Kelvin probe

The fatigue pre-cracking 304 stainless steel （SS） specimens with lengths of 1.002 mm （L-crack） and 0.575 mm （S-crack） were prepared. Their corrosion behavior was studied by electrochemical noise （EN） in 4 mol/L NaC1 ＋ 0.01 mol/L Na2S203 solution under slow-strain-rate-testing （SSRT） conditions. Moreover, the characteristics of L-crack＇s surface morphology and potential distribution with scanning Kelvin probe （SKP） before and after SSRT were also discussed. Compared with S-crack, L-crack is propagated and the features of crack propagation can be obtained. After propagation, the noise amplitudes increase with increasing stress and accelerating corrosion, the white noises at low and high frequencies （WE and WH） of the later stage are one order of magnitude larger than that at early stage in the current power spectral densities （PSDs）. The potential PSDs also increase, but WH disappears. In addition, the crack propagation can be demonstrated according to variation of probability distribution, surface morphology and potential distribution.

Development of processing windows for diffusion bonding of Ti-6Al-4V titanium alloy and 304 stainless steel with silver as intermediate layer

As titanium alloy is chemically reactive,it is very difficult to join by conventional welding techniques.Titanium alloys can easily pick up nitrogen and oxygen from the atmosphere.In the fusion welding method,brittle intermetallic compounds are formed when joining titanium alloy and stainless steel,which decrease the mechanical behavior of the couples.Hence,for joining of titanium alloy,diffusion bonding is recommended.This work dealt with the measurement of feasible process parameters for diffusion bonding of Ti-6Al-4V and AISI 304 stainless steel with silver as an intermediate layer.The quality of the bonds was confirmed by the lap shear test and microstructural analysis.With the experimental results obtained,diffusion bonding windows were constructed and this will act as reference maps to identify the process parameters for obtaining defect free bond.Bonding was successful in the temperature range of 750-800 °C.Maximum lap shear strength was achieved under a bonding pressure of 5 MPa and holding time of 90 min.

Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with copper interlayer sheet

Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy(SEM) and X-ray diffractometry(XRD).In addition,the mechanical properties of the joint were evaluated by tensile test and the microhardness was measured.These two alloys were successfully welded by adding copper transition layer into the weld.Solid solution with a certain thickness was located at the interfaces between weld and base metal in both sides.Regions inside the weld and near the stainless steel were characterized by solid solution of copper with TiFe2 intermetallics dispersedly distributed in it.While weld near titanium alloy contained Ti-Cu and Ti-Fe-Cu intermetallics layer,in which the hardness of weld came to the highest value.Brittle fracture occurred in the intermetallics layer when the joint was stretched.

Investigation of SUS304 Stainless Steel with Warm Hydro-mechanical Deep Drawing

Basing on warm mechanical property of SUS304 stainless steel and hydro-mechanical deep drawing process, warm hydro-mechanical deep drawing process is proposed and discussed with experiments in this paper. The experiments are performed at four different temperatures. The results show that the formability of stainless steel is improved under the condition of warm temperature. Warm hydro-mechanical deep drawing raises limiting drawing ratio of SUS304 effectively, and limiting drawing ratio 3.3 is obtained, which is beyond 2.0 with conventional deep drawing. The temperature of 90℃ is beneficial to the forming of SUS304 stainless steel, the strain-induced martensite is controlled effectively, and the thickness distribution is more uniform.

Gas tungsten arc welding of CP-copper to 304 stainless steel using different filler materials

The dissimilar joining of CP-copper to 304 stainless steel was performed by gas tungsten arc welding process using different filler materials. The results indicated the formation of defect free joint by using copper filler material. But, the presence of some defects like solidification crack and lack of fusion caused decreasing tensile strength of other joints. In the optimum conditions, the tensile strength of the joint was 96% of the weaker material. Also, this joint was bent till to 180° without any macroscopic defects like separation, tearing or fracture. It was concluded that copper is a new and good candidate for gas tungsten arc welding of copper to 304 stainless steel.

Static and dynamic finite element analysis of 304 stainless steel rod and wire hot continuous rolling process

Three-dimensional finite element models were developed to analyze 304 stainless steel rod and wire hot continuous rolling process with the help of MSC.Marc software. The entire 30-pass deformation process and the actual parameters of production line were taken into account. Static and dynamic procedures were used to study the continuous rolling process with the aid of the thermo-mechanical coupled FEM of elastic-plasticity. The properties of billets, such as deformation, temperature field and rolling force, were mainly discussed. The simulation results of temperature agree well with the measured values. Comparisons of the analysis results obtained using static implicit method and dynamic implicit method were presented. It is shown that static implicit procedure is more accurate than dynamic implicit procedure and is able to simulate the rolling process with a lower speed, such as a roughing mill. Whereas, dynamic analysis shows a higher efficiency than static analysis and is fit for simulating the rolling process with a higher speed, such as a finishing mill.

Uniaxial Time-Dependent Ratcheting of SS304 Stainless Steel at High Temperatures

The uniaxial time-dependent strain cyclic behaviors and ratcheting of SS304 stainless steel were studied at high temperatures （350 ℃ and 700 ℃）. The effects of straining and stressing rates, holding time at the peak and/or valley of each cycle in addition to ambient temperature on the cyclic softening/hardening behavior and ratcheting of the material were discussed. It can be seen from experimental results that the material presents remarkable time dependence at 700 ℃, and the ratcheting strain depends greatly on the stressing rate, holding time and ambient temperature. Some significant conclusions are obtained, which are useful to build a constitutive model describiog the time-dependent cyclic deformation of the material.

Effect of W/Cu composite filler metals on the microstructure and mechanical properties of laser welded pure niobium/304 stainless steel joint

Cracking in a laser weld of niobium to stainless steel occurred due to the formation of brittle,continuously distributed Nb-Fe intermetallic compounds.A crack-free joint,which had a tensile strength of 147 MPa,was obtained by using the W/Cu composite filler metals.To determine the reasons for cracking in the Nb/SS joint and the function of the W/Cu composite filler metals on the improvement of the cracking resistance of the Nb/W/Cu/SS joint,the microstructures of the joints were studied by optical microscopy,scanning electron microscopy and X-ray diffraction.The cracking susceptibilities of the joints were evaluated with microhardness test on the cross section of the Nb/W/Cu/SS joint.The results showed that the Nb/W/Cu/SS joint was characterized by various solid solution.The formation of solid solution reduced the cracking susceptibility of the joint.

Study on numerical simulation of TA1-304 stainless steel explosive welding

In order to guide the explosive welding experiment of titanium-stainless steel,Three-dimensional numerical simulation of explosive welding,which select TA1 as flyer plate and 304 stainless steel as base plate,is carried out by using the LS-DYNA software and SPH-FEM coupling algorithm in the present study.The explosive welding window is calculated and established.It is found that the numerical simulation results are in good agreement with the experimental results.The displacement,velocity and pressure-time curves of characteristic elements show that the quality of explosive welding composites is superior.It is proved that SPH-FEM coupling algorithm is effective for explosive welding of TA1/304 stainless steel and can effectively guide the selection of explosive welding parameters.

Fractal Characteristic of Pits Distribution on 304 Stainless Steel Corroded Surface and Its Application in Corrosion Diagnosis

Electrochemical techniques and fractal theory were employed to study the corrosion behaviors and pits distribution characteristics on the corroded surfaces of 304 stainless steel exposed in FeCl3 solution. Fractal features of pits distribution over the corroded surfaces were observed and described by the fractal dimension. A 5-8-2 back-propagation （BP） artificial neural network model for the diagnoses of the pitting corrosion rate and pits deepness of 304 stainless steel under various conditions was developed by considering the fractal dimension as a key parameter for describing the pitting corrosion characteristics. The predicted results are well in agreement with the experimental data of pitting corrosion rate and pit deepness. The max relative errors between their experimental and simulation data are 6.69% and 4.62%, respectively.

Study of Pitting Morphology Fractal Characteristic of Corroded Surface of 304 Stainless Steel in FeCl_3 Environment

Experiments were performed to study the pitting corrosion morphology of 304 stainless steel exposed to FeCl 3 environments and SEM micrographs of the pitting corrosion morphology were obtained. The image processing technique combining with the fractal method was employed to analyze these pitting corrosion images and the self-similarity of pits morphology was observed. It indicates that fractal characteristics exist in pitting corrosion of 304 stainless steel. The self-similarity and complexity of the pitting morphology phenomenon were described in terms of fractal dimension which can also be an important parameter related to characterize pitting morphology qualitatively and quantitatively.

Microstructure and corrosion resistance of 304 stainless steel electroslag strip cladding

The 304 stainless steel strips were deposited one layer on carbon steel base metal by electroslag strip cladding （ESC） and submerged arc cladding （SAC）, respectively. The solidification microstrueture of ESC metal was analyzed by the optical microscopy, scanning electron microscope and energy dispersive spectroscopy. The corrosion resistance studies of strip cladding metals were carried out in 10% oxalic acid electrolytic etching test. The results showed that the cladding metal obtained by ESC presented low content of C, high content of Cr and enough alloying element of Ni in the chemical composition. The transition zone of ESC with small width was almost parallel with the base metal, leading to a lower dilution. There are three types of solidification modes （ A→AF→FA ） occurred in the ESC metal due to the decrease of cooling rate and degree of dilution from the transition zone to the top of ESC metal. As a result, the microstructure of ESC metal exhibited mainly austenite with a small amount of ferrite, contributing to achievement of better corrosion resistance.

Microstructure and mechanical properties of laser welded joints of pure copper and 304 stainless steels

A continuous wave diode laser with an output power of 2.8 kW was used to join pure copper and 304 stainless steel with a thickness of 1 mm. The focused laser beam with a diameter of O. 8 mm was irradiated on the copper side of the butt joints. In process of laser welding, effects of processing primary parameters on tensile strength of the joints were investigated. The interfacial characterizations of the joints were investigated by metallographic microscope, scanning electron microscope （SEM） and energy dispersive X-ray spectroscope （EDS）. The results showed that the element diffusion and solution occur and metallurgical bonding was achieved between pure copper and 304 stainless steel. The maximum tensile strength of the joints was 209 MPa when the laser power of welding was 2. 4 kW and welding speed was 12 mm/s.

Deformation Behavior and Formability of Gradient Nano-grained AISI 304 Stainless Steel Processed by Ultrasonic Impact Treatment

The deformation behavior and formability of gradient nano-grained（GNG） AISI 304 stainless steel in uniaxial and biaxial states were investigated by means of tensile test and small punch test（SPT）. The GNG top layer was fabricated on coarse grains（CG） AISI 304 by ultrasonic impact treatment. The results showed that the CG substrate could effectively suppress the strain localization of NC in GNG layer, and an approximate linear relationship existed between the thickness of substrate（h） and uniform true strain before necking（ε_（unif））. Grain growth of NC was observed at the stress state with high Stress triaxiality T, which led to better ductility of GNG/CG 304 in SPT, as well as similar true strain after the onset of necking（ε_（neck）） compared with coarse 304 in tensile test. Ei-values of GNG/CG 304 with different structures were nearly the same at different punch speeds, and good formability of GNG/CG 304 was demonstrated. However, punch speed and microstructure needed to be optimized to avoid much lost of membrane strain region in biaxial stress state.

1-Hydroxyethylidene-1,1-diphosphonic Acid (HEDP) as a Corrosion Inhibitor of AISI 304 Stainless Steel in a Medium Containing Chloride and Sulfide Ions in the Presence of Different Metallic Cations

The novelty of this paper is the analysis in a medium containing sulfide ion due to the generation of this ion in petroleum industries, in the refining stage (the sulfide ion is also present on the produced water). The performance of 1-hydroxyethylidene-1,1-diphosphonic acid inhibitor (HEDP) was investigated by potentiodynamic polarization, electrochemical impedance spectroscopy, and weight loss measurements in a dissolution of AISI 304 stainless steel immersed in a solution containing chloride and sulfide ions. The protection of the stainless was increased with the addition of divalent cations (Ca2+, Zn2+, and Mg2+). Potentiodynamic polarization studies have shown that the inhibitor alone has anodic protection, but the addition of Ca2+ (10 mg·L-1) favors the cathodic protection, and the addition of Zn2+ (20 mg·L-1) and Mg2+ (10 mg·L-1) mixed-type is observed. Electrochemical impedance spectroscopy was performed at three distinct potentials: -0.3 [V vs. SCE], Ecorr [V vs. SCE], and 0.1 [V vs. SCE]. This revealed that calcium is responsible for favoring the formation of the film and the other elements (zinc and magnesium) favor the stabilization of the protective film. Scanning electron microscopy analysis revealed that the addition of cations provided the adsorption of HEDP on the metal surface. Weight loss results showed that the presence of zinc in a solution containing HEDP favored greater inhibitor efficiency (Zn2+ ηm = 85.2% and for Mg2+ ηm = 70.4%).

Residual stress in the cylindrical drawing cup of SUS304 stainless steel evaluated by split-ring test

The residual stresses in the wall of a SUS304 stainless steel cylindrical drawing cup were evaluated by split-ring tests, and the influences of stamping die parame- ters on the residual stress were investigated. A new theoretical model of a split-ring test was developed to evaluate the resid- ual stress in a ring, which was verified to be reasonable and reliable by numerical simulations with ABAQUS code and by nanoindentation tests. Seven groups of split-ring tests were completed, and the residual stresses were calculated according to the theoretical model. The split-ring test results showed that the circumferential residual stress in the wall of the SUS304 stainless steel cylindrical drawing cup was very large and did not change with the different die comer radius. The circumferential residual stress first increased with the increase of drawing punch-die clearance, then was almost unchanged when the clearance increased greater than blank thickness 1 mm. Thus, a smaller clearance was suggested to be chosen to reduce the residual stress in the wall of the SUS304 stainless steel drawing cup.